ISHIDA Uni-5 User Manual
  1. Manuals
  2. Brands
  3. ISHIDA Manuals
  4. Scales
  5. Uni-5
  6. User manual

ISHIDA Uni-5 User Manual

Hide thumbs Also See for Uni-5:
Table of Contents

Advertisement

Quick Links

IMPORTANT
• Read this manual thoroughly, and do not perform installation,
operation, maintenance, or inspection unless you fully
understand all of the contents.
• Keep this manual in a safe place where you can refer to it
easily while installing, operating, and carrying out
maintenance or inspections.
User's Manual
Ver. 1.02
RS-61004-11 1.02

Advertisement

Table of Contents
loading

Related Manuals for ISHIDA Uni-5

Summary of Contents for ISHIDA Uni-5

  • Page 1 User’s Manual Ver. 1.02 IMPORTANT • Read this manual thoroughly, and do not perform installation, operation, maintenance, or inspection unless you fully understand all of the contents. • Keep this manual in a safe place where you can refer to it easily while installing, operating, and carrying out maintenance or inspections.
  • Page 2 © ISHIDA Co., Ltd. 2008 All rights are reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means mechanical, electronic, photocopying, recording, or otherwise without prior written permission of ISHIDA.
  • Page 3 Make sure that the initial screen is displayed. Press the [MODE] key on the key sheet. The Operation Mode screen appears. Then, press the [ADJUST] button on the screen The Adjustment Menu Select screen appears. UNI-5 User’s Manual 12- 1...
  • Page 4 DATE / TIME ADJUSTMENT Press the “TIME / DATE SET” field on the Adjustment Menu Select screen. The Time/Date Set screen appears. To change the date, enter a new date and press the “DATE” field. EXAMPLE 22 June, 2007 12-2 UNI-5 User’s Manual...
  • Page 5 To change the time, enter a new time and press the “TIME” field. EXAMPLE 13:50:00 To register new date and time, press the [SET] button. The confirmation screen appears. Then, press the [EXEC] button for execution. UNI-5 User’s Manual 12- 3...
  • Page 6 Press the “TOUCH PANEL” field on the Adjustment Menu Select screen. The Touch Panel screen appears. Press the [+] button on the upper left of the screen. Press the [+] button on the lower right of the screen. 12-4 UNI-5 User’s Manual...
  • Page 7 Chapter 12 ADJUSTMENT MODE Press the [SET] button to confirm calibration. UNI-5 User’s Manual 12- 5...
  • Page 8 Press the [-] or [+] button to adjust vertical brightnesses for the operator and customer displays. Press the [HORIZONTAL] button to change to the horizontal display check screen. The Display Check (Horizontal) screen appears. Press the [-] or [+] button to adjust vertical brightnesses for the operator and customer displays. 12-6 UNI-5 User’s Manual...

  • Page 9: Before Use

    Label size Label width: 30mm to 60mm Label length: 20mm to 150mm Number of label cassettes 7 cassettes Input/Output LAN 1 channel USB 1 channel CF 1 channel Drawer 2 channels Program store medium Flash ROM (32M bytes) UNI-5 User’s Manual...
  • Page 10 Chapter 1 BEFORE USE MODEL VARIATIONS Bench Type Pole Type Elevated Type Self-service Type UNI-5 User’s Manual...
  • Page 11 Chapter 1 BEFORE USE PART NAMES AND FUNCTIONS 1.3.1 FRONT VIEW (BENCH TYPE) 1.3.2 REAR VIEW (BENCH TYPE) UNI-5 User’s Manual...
  • Page 12 Used to issue a label. Used to jump to the top page. Used to enter tare weight. Used to jump to the end page. Used to escape from the current Used to reset a weigh to zero. mode. UNI-5 User’s Manual...
  • Page 13 Accurate measurements cannot be performed if it is not installed horizontally. 1.5.2 OPERATION PANEL ANGLE ADJUSTMENT (BENCH TYPE) To obtain a better view, adjust the angle of the operation panel within the range between 0 and 70 degrees. UNI-5 User’s Manual...

  • Page 14: Label / Receipt Roll Loading

    LABEL / RECEIPT ROLL LOADING Open the cover on the side of main body. Set a new roll around the roll holder and raise the roll stopper to fix the roll position. Thread the paper as shown in the figures below.. UNI-5 User’s Manual...
  • Page 15 For labels, fix the paper end with the backing paper stopper, and gently turn the winding bobbin counterclockwise until the label becomes tight. Slide the label/receipt guide to help smooth paper feeding according to the paper width. UNI-5 User’s Manual...
  • Page 16 For labels, press the [FEED] key on the key sheet to issue a label. At this time, confirm that the label is completely peeled off. Confirm that the backing paper is wound up smoothly. If the backing paper is wound up diagonally, check that the label is set correctly. UNI-5 User’s Manual...

  • Page 17: Removing The Weigh Platter

    When replacing the weigh platter onto the main body, engage the two hooks at the rear side of the platter and lower the platter so that the two pins on the bottom of the platter are inserted into holes of the rubber platter holders. UNI-5 User’s Manual...

  • Page 18: Precautions When Using Cleaning Fluids

    Do not give the victim anything to drink, and do not rinse the mouth. If vomiting occurs naturally, have the victim lean forward to reduce risk of aspiration. Keep the victim warm and seek medical attention. 1-10 UNI-5 User’s Manual...

  • Page 19: Turning On The Power

    Then, check that displayed date and time agree with current date and time, and press the [ENTER] button on the screen to proceed to the next step. Note: Refer to “Time/Date Set” menu in Adjust Mode when changing the date or time. 21-JUN-2007 11:13:38 After a while, the initial screen appears. UNI-5 User’s Manual 1-11...

  • Page 20: Performing Zero Adjustment

    1.9.2 PERFORMING ZERO ADJUSTMENT If the weight value is not zero on the initial screen, Press the [ZERO] key on the key sheet to perform zero weight adjustment. The “ZERO” indicator lights up and the weight value becomes zero. 1-12 UNI-5 User’s Manual...

