Download  Print this page

Options - Kenmore 110.9756 Use & Care Manual

Kenmore clothes dryer user manual
Hide thumbs


Table of Contents
You can customize your cycles by selecting options.
GUARD e_90
WRINKLE GUARD ®90 helps smooth out wrinkles that form when
you cannot unload the dryer promptly at the end of a cycle.
During this option, the dryer periodically
starts and stops,
tumbling the load for 90 minutes.
Press WRINKLE GUARD ®90 to get up to 90 minutes of heat-
free, periodic tumbling at the end of a cycle.
Stop WRINKLE GUARD ® 90 at any time by pressing
WRINKLE GUARD ®90 or opening the dryer door.
WRINKLE GUARD ®90 is preset to OFF. The Auto Dry cycles
will retain the WRINKLE GUARD ®90 setting. For example, if
you select WRINKLE GUARD ®90 in the Normal cycle,
WRINKLE GUARD ®90 will be on the next time you select the
Normal cycle.
NOTE: WRINKLE GUARD ® 90 must be selected with a cycle in
order to work. If you do not select WRINKLE GUARD _ 90, the
dryer stops after cool down.
Cycle Signal
The Cycle Signal produces an audible sound when the drying
cycle is finished. Promptly removing clothes at the end of the
cycle reduces wrinkling.
Press CYCLE SIGNAL to turn the signal off.
NOTE: When WRINKLE GUARD _ 90 is selected and the Cycle
Signal is on, a tone sounds every 5 minutes until the clothes are
removed, or WRINKLE GUARD ®90 ends.
You can change Auto Cycles, Timed Cycles, Modifiers and
Options anytime before pressing Start.
Three short tones sound if an unavailable combination
selected. The last selection will not be accepted.
Cycles after pressing Start
1. Press STOP twice. This ends the current cycle.
2. Select the desired cycle and options.
3. Press and hold START. The dryer starts at the beginning of
the new cycle.
NOTE: If you do not press Start within 5 minutes of selecting the
cycle, the dryer automatically
shuts off.
and Options after pressing Start
You can change a Modifier or Option anytime before the selected
Modifier or Option begins.
1. Press STOP once.
2. Select the new Modifier and/or Option.
3. Press and hold START to continue the cycle.
NOTE: If you happen to press Stop twice, the program clears and
your dryer shuts down. Restart the selection process.
The dryer rack is shipped in place in your dryer. Remove and
discard any packing material before use.
Use the TUMBLE FREF M Non-Heated
Dryer Rack for items that
you do not want to tumble dry, such as sweaters.
To use the dryer rack
Do not remove the lint screen.
1. Open dryer door.
A. Front edge
2. Place dryer rack inside dryer drum, positioning the back wire
on the ledge of the inner dryer back panel. Push down on
front edge of dryer rack to secure over the lint screen.
A. Dryer rack front edge
B. Dryer back panel
3. Put the wet items on top of the rack. Leave space between
the items so air can reach all the surfaces.
NOTE: Do not allow items to hang over the edge of the rack.
4. Close the door.
5. Press the POWER button.
6. Select a timed cycle and temperature
(see following chart).
Items containing foam, rubber, or plastic must be dried on a
clothesline or by using the Air Only temperature
7. You may change the cycle time by pressing MORE TIME or
LESS TIME. Reset time as needed to complete drying. Refer
to the following table.
8. Press (and hold) START button (about 3 seconds).
NOTE: You must remove rack for normal tumbling.
Do not use
automatic cycles with the dryer rack.

Hide quick links:


Table of Contents

  Related Manuals for Kenmore 110.9756