Table of Contents
Advertisement
CLIO Service Manual
6.
Lift the U-shaped Metal Arm straight up (27) and away from the CLIO unit and store in a
safe location. You may need to use a miniature screwdriver to gently pry the Top Hinge
(16) from its position on the hinge arm (27).
7.
Note that the opening where the flex circuit (8) and wires emerge from the top and
bottom Display Bezel halves has slotted plastic bushings (4). Using either a pair of
tweezers or a pair of miniature needle-nose pliers, gently spread the bushings (4) open
and slide them off the Display Bezel halves (1, 2). Carefully thread the flex circuit (8) and
wires through the slot in the bushings (4) and store the bushings (4) in a secure location.
8.
Using either fingernails or a miniature jewelry screwdriver, carefully work your way
around the CLIO unit and separate the Display Bezel halves (1, 2), taking care not to
break any of the slots and tabs. Lift the Display Top (1) straight up. Store in a secure
location.
5.10.2.
D
T
ISPLAY
OP
1.
To replace the Display Top (1), the CLIO unit should be oriented with the hinge side
facing the technician and the LCD Unit (large silver plate) facing up.
2.
Gently work your way around the CLIO inserting and fastening the various tabs and slots
to mate the two halves of the Display Bezel (1, 2). Use caution to avoid damaging the
flex circuit (8) and wires. Make sure that the flex circuit and wires emerge through the
opening in the Display Bezels (1, 2) and that they are not pinched between the two
halves.
3.
Using either tweezers or miniature needle-nose pliers, gently spread open the slot on the
bushings (4) and thread the bushings (4) over the flex circuit and wires, taking care not to
damage the flex circuit (8) and wires. Slide the bushings (4) into place over the opening
in the Display Bezels (1, 2).
4.
Lay the U-shaped Metal Arm (27) into position. Grasping the CLIO unit securely, rotate it
into standard orientation.
5.
Lay the right side lower hinge arm in place (26), taking care to avoid pinching the flex
circuit (8) and wires. Insert the washers (18, 23) in their locations as shown in photo 5.
Fasten the arm (26) in place using one M3x6 (17)(display end) and one M3x10 (24)(base
end) screw and a #2 Phillips head screwdriver torqued to 1.0N.M. Replace the rubber
plugs (19, 21) above the screws. Repeat for the left side.
5.11.
D
ISPLAY
Please refer to photos 4-6, 22, 23, 27 in Chapter 2.
5.11.1.
D
B
ISPLAY
EZEL
1.
Insert a piece of soft cloth between the CLIO Keyboard Top (47) and the Display Bezel
(2) to avoid scratching or marring the LCD Unit (66) or Display Bezel (2).
2.
Follow the Display Top removal procedure, above.
3.
Locate the four #1 Phillips head screws (10)(one near each corner of the LCD Unit ).
4.
Remove the four #1 Phillips head screws (10) using a #1 Phillips head screwdriver.
Store in a secure location.
The information contained in this document is confidential and the sole property of Vadem Inc. Written
permission must be obtained to reprint or use any of this information.
AUTHORED BY ANTHONY HERNANDEZ - (415)786-2081 - anthonyh@ashlandhome.net
– R
EFIT
B
– R
EZEL
EMOVE
– R
EMOVAL
5-8
CLIO Tear-down & Rebuild
& R
EFIT
Advertisement
Table of Contents