  • Page 21: Getting Back To The Initial Screen

    1.9.3 GETTING BACK TO THE INITIAL SCREEN To get back to the initial screen from a Menu Select screen, press either the “SALES” field or the icon at the bottom right on the screen. The initial screen appears. UNI-5 User’s Manual 1-13...
  • Page 22 PLU No.6 “Roast Beef” When the product is preset as a traceable item, the traceability screen appears. See Chapter 4 for more details about traceability products. The selected PLU screen appears. Without Preset Tare Weight UNI-5 User’s Manual 2- 1...
  • Page 23 “TARE” field on the screen. EXAMPLE Tare weight “50g” See Chapter 5 for more details about temporary change operations. Put a product on the weigh platter. The weight is measured and the total price is calculated. UNI-5 User’s Manual...
  • Page 24 Press the [PRINT] key on the key sheet. The label is issued. Non-traceable products Traceable products When “AUTO” is set in the Print Mode, The label is automatically issued as soon as the weighing is stabilized. Non-traceable products Traceable products UNI-5 User’s Manual 2- 3...

  • Page 25: Weighing Fixed Price Products

    EXAMPLE PLU No.6 “Roast Beef” When the product is preset as a traceable item, the traceability screen appears. See Chapter 4 for more details about traceability products. The selected PLU screen appears. Without Preset Tare Weight UNI-5 User’s Manual...
  • Page 26 “TARE” field on the screen. EXAMPLE Tare weight “50g” See Chapter 5 for more details about temporary change operations. Put a product on the weigh platter. The weight is measured but the fixed price stays same. UNI-5 User’s Manual 2- 5...
  • Page 27 When “MANUAL” is set in the Print Mode, Press the [PRINT] key on the key sheet. Non-traceable products Traceable products When “AUTO” is set in the Print Mode, The label is automatically issued as soon as the weighing is stabilized. Non-traceable products Traceable products UNI-5 User’s Manual...

