Summary of Contents for GigaTera HR 85W
- Page 1 http://www.kmwgigatera.com Installation & Operation User Guide Product Installation & Operation User Guide Roadway Lighting 110W 150W...
- Page 2 『 』 Safety Precautions Installation This symbol is intended to remind the user the presence of actions and operation that may cause danger. Please read instructions carefully and follow the instructions to avoid any danger. This symbol is intended to represent precautions that the user should follow to prevent danger. WARNING Serious injury might result if the following precautions are not followed.
- Page 3 Street Light (HR) Installation & Operation User Guide The information in this document is subject to change without notice 1) Scope Overview This manual describes how to compose, install, and operate LED streetlamps. 2) LED Streetlamp Apparatus (LED Streetlight) A streetlamp is a lamp that is installed on the side of least four-lane roads to improve traffic safety of vehi- cles and civilians as well as traffic efficiency.
- Page 4 Street Light (HR) Installation & Operation User Guide The information in this document is subject to change without notice Precautions before Installation This installation manual is based on the assumption an Electronic Auto Switch is installed to each product. A product with an Electronic Auto Switch may look different from what it looks like in the brochure. Although, the other parts than the Electronic Auto Switch will be installed in the same manner.
-
Page 5: Detail Description
Street Light (HR) Installation & Operation User Guide The information in this document is subject to change without notice ① HR ② Converter Detail Description Item Purpose ① LED Streetlamp ② Converter Lamp and Brightness Sensor Power Supply Device (SMPS) Copyright 1991 ~ 2012 KMW, INC. - Page 6 Street Light (HR) Installation & Operation User Guide The information in this document is subject to change without notice ① HR ② Converter ③ Illumination Sensor Intensity Detail Description Item Purpose ① LED Streetlamp ② Converter Lamp and Brightness Sensor Power Supply Device (SMPS) Illumination Sensor In- Surrounding Brightness Based Automatic Power On/Off Function (Photo ③...
- Page 7 Street Light (HR) Installation & Operation User Guide The information in this document is subject to change without notice ① HR ② Converter ③ DCM Detail Description Item Purpose ① LED Streetlamp ② Converter Lamp and Brightness Sensor Power Supply Device (SMPS) ③...
- Page 8 Street Light (HR) Installation & Operation User Guide The information in this document is subject to change without notice ① HR ② Converter ③ Illumination Sensor Intensity ④ DCM Detail Description Item Purpose ① LED Streetlamp ② Converter Lamp and Brightness Sensor Power Supply Device (SMPS) ③...
- Page 9 Street Light (HR) Installation & Operation User Guide The information in this document is subject to change without notice STEP. 01 Put the product box on an even and flat surface and cut the box along the suture line with a cutter. Please make sure the cutter blade doesn't enter deep enough to scratch the product surface.
- Page 10 Street Light (HR) Installation & Operation User Guide The information in this document is subject to change without notice STEP. 04 As the sun rises from the east and sets to the west, you must direct the Brightness Sensor Receptacle to the north for normal operation of the product.
- Page 11 Street Light (HR) Installation & Operation User Guide The information in this document is subject to change without notice STEP. 07 The brightness sensor has a directional nature as seen in the following figure: Among the three connection parts, one is designed to be long and wide and the others short and narrow.
- Page 12 Street Light (HR) Installation & Operation User Guide The information in this document is subject to change without notice STEP. 10 Open the SMPS part from the main body for AC pow- er cable wiring. To begin with, use your thumb to push the latch lock- er upward and pull the lower part like the following figure: When you zoom in the image, the part that was hid-...
- Page 13 Street Light (HR) Installation & Operation User Guide The information in this document is subject to change without notice STEP. 13 Open the SMPS part and hang it on the hook before you start wiring. STEP. 14 Insert the AC power cable behind the arm like the fol- lowing figure: HR Model basically does not supply the AC power cable.
- Page 14 Street Light (HR) Installation & Operation User Guide The information in this document is subject to change without notice STEP. 16 Keep the lamp and the light pole so arranged that the AC power cable is not stuck between them be- fore you bond them together.
- Page 15 Street Light (HR) Installation & Operation User Guide The information in this document is subject to change without notice STEP. 19 Be sure to bond the AC power cable with the SMPS cable. At first, use the twister to connect the two cores of the white cable (N) with each other.
- Page 16 Street Light (HR) Installation & Operation User Guide The information in this document is subject to change without notice STEP. 22 Once the AC power cable is connected, arrange the internal wiring well and close the SMPS cover like the following figure: STEP.
- Page 17 Street Light (HR) Installation & Operation User Guide The information in this document is subject to change without notice STEP. 25 Remove the fixing bolts in front to lower the lamp by 5°. Push the lamp downward whiling aligning its first and third bolt holes with the corresponding light pole holes and bolt parts together for fixing like the following figure:...
- Page 18 RF & Microwave Products The Global Leading RF & LED Provider For America 1521 E. Orangethorpe Ave., Ste. A Fullerton, CA 92831 U.S.A +1.714.515.1100 sales@kmwgigatera.com For Non-America 183-6, Yeongcheon-ro, Dongtan-myeon, Hwaseong-si, Gyeonggi-do, Korea +82.31.370.8720 chriskim@kmw.co.kr...