Table of Contents
Advertisement
3 Assembling
Procedures for assembling this product are explained.
CAUTION
Make sure to unpack this product with three
persons or more.
3.1
The stand assembling procedure
If you will use the stand, assemble it in accordance
with the following steps.
1. Follow the steps shown below to assemble the
right side of the stand.
a. Attach the right support to the caster section.
b. Fasten two hexagon socket head cap screws
with the enclosed hexagonal wrench.
1
2
4
No.
Name
No.
1
Right support
4
Hexagon socket head cap
2
Caster lock
3
Caster section
2. Assemble the left side of the stand in a similar
way to step 1.
1
2
4
No.
Name
No.
1
Left support
4
Hexagon socket head cap
2
Caster lock
3
Caster section
3. Follow the steps shown below to attach the central
beam to the legs (left, right).
a. Attach the central beam and four hexagon socket
head cap screws to the stand (the left, the right).
b. Fasten the hexagon socket head cap screws with
the enclosed hexagonal wrench, and fasten the
central beam.
2
1
4
No.
Name
No.
1
Central beam
4
2
Leg (left)
3
Leg (right)
4. Follow the steps shown below to attach the
Stabilizer to the Stand.
a. Use 4 Hexagon socket head cap screws to
attach the Stabilizer to the right and left sides
of the Stand (2 each side).
b. Tighten the Hexagon socket head cap screws
using the Hexagonal wrench.
Front
3
No.
1
2
3
5. Attach the waste fluid tank holder to the right
stand using four screws.
3
Name
No.
No.
No.
screws
1
1
1
2
2
2
Waste fluid tank holder
Waste fluid tank holder
Waste fluid tank holder
6. Attach the book holder to the right side of the stand.
3
No.
1
Name
7. Confirm that each component is fastened firmly
by gently shaking the stand.
screws
3.2
Attach the stand to the printer in accordance with the
following steps.
1. Lock two casters on the front side.
3
4
No.
1
Name
2. Hold the following positions when lifting the product.
Hexagon socket head cap
screws
Panel side
Opposed side :two rubber grips under the product
1
4
Name
No.
Name
Stabilizer
4
Hexagon socket head cap
screws
Stand (left)
Stand (right)
Name
Name
Name
No.
No.
No.
Name
Name
Name
Stand (right)
Stand (right)
Stand (right)
3
3
3
Waste fluid tank holder
Waste fluid tank holder
Waste fluid tank holder
stabilizing screws
stabilizing screws
stabilizing screws
Name
No.
Name
Leg (right)
2
Book holder
Assembling the stand
1
2
Name
No.
Name
Casters
2
Caster locks
: two grips under the product
3
NOTE
Make sure to hold the specified positions when lifting
the product.
This prevents the product from being fallen and
broken.
Do not hold the media guide. This may affect the
accuracy and correct operation of the product.
4
2
3
4
2
No.
Name
1
Grips
2
Rubber grips
2
3. Place the product on the stand so that the rear rubber
leg tips fit into the holes on the stand.。
3
1
2
No.
Name
1
1
Printer main body
4. Attach two butterfly bolts to the stand.
1
2
No.
Name
1
Butterfly bolts
5. Follow the steps shown below to set the Waste
fluid tank.
a. Put the Waste fluid tank in the Waste fluid
tank holder.
b. Attach the Waste fluid tube to the Waste fluid
tank.
c. Attach the Waste fluid sensor cable to the
Waste fluid sensor connector.
5
4
2
No.
Name
1
Waste fluid tank holder
2
Waste fluid tank
3
Waste fluid tube
CS9350 INSTALLATION MANUAL
4
1
3
No.
Name
3
Rubber leg tips
4
Media guide
1
2
No.
Name
2
Holes on the stand
1
3
1
No.
Name
4
Waste fluid sensor cable
5
Waste fluid sensor
connector
AP-40800 - 1.0
Advertisement
Table of Contents