  • Page 28: Processing Fixed Price Products

    When the product is preset as a traceable item, the traceability screen appears. See Chapter 4 for more details about traceability products. The selected PLU screen appears. See Chapter 5 for more details about temporary change operations. UNI-5 User’s Manual 2- 7...
  • Page 29 Press the [PRINT] key on the key sheet to issue the labels. The label is issued. Non-traceable products Traceable products Remove the label. The next label is issued. Non-traceable products Traceable products Note: To stop printing, press the [PRINT] key again. UNI-5 User’s Manual...
  • Page 30 When the product is preset as a traceable item, the traceability screen appears. See Chapter 4 for more details about traceability products. The selected PLU screen appears. See Chapter 5 for more details about temporary change operations. UNI-5 User’s Manual 2- 9...
  • Page 31 Press the [PRINT] key on the key sheet to issue the labels. The label is issued. Non-traceable products Traceable products Remove the label. The next label is issued. Non-traceable products Traceable products Note: To stop printing, press the [PRINT] key again. 2-10 UNI-5 User’s Manual...
  • Page 32 When the product is preset as a traceable item, the traceability screen appears. See Chapter 4 for more details about traceability products. The selected product screen appears. Without Preset Tare Weight With Preset Tare Weight UNI-5 User’s Manual 2- 11...
  • Page 33 “TARE” field on the screen. EXAMPLE Tare weight “50g” See Chapter 5 for more details about temporary change operations. Put a product on the weigh platter. The weight is measured and the total price is calculated. 2-12 UNI-5 User’s Manual...
  • Page 34 Chapter 2 LABEL ISSUE Press a operator button on the screen to issue the label. EXAMPLE Operator “BETTY” The label is issued. UNI-5 User’s Manual 2- 13...
  • Page 35 EXAMPLE PLU No.6 “Roast Beef” When the product is preset as a traceable item, the traceability screen appears. See Chapter 4 for more details about traceability products. The selected product screen appears. Without Preset Tare Weight 2-14 UNI-5 User’s Manual...
  • Page 36 “TARE” field on the screen. EXAMPLE Tare weight “50g” See Chapter 5 for more details about temporary change operations. Put a product on the weigh platter. The weight is measured and the total price is calculated. UNI-5 User’s Manual 2- 15...
  • Page 37 Chapter 2 LABEL ISSUE Press a operator button on the screen to issue the label. EXAMPLE Operator “BETTY” The label is issued. 2-16 UNI-5 User’s Manual...
  • Page 38 When the product is preset as a traceable item, the traceability screen appears. See Chapter 4 for more details about traceability products. The selected PLU screen appears. See Chapter 5 for more details about temporary change operations. UNI-5 User’s Manual 2- 17...
  • Page 39 Chapter 2 LABEL ISSUE Press a operator button on the screen to issue the label. EXAMPLE Operator “BETTY” The label is issued. 2-18 UNI-5 User’s Manual...
  • Page 40 When the product is preset as a traceable item, the traceability screen appears. See Chapter 4 for more details about traceability products. The selected PLU screen appears. See Chapter 5 for more details about temporary change operations. UNI-5 User’s Manual 2- 19...
  • Page 41 Enter the fixed weight using the numeric keys on the key sheet and press the “FIXED WEIGHT” field. EXAMPLE Fixed weight “858g” Press a operator button on the screen to issue the label. EXAMPLE Operator “BETTY” The label is issued. 2-20 UNI-5 User’s Manual...
  • Page 42 Then, enter a desired PLU number using the numeric keys and press the [PLU] key on the key sheet, or simply press a preset key on the screen where a desired product is allocated. EXAMPLE Select PLU No.1 “Rib Steak”. UNI-5 User’s Manual 3- 1...
  • Page 43 Chapter 3 RECEIPT ISSUE The PLU screen appears. Weighing Unit Price PLU Put a product on the weigh platter. Press a button on the screen for the operator who has sold the product. EXAMPLE Select “Operator 002”. UNI-5 User’s Manual...
  • Page 44 Then, enter a desired PLU number using the numeric keys and press the [PLU] key on the key sheet, or simply press a preset key on the screen where a desired product is allocated. EXAMPLE Select PLU No.102 “Maine Lobster”. UNI-5 User’s Manual 3- 3...
  • Page 45 Press a button on the screen for the operator who has sold the product. EXAMPLE Select “Operator 002”. The subtotal for the selected operator is shown on the screen. Select a desired product category by pressing the corresponding field on the screen. EXAMPLE Select “Bakery” category. UNI-5 User’s Manual...
  • Page 46 EXAMPLE Select PLU No.201 “Live Wild Cherry Clam”. The PLU screen appears. Weighing Fixed Price PLU Put a product on the weigh platter. UNI-5 User’s Manual 3- 5...
  • Page 47 The PLU preset screen for the selected category appears. Then, enter a desired PLU number using the numeric keys and press the [PLU] key on the key sheet, or simply press a preset key on the screen where a desired product is allocated. UNI-5 User’s Manual...
  • Page 48 Select PLU No.4 “Pork Chops”. The PLU screen appears. Fixed Unit Price PLU Enter the weight using the numeric keys on the key sheet, and press the “Fixed Weight” field on the screen. EXAMPLE Weight “400g” UNI-5 User’s Manual 3- 7...
  • Page 49 The subtotal for the selected operator is shown on the screen. Press the subtotal field on the screen to display more detailed subtotal data. The detailed subtotal screen appears for confirmation of product registrations. Then, confirm that the detail of the transaction is correct. UNI-5 User’s Manual...
  • Page 50 Chapter 3 RECEIPT ISSUE Press the [PRINT] key on the key sheet to issue the receipt. UNI-5 User’s Manual 3- 9...
  • Page 51 Chapter 3 RECEIPT ISSUE The Subtotal screen appears for the settlement. 3-10 UNI-5 User’s Manual...
  • Page 52 Then, enter a desired PLU number using the numeric keys and press the [PLU] key on the key sheet, or simply press a preset key on the screen where a desired product is allocated. EXAMPLE Select PLU No.1 “Rib Steak”. UNI-5 User’s Manual 3- 11...
  • Page 53 Chapter 3 RECEIPT ISSUE The PLU screen appears. Weighing Unit Price PLU Put a product on the weigh platter. Press a button on the screen for the operator who has sold the product. EXAMPLE Select “Operator 002”. 3-12 UNI-5 User’s Manual...
  • Page 54 Then, enter a desired PLU number using the numeric keys and press the [PLU] key on the key sheet, or simply press a preset key on the screen where a desired product is allocated. EXAMPLE Select PLU No.102 “Maine Lobster”. UNI-5 User’s Manual 3- 13...
  • Page 55 Select “Operator 002”. The subtotal for the selected operator is shown on the screen. EXAMPLE Product registration by “Operator 001” Select a desired product category by pressing the corresponding field on the screen. EXAMPLE Select “Bakery” category. 3-14 UNI-5 User’s Manual...
  • Page 56 EXAMPLE Select PLU No.201 “Live Wild Cherry Clam”. The PLU screen appears. Weighing Fixed Price PLU Put a product on the weigh platter. UNI-5 User’s Manual 3- 15...
  • Page 57 Select “Operator 001”. The subtotal for the selected operator is shown on the screen. EXAMPLE Product registration by “Operator 002” Select a desired product category by pressing the corresponding field on the screen. EXAMPLE Select “Meat” category. 3-16 UNI-5 User’s Manual...
  • Page 58 Select PLU No.4 “Pork Chops”. The PLU screen appears. Fixed Unit Price PLU Enter the weight using the numeric keys on the key sheet, and press the “Fixed Weight” field on the screen. EXAMPLE Weight “400g” UNI-5 User’s Manual 3- 17...
  • Page 59 The subtotal for the selected operator is shown on the screen. Press the subtotal field on the screen to display more detailed subtotal data. The detailed subtotal screen appears for confirmation of product registrations. Then, confirm that the detail of the transaction is correct. 3-18 UNI-5 User’s Manual...
  • Page 60 Chapter 3 RECEIPT ISSUE Press the [PRINT] key on the key sheet to issue the receipt. The Subtotal screen appears for the settlement. UNI-5 User’s Manual 3- 19...
  • Page 61 Then, enter a desired PLU number using the numeric keys and press the [PLU] key on the key sheet, or simply press a preset key on the screen where a desired product is allocated. EXAMPLE Select PLU No.3 “Round Steak”. 10-3 The PLU screen appears. Weighing Unit Price PLU 3-20 UNI-5 User’s Manual...
  • Page 62 Put a product on the weigh platter. 10-5 Press a button on the screen for the operator who has sold the product. EXAMPLE Select “Operator 001”. 10-6 The subtotal for the selected operator is shown on the screen. UNI-5 User’s Manual 3- 21...
  • Page 63 Receipt issue by “Operator 001” Press the subtotal field on the screen to display more detailed subtotal data. The Subtotal screen appears for confirmation of product registrations. Press the [PRINT] key on the key sheet to issue the receipt. 3-22 UNI-5 User’s Manual...
  • Page 64 Chapter 3 RECEIPT ISSUE The Subtotal screen appears for the settlement. UNI-5 User’s Manual 3- 23...
  • Page 65 Note: To scroll the selection up or down, press the [ ] or [ ] keys on the key sheet. Press the [VOID] button on the screen. The confirmation screen appears. Then, press the [EXEC] button for execution. 3-24 UNI-5 User’s Manual...
  • Page 66 Chapter 3 RECEIPT ISSUE The selected item has been voided. Press the [PRINT] key on the key sheet to issue the receipt. Deleted by a dashed line UNI-5 User’s Manual 3- 25...
  • Page 67 Chapter 3 RECEIPT ISSUE The Subtotal screen appears for the settlement. 3-26 UNI-5 User’s Manual...
  • Page 68 Enter a desired PLU number using the numeric keys and press the [PLU] key on the key sheet, or simply press a preset key on the screen where the product is allocated. EXAMPLE PLU number “6”. When the product is preset as a traceable item, the Traceability screen appears. UNI-5 User’s Manual 4- 1...
  • Page 69 To refer to the previously processed traceability data, press the [LIST] button. The Traceability History screen appears. Then, press to select a desired data field. The selected data appears. Then, press the [SET] button. The selected PLU screen appears. Weighing Unit Price Products UNI-5 User’s Manual...
  • Page 70 Chapter 4 TRACEABILITY PRODUCTS Fixed Price Products Fixed Unit Price Products Weighing Fixed Price Products UNI-5 User’s Manual 4- 3...
  • Page 71 EXAMPLE PLU number “6”. When the product is preset as a traceable item, the Traceability screen appears. Then, confirm whether information on the screen is correct or not. When the data is correct, press the [SET] button. UNI-5 User’s Manual...
  • Page 72 If the data is not correct, press to select a desired data field. EXAMPLE Select “France”. EXAMPLE Change to “Argentina”. The data has been changed. To change the “FACTORY” data, press the corresponding field. Press to select a desired data field. UNI-5 User’s Manual 4- 5...
  • Page 73 The data has been changed. Then, press the [SET] button. When changing the lot data, press the “LOT” filed. The Traceability Lot Number Set screen appears. Change the lot number using the [ABC] [ERASE] and [BACK SPACE] buttons, and press the [BACK] button to finish. UNI-5 User’s Manual...

  • Page 74: Fixed Price Products

    Chapter 4 TRACEABILITY PRODUCTS The confirmation screen appears. Then, press the [SAVE] button to save the data. The Traceability screen appears. Then, press the [SET] button. The selected PLU screen appears. Weighing Unit Price Products Fixed Price Products UNI-5 User’s Manual 4- 7...
  • Page 75 Chapter 4 TRACEABILITY PRODUCTS Fixed Unit Price Products Weighing Fixed Price Products UNI-5 User’s Manual...
  • Page 76 Ensure that the selected PLU screen is displayed. Weighing Products Fixed Unit Price Products Enter a desired unit price using the numeric keys and press the “UNIT PRICE” or “FIXED UNIT PRICE” field. EXAMPLE “$3.80” Weighing Products UNI-5 User’s Manual 5- 1...
  • Page 77 Chapter 5 TEMPORARY CHANGE OPERATIONS Fixed Unit Price Products UNI-5 User’s Manual...
  • Page 78 FIXED PRICE CHANGE Ensure that the selected PLU screen is displayed. Fixed Price Products Weighing Fixed Price Products Enter a desired price using the numeric keys, and press the “FIXED PRICE” field. EXAMPLE “$3.80” Fixed Price Products UNI-5 User’s Manual 5- 3...
  • Page 79 Chapter 5 TEMPORARY CHANGE OPERATIONS Weighing Fixed Price Products UNI-5 User’s Manual...
  • Page 80 Ensure that the selected PLU screen is displayed. Weighing Unit Price Products Fixed Unit Price Products Enter a desired discount amount using the numeric keys, and press the “-$ (U/P)” field. EXAMPLE Discount amount “$1.00”. Weighing Unit Price Products UNI-5 User’s Manual 5- 5...
  • Page 81 Chapter 5 TEMPORARY CHANGE OPERATIONS Fixed Unit Price Products UNI-5 User’s Manual...
  • Page 82 Ensure that the selected PLU screen is displayed. Weighing Unit Price Products Fixed Unit Price Products Enter a desired discount percentage using the numeric keys on the key sheet, and press the “-% (U/P)” field. EXAMPLE Discount percentage “10%”. UNI-5 User’s Manual 5- 7...
  • Page 83 Chapter 5 TEMPORARY CHANGE OPERATIONS Fixed Unit Price Products UNI-5 User’s Manual...
  • Page 84 Ensure that the selected PLU screen is displayed. Fixed Price Products Weighing Fixed Price Products Enter a desired discount amount using the numeric keys, and press the “-$” field. EXAMPLE Discount amount “$1.00”. Fixed Price Products UNI-5 User’s Manual 5- 9...
  • Page 85 Chapter 5 TEMPORARY CHANGE OPERATIONS Weighing Fixed Price Products 5-10 UNI-5 User’s Manual...
  • Page 86 Ensure that the selected PLU screen is displayed. Fixed Price Products Weighing Fixed Price Products Enter a desired discount percentage using the numeric keys on the key sheet, and press the “-%” field. EXAMPLE Discount percentage “10%”. UNI-5 User’s Manual 5- 11...
  • Page 87 Chapter 5 TEMPORARY CHANGE OPERATIONS Weighing Fixed Price Products 5-12 UNI-5 User’s Manual...
  • Page 88 Ensure that the selected PLU screen is displayed. Fixed Price Products Enter a desired quantity using the numeric keys, and press the “PCS” field. EXAMPLE Quantity “2 pieces” To select a desired fix price mark, press the “PCS” field again. UNI-5 User’s Manual 5- 13...
  • Page 89 Chapter 5 TEMPORARY CHANGE OPERATIONS The Fix Price mark List screen appears. Then, select a desired mark by pressing the corresponding field. EXAMPLE Price mark “PC. PCS.” 5-14 UNI-5 User’s Manual...
  • Page 90 Press the [PRINT] key on the key sheet. The set number of labels will be issued. Note: To interrupt the issue of labels, press the [PRINT] key again. To continue the issue of labels, press the [PRINT] key again. UNI-5 User’s Manual 5- 15...
  • Page 91 Chapter 6 SELF-SERVICE OPERATIONS SELF-SERVICE OPERATIONS WEIGHING PRODUCTS Ensure that the initial screen is displayed. Select a desired product by pressing the corresponding button on the screen. EXAMPLE Select “Roast Beef” The selected product screen appears. UNI-5 User’s Manual 6- 1...
  • Page 92 Chapter 6 SELF-SERVICE OPERATIONS Put a product on the weigh platter. The weight is measured and the total price is calculated. Press the [LABEL PRINT] button on the screen to issue the label. The label is issued. UNI-5 User’s Manual...
  • Page 93 Select a desired product by pressing the corresponding button on the screen. EXAMPLE Select “Roast Beef” The selected product screen appears. Then, press the [LABEL PRINT] button on the screen to issue the label. The label is issued. UNI-5 User’s Manual 6- 3...
  • Page 94 The Accumulator (Input Number Accumulation) screen appears. Enter a desired PLU number and press the [PLU] key on the key sheet. EXAMPLE PLU number “6”. The Input Number Accumulation screen for the selected product appears. UNI-5 User’s Manual 7- 1...
  • Page 95 Then, press the [ACC] button on the screen. EXAMPLE Quantity “1 pc.”, Weight “169g”, Price “$0.84” The confirmation screen appears. Then, press the [EXEC] button on the screen. The registration has been completed. UNI-5 User’s Manual...
  • Page 96 Chapter 7 ACCUMULATOR MODE WEIGHING ACCUMULATION To get the Operation Menu Select screen, press the [MODE] key on the key sheet. Then, press the “ACC (Accumulator)” filed. To get the Weighing Accumulation screen, press the [WGT. ACC] tab. UNI-5 User’s Manual 7- 3...
  • Page 97 PLU number “6”. The Weighing Accumulation screen for the selected product appears. Put a product on the weigh platter and press the [ACC] button on the screen.. The confirmation screen appears. Then, press the [EXEC] button on the screen. UNI-5 User’s Manual...
  • Page 98 Chapter 7 ACCUMULATOR MODE Remove the product from the weigh platter. UNI-5 User’s Manual 7- 5...
  • Page 99 Chapter 7 ACCUMULATOR MODE MANUAL INPUT VOID To get the Operation Menu Select screen, press the [MODE] key on the key sheet. Then, press the “ACC (Accumulator)” filed. To get the Input Number Void screen, press the [NUM. VOID] tab. UNI-5 User’s Manual...
  • Page 100 Enter a quantity, weight, and price that are to be voided and press the corresponding fields for registration. Then, press the [VOID] button on the screen. EXAMPLE Quantity “1 pc.”, Weight “169g”, Price “$0.84” The confirmation screen appears. Then, press the [EXEC] button on the screen. UNI-5 User’s Manual 7- 7...
  • Page 101 Chapter 7 ACCUMULATOR MODE The registration has been completed. UNI-5 User’s Manual...
  • Page 102 Chapter 7 ACCUMULATOR MODE WEIGHING VOID To get the Operation Menu Select screen, press the [MODE] key on the key sheet. Then, press the “ACC (Accumulator)” filed. To get the Weighing Void screen, press the [WGT. VOID] tab. UNI-5 User’s Manual 7- 9...
  • Page 103 The Weighing Void screen for the selected product appears. Put a product on the weigh platter and press the [VOID] button on the screen.. The confirmation screen appears. Then, press the [EXEC] button on the screen. 7-10 UNI-5 User’s Manual...
  • Page 104 Chapter 7 ACCUMULATOR MODE Remove the product from the weigh platter. UNI-5 User’s Manual 7- 11...
  • Page 105 Then, press the “TOTAL ADJUST” filed. Enter a desired PLU number and press the [PLU] key on the key sheet. EXAMPLE PLU number “6”. The Total Adjust (Input Number Subtraction) screen for the selected product appears. UNI-5 User’s Manual 8- 1...
  • Page 106 Enter a quantity, weight, and price that are to be subtracted and press the corresponding fields for registration. Then, press the [SUB] button on the screen. EXAMPLE Quantity “1 pc.”, Weight “169g”, Price “$0.84” The confirmation screen appears. Then, press the [EXEC] button on the screen. The registration has been completed. UNI-5 User’s Manual...
  • Page 107 WEIGHING SUBTRACTION To get the Operation Menu Select screen, press the [MODE] key on the key sheet. Then, press the “TOTAL ADJUST” filed. To get the Total Adjust (Weighing Subtraction) screen, press the [WGT. SUB] tab. UNI-5 User’s Manual 8- 3...
  • Page 108 The Total Adjust (Weighing Subtraction) screen for the selected product appears. Put a product on the weigh platter and press the [SUB] button on the screen.. The confirmation screen appears. Then, press the [EXEC] button on the screen. UNI-5 User’s Manual...
  • Page 109 Chapter 8 TOTAL ADJUST MODE Remove the product from the weigh platter. UNI-5 User’s Manual 8- 5...
  • Page 110 MANUAL INPUT ADDITION To get the Operation Menu Select screen, press the [MODE] key on the key sheet. Then, press the “TOTAL ADJUST” filed. To get the Total Adjust (Input Number Addition) screen, press the [NUM. ADD] tab. UNI-5 User’s Manual...
  • Page 111 Enter a quantity, weight, and price that are to beaded and press the corresponding fields for registration. Then, press the [ADD] button on the screen. EXAMPLE Quantity “1 pc.”, Weight “169g”, Price “$0.84” The confirmation screen appears. Then, press the [EXEC] button on the screen. UNI-5 User’s Manual 8- 7...
  • Page 112 Chapter 8 TOTAL ADJUST MODE The registration has been completed. UNI-5 User’s Manual...
  • Page 113 WEIGHING ADDITION To get the Operation Menu Select screen, press the [MODE] key on the key sheet. Then, press the “TOTAL ADJUST” filed. To get the Total Adjust (Weighing Add) screen, press the [WGT. ADD] tab. UNI-5 User’s Manual 8- 9...
  • Page 114 The Total Adjust (Weighing Add) screen for the selected product appears. Put a product on the weigh platter and press the [ADD] button on the screen.. The confirmation screen appears. Then, press the [EXEC] button on the screen. 8-10 UNI-5 User’s Manual...
  • Page 115 Chapter 8 TOTAL ADJUST MODE Remove the product from the weigh platter. UNI-5 User’s Manual 8- 11...

  • Page 116: Total Mode

    Press the “PRODUCTION DAILY TOTAL” filed. The Daily Total screen appears. To obtain the Hourly Total screen, press the [HOUR.] tab. To change the pages, press the [ ] or [ ] button on the screen. UNI-5 User’s Manual 9- 1...
  • Page 117 To change the pages, press the [ ] or [ ] button on the screen. To obtain the Designated Item Total screen, press the [ITEM] tab. Enter a desired PLU number using the numeric keys and press the [PLU] key on the key sheet. UNI-5 User’s Manual...
  • Page 118 ABC PCS Analysis is performed in descending quantity order. Z PRICE Analysis is performed in ascending price order. Z WEIGHT Analysis is performed in ascending weight order. Z PCS Analysis is performed in ascending quantity order. UNI-5 User’s Manual 9- 3...
  • Page 119 To change the pages, press the [ ] or [ ] button on the screen. To obtain total for the day-of-the week, press a desired day-of-the week tab. To change the pages, press the [ ] or [ ] button on the screen. UNI-5 User’s Manual...
  • Page 120 Chapter 9 TOTAL MODE UNI-5 User’s Manual 9- 5...
  • Page 121 To change the pages, press the [ ] or [ ] button on the screen. To obtain total for each group, press the [GROUP] tab on the screen. To change the pages, press the [ ] or [ ] button on the screen. UNI-5 User’s Manual...
  • Page 122 ABC PCS Analysis is performed in descending quantity order. Z PRICE Analysis is performed in ascending price order. Z WEIGHT Analysis is performed in ascending weight order. Z PCS Analysis is performed in ascending quantity order. UNI-5 User’s Manual 9- 7...
  • Page 123 The Traceability Item screen appears. To change the pages, press the [ ] or [ ] button on the screen. To obtain Traceability Total screen, press the [DETAIL] button on the screen. The Traceability Total screen appears. UNI-5 User’s Manual...
  • Page 124 Chapter 9 TOTAL MODE PRESET REPORT PRINTING Press the “PRESET REPORT” filed. The Preset Report screen appears. Select desired reports by pressing the corresponding fields. Press the [STRAT] button to issue selected join reports. UNI-5 User’s Manual 9- 9...
  • Page 125 The second page of the Menu Select screen appears. To obtain the Total Clear screen, press the “TOTAL CLEAR” field on the screen. The Total Clear screen appears. Select desired reports to be cleared by pressing the corresponding fields. 9-10 UNI-5 User’s Manual...
  • Page 126 Chapter 9 TOTAL MODE Press the [EXEC] button. The confirmation screen appears. Then, press the [EXEC] button on the screen for execution. UNI-5 User’s Manual 9- 11...

  • Page 127: Program Mode

    Press the [MODE] key on the key sheet. The Operation Menu Select screen appears. Then, press the [PROGRAM] button on the screen. The Program Menu Select screen appears. To change the pages, press the [ ] or [ ] button on the screen. 10-1 UNI-5 User’s Manual...
  • Page 128 Chapter 10 PROGRAM MODE 10-2 UNI-5 User’s Manual...
  • Page 129 Chapter 10 PROGRAM MODE Note: To exit the Program Mode, press the [ESC] (Escape) key on the key sheet. 10-3 UNI-5 User’s Manual...
  • Page 130 To change the pages, press the [ ] or [ ] button on the screen Press to select a desired field. Then, press the [DETAIL] button on the screen. EXAMPLE Select “Roast Beef”. The Item Detail screen appears. To edit the PLU name, press the [EDIT] button on the screen. 10-4 UNI-5 User’s Manual...
  • Page 131 Edit a text according to the procedure explained in Appendix “Text Editing”. Ensure that the first sales related screen is displayed. Sales Mode: Weighing Product Sales Mode: Fixed Price Product Sales Mode: Weighing Fixed Price Product 10-5 UNI-5 User’s Manual...
  • Page 132 Enter a fixed weight, and press this field. FIXED WEIGHT Enter a tare weight, and press this field. TARE UNDER WEIGHT Enter a lower weight limit, and press this field. UPPER WEIGHT Enter a upper weight limit, and press this field. 10-6 UNI-5 User’s Manual...
  • Page 133 POINT 0: Weight TYPE 1: Fixed weight POINTS Enter a desired number and press this field Press the [MESSAGE] tab to select the message related screen. Press to select a desired field. EXAMPLE “Extra Message 1”. 10-7 UNI-5 User’s Manual...
  • Page 134 The Extra Message List screen appears. Then, press to select a desired field. EXAMPLE “Extra Message BB”. Press the [IMAGE] tab to select the image related screen. Press to select a desired field. EXAMPLE Select a desired image for “Image 1”. 10-8 UNI-5 User’s Manual...
  • Page 135 Select “Image No.8”. Select whether or not to print Safe handling Image by pressing a desired field. 11-1 Press the [PRINT] tab to select the print related screen. 11-2 Press the [First Label Format No.] button. 10-9 UNI-5 User’s Manual...
  • Page 136 Press the [<] or [>] button to select whether or not to print the second labels. SECOND LABEL PRINT 1: YES 2: NO Note: The same procedure applies to the Second Label Format Number setting . 10-10 UNI-5 User’s Manual...
  • Page 137 Select whether or not to print the Use-By Date. UB DATE PRINT This field is available only when “Yes” is selected in “UB DATE UB DATE DATA PRINT”. Enter the number of hours and press this field 10-11 UNI-5 User’s Manual...
  • Page 138 Press this field to get the Barcode Type screen and press to select one of the PLU types. BARCODE TYPE Press this field to get the Barcode Format screen and press to select one of the barcode formats. 10-12 UNI-5 User’s Manual...
  • Page 139 “Department No.” field after a numeric entry. Pressing this field displays the Group List. Set the desired group simply by pressing the field on the list, or GROUP No. pressing the “Group No.” field after a numeric entry. 10-13 UNI-5 User’s Manual...
  • Page 140 To change the pages, press the [ ] or [ ] button on the screen. Create a new campaign file by entering a campaign number and pressing the [PLU] key on the key sheet. EXAMPLE Campaign number “2”. The confirmation screen appears. Then, press the [ENTER] button. 10-14 UNI-5 User’s Manual...
  • Page 141 The designated Campaign Data List screen appears. Enter the campaign start date and press the “Start Date” display field. . EXAMPLE Start date "June 25, 2007” Enter the start time and press the “Start Time” display field. . EXAMPLE Start time "08:00” 10-15 UNI-5 User’s Manual...
  • Page 142 Enter the campaign end date and press the “End Date” display field. . EXAMPLE End date "June 27, 2007” Enter the end time and press the “End Time” display field. EXAMPLE End time "21:00” Press the [CALL] button to call up Item List screens 10-16 UNI-5 User’s Manual...
  • Page 143 EXAMPLE PLU number “4” The Campaign Data List screen appears. Then, press the [CALL] button again when selecting the next item. The pop-up list appears. Then, press to select a desired field. EXAMPLE Percent discount “-%” 10-17 UNI-5 User’s Manual...
  • Page 144 Chapter 10 PROGRAM MODE Enter a numeric value and press the “Markdown Price” field for registration. EXAMPLE Repeat steps 9 through 12 for further registration. Then, press the Return button to finalize this procedure. The Campaign List screen appears. 10-18 UNI-5 User’s Manual...
  • Page 145 Press the "OPERATORS” field on the Program Menu Select screen. The Operator List screen appears. To create a new operator, enter the operator number and press the [PLU] key on the key sheet. EXAMPLE Operator number “7”. The confirmation screen appears. Press the [ENTER] button. 10-19 UNI-5 User’s Manual...
  • Page 146 Edit a text according to the procedures described in Appendix “Text Editing”. Press the [ESC] key on the key sheet to escape from text editing mode. The confirmation screen appears. Then, press the [SAVE] button to save the data. 10-20 UNI-5 User’s Manual...
  • Page 147 Chapter 10 PROGRAM MODE The edited text has been registered. Press the Return button to finalize this procedure. 10-21 UNI-5 User’s Manual...
  • Page 148 Chapter 10 PROGRAM MODE 10.5 PRESET KEY REGISTRATION 10.5.1 SETTING PRESET FUNCTIONS Press the “PRESET KEY” field on the screen. The Preset Key (Panel) screen appears. Ensure that the [SET] button is selected. 10-22 UNI-5 User’s Manual...
  • Page 149 Chapter 10 PROGRAM MODE Press a desired button to which a preset function will be assigned. Available functions are listed on the screens. To change the pages, press the [ ] or [ ] button on the screen. 10-23 UNI-5 User’s Manual...
  • Page 150 Press to select the desired function on the list, and press the [SET] button. EXAMPLE Select PLU function. The Item List screen appears. Then, press to select a desired field. EXAMPLE Select PLU No.2. The selected PLU has been assigned. 10-24 UNI-5 User’s Manual...
  • Page 151 Chapter 10 PROGRAM MODE Repeat steps 4 through 8 for more registrations. 10-25 UNI-5 User’s Manual...

  • Page 152: Assigning Images On The Preset Keys

    ASSIGNING IMAGES ON THE PRESET KEYS Press the “PRESET KEY” field on the screen. The Preset Key (Panel) screen appears. Press the [IMAGE] button. Press a desired preset key where the function is already assigned. EXAMPLE Select “Roast Beef” 10-26 UNI-5 User’s Manual...
  • Page 153 Chapter 10 PROGRAM MODE The Image List screen appears. Press to select a desired image. EXAMPLE Image No.3 The image has been assigned. Repeat steps 4 through 7 for more registrations. 10-27 UNI-5 User’s Manual...

  • Page 154: Coloring Preset Keys

    Press the “PRESET KEY” field on the screen. The Preset Key (Panel) screen appears. Press the [COLOR] button. Then, ensure that “Back Color” is selected. Press to select a desired preset key. EXAMPLE Select “Roast Beef” 10-28 UNI-5 User’s Manual...
  • Page 155 The Preset Key (Color) screen appears. Then, press to select a desired color. Selected color has been given to the background of the key. Press the [BACK COLOR] button to change to the [FORE COLOR] button. Press to select a desired preset key. EXAMPLE Select “Roast Beef” 10-29 UNI-5 User’s Manual...
  • Page 156 Chapter 10 PROGRAM MODE The Preset Key (Color) screen appears. Then, press to select a desired color. Selected color has been given to the foreground of the key. Repeat steps 4 through 10 for more registrations. 10-30 UNI-5 User’s Manual...

  • Page 157: Changing Preset Key Sizes

    CHANGING PRESET KEY SIZES Press the “PRESET KEY” field on the screen. The Preset Key (Panel) screen appears. Press the [SIZE] button, and ensure that “SMALL” is selected. Press the [SMALL] button to change to the [MIDDLE] button. 10-31 UNI-5 User’s Manual...
  • Page 158 Press the [MIDDLE] button to change to the [LARGE] button. Change the size of a desired key. EXAMPLE Change to the middle size of the “Roast Beef” key. Ensure that the [MIDDLE] button is selected. Press the “Roast Beef” key. 10-32 UNI-5 User’s Manual...
  • Page 159 Change the size of a desired key. EXAMPLE Change to the large size of the “Roast Beef” key. Ensure that the [LARGE] button is selected. Press the “Roast Beef” key. Repeat steps 3 through 4-2 for more registrations. 10-33 UNI-5 User’s Manual...

  • Page 160: Editing Preset Key Names

    EDITING PRESET KEY NAMES Press the “PRESET KEY” field on the screen. The Preset Key (Panel) screen appears. Press to select the [EDIT] button. Press to select a desired preset key. EXAMPLE Select the [Roast Beef] key. 10-34 UNI-5 User’s Manual...
  • Page 161 Edit a desired text according to the procedures described in Appendix “Text Editing”. EXAMPLE “Beef Fillet”. To finalize the editing, press the [ESC] key on the key sheet. The confirmation screen appears. Then, press the [SAVE] button to save the data. 10-35 UNI-5 User’s Manual...
  • Page 162 Chapter 10 PROGRAM MODE The edited text has been registered. Repeat steps 4 through 8 for more registrations. 10-36 UNI-5 User’s Manual...

  • Page 163: Confirming Preset Key Data

    Press the “PRESET KEY” field on the screen. The Preset Key (Panel) screen appears. Press to select the [DATA] button. Press a desired preset key. The related data is displayed on the button. EXAMPLE “Beef Fillet” and the PLU No.6 10-37 UNI-5 User’s Manual...

  • Page 164: Deleting Preset Keys

    The Preset Key (Panel) screen appears. Ensure that the [SET] button is selected. Press a desired preset key to be deleted. EXAMPLE Delete the [Roast Beef] key”. The Function List screen appears, and the assigned function field is highlighted. 10-38 UNI-5 User’s Manual...
  • Page 165 Chapter 10 PROGRAM MODE Press to select the “NO” field, and press the [SET] button. The selected key has been deleted. Repeat steps 3 through 6 for more deletions. 10-39 UNI-5 User’s Manual...

  • Page 166: Membrane Keys

    Press the “PRESET KEY” field on the screen. The Preset Key (Panel) screen appears. Then, press the [MEMBRANE] tab. The Preset Key (Membrane) screen appears. Press to select a desired membrane key to which the preset data is assigned. 10-40 UNI-5 User’s Manual...
  • Page 167 The Function List screen appears. Select a desired function to be assigned by pressing the corresponding field, and press the [SET] button. EXAMPLE Select “PLU” The Item List screen appears. Then, press to select a desired field. EXAMPLE PLU No.5 10-41 UNI-5 User’s Manual...
  • Page 168 Chapter 10 PROGRAM MODE The selected PLU has been assigned to the selected membrane key. 10-42 UNI-5 User’s Manual...
  • Page 169 When creating a message other than the first one, enter a desired message number using the numeric keys and press the [PLU] key on the key sheet. XAMPLE Message number “2”. The confirmation screen appears. Then, press the [ENTER] button. 10-43 UNI-5 User’s Manual...
  • Page 170 Edit a desired message according to the procedures described in Appendix “Text Editing”. Press the [ESC] key on the key sheet to escape from text editing mode. The confirmation screen appears. Then, press the [SAVE] button to save the data. 10-44 UNI-5 User’s Manual...
  • Page 171 0: Fast SPEED 1: Medium 2: Slow DISPLAY COUNT Enter a display count data and press this field. Press the [IMAGE] tab. Then, the Advertisement Message (Image) screen appears. When setting an image, press a desired field. 10-45 UNI-5 User’s Manual...
  • Page 172 Press to select a desired field and press the [SET] button. The selected image has been assigned in the designated field. Repeat steps 7 through 9 for more registrations. Then, press the Return button to finalize this procedure. The edited message has been registered. 10-46 UNI-5 User’s Manual...
  • Page 173 Press the “STORE NAME” field on the Program Menu Select screen. The default store data screen appears. When changing the store data, press the [EDIT] button. The Store Name Edit screen appears. Edit a text according to the procedures described in Appendix “Text Editing”. 10-47 UNI-5 User’s Manual...
  • Page 174 Press the [ESC] key on the key sheet to escape from text editing mode. The confirmation screen appears. Then, press the [SAVE] button. The store name has been changed. Press to select the address field line and press the [EDIT] button. The Store Address Edit screen appears. 10-48 UNI-5 User’s Manual...
  • Page 175 Edit a text according to the procedures described in Appendix “Text Editing”. Press the [ESC] key on the key sheet to escape from text editing mode. The confirmation screen appears. Then, press the [SAVE] button. The store address has been changed. 10-49 UNI-5 User’s Manual...

  • Page 176: Creating New Store Data

    Press the “STORE NAME” field on the Program Menu Select screen. The default store data screen appears. When creating a new store data, enter the desired store number and press the [PLU] key. EXAMPLE Store number “1” The confirmation screen appears. Then, press the [ENTER] button. 10-50 UNI-5 User’s Manual...
  • Page 177 Edit a text according to the procedures described in Appendix “Text Editing”. Press the [ESC] key on the key sheet to escape from text editing mode. The confirmation screen appears. Then, press the [SAVE] button. The store name has been registered 10-51 UNI-5 User’s Manual...
  • Page 178 The Store Address Edit screen appears. Edit a text according to the procedures described in Appendix “Text Editing”. Press the [ESC] key on the key sheet to escape from text editing mode. The confirmation screen appears. Then, press the [SAVE] button. 10-52 UNI-5 User’s Manual...
  • Page 179 Chapter 10 PROGRAM MODE The store address has been registered. Enter a desired store number as a default store data and press the “Printer 1” or “Printer 2” display field. EXAMPLE Set the store number “1” for printer #1. 10-53 UNI-5 User’s Manual...
  • Page 180 CREATING NEW DEPARTMENT NAMES Press the "Department” field on the Program Menu Select screen. The Department List screen appears. Then, press the [NEW] button. The confirmation screen appears. Then, press the [ENTER] button. The Department Name Edit screen appears. 10-54 UNI-5 User’s Manual...
  • Page 181 The confirmation screen appears. Then, press the [SAVE] button. The edited text has been registered. When creating more department names, enter a desired department number using the numeric keys and press the [PLU] key on the key sheet. EXAMPLE Department number “2”. 10-55 UNI-5 User’s Manual...
  • Page 182 The Department Name Edit screen appears. Edit a text according to the procedures described in Appendix “Text Editing”. Press the [ESC] key on the key sheet to escape from text editing mode. The confirmation screen appears. Then, press the [SAVE] button. 10-56 UNI-5 User’s Manual...
  • Page 183 Chapter 10 PROGRAM MODE The edited text has been registered. Repeat steps 8 through 12 for more registrations. 10-57 UNI-5 User’s Manual...

  • Page 184: Changing Exisiting Department Names

    Press the "Department” field on the Program Menu Select screen. The Department List screen appears. When changing an existing data, press to select a desired field. The Department Name Edit screen appears for the selected department. 10-58 UNI-5 User’s Manual...
  • Page 185 Press the [ESC] key on the key sheet to escape from text editing mode. The confirmation screen appears. Then, press the [SAVE] button. The edited text has been registered. Repeat steps 3 through 7 for more registrations. 10-59 UNI-5 User’s Manual...
  • Page 186 CREATING NEW GROUP NAMES Press the "Group” field on the Program Menu Select screen. The Group List screen appears. Then, press the [NEW] button. The confirmation screen appears. Then, press the [ENTER] button. The Group Name Edit screen appears. 10-60 UNI-5 User’s Manual...
  • Page 187 The confirmation screen appears. Then, press the [SAVE] button. The edited text has been registered. When creating more group names, enter a desired group number using the numeric keys and press the [PLU] key on the key sheet. EXAMPLE Group number “2”. 10-61 UNI-5 User’s Manual...
  • Page 188 Chapter 10 PROGRAM MODE The confirmation screen appears. Then, press the [ENTER] button. The Group Name Edit screen appears. Repeat steps 5 through 9 for more registrations. 10-62 UNI-5 User’s Manual...

  • Page 189: Changing Exisiting Group Names

    CHANGING EXISITING GROUP NAMES Press the "Group” field on the Program Menu Select screen. The Group List screen appears. When changing an existing data, press to select a desired field. The Group Edit screen appears for the selected group 10-63 UNI-5 User’s Manual...
  • Page 190 Press the [ESC] key on the key sheet to escape from text editing mode. The confirmation screen appears. Then, press the [SAVE] button. The edited text has been registered. Repeat steps 3 through 7 for more registrations. 10-64 UNI-5 User’s Manual...
  • Page 191 Press the "Cooking Instruction” field on the Program Menu Select screen. The Cooking Time List screen appears. Then, press the [NEW] button. The confirmation screen appears. Then, press the [ENTER] button. The Cooking Time Edit screen appears. 10-65 UNI-5 User’s Manual...
  • Page 192 The confirmation screen appears. Then, press the [SAVE] button. The edited text has been registered. Enter a numeric value for each filed using the numeric keys and press the corresponding field for registration. EXAMPLE Base time “35 minutes” 10-66 UNI-5 User’s Manual...
  • Page 193 [PLU] key on the key sheet. EXAMPLE Cooking instruction number “2”. The confirmation screen appears. Then, press the [ENTER] button. The Cooking Time Edit screen appears. Repeat steps 5 through 10 for more registrations. 10-67 UNI-5 User’s Manual...

  • Page 194: Changing Exisiting Instructions

    Press the "Cooking Instruction” field on the Program Menu Select screen. The Cooking Time List screen appears. When changing an existing data, press to select a desired field and press the [DETAIL] button. The Cooking Time Edit screen appears for the selected instruction 10-68 UNI-5 User’s Manual...
  • Page 195 Press the [ESC] key on the key sheet to escape from text editing mode. The confirmation screen appears. Then, press the [SAVE] button. The edited text has been registered. Repeat steps 3 through 7 for more registrations. 10-69 UNI-5 User’s Manual...
  • Page 196 The Nutrition List screen appears. Then, press the [NEW] button. The confirmation screen appears. Then, press the [ENTER] button. The Nutrition Data Programming screen for the selected nutrition number appears. When creating a text for “Serving Size”, press the [EDIT] button. 10-70 UNI-5 User’s Manual...
  • Page 197 Press the [ESC] key on the key sheet to escape from text editing mode. The confirmation screen appears. Then, press the [SAVE] button. The edited text has been registered. Then, enter a nutrition data for each field using the numeric keys and press the corresponding field for registration. 10-71 UNI-5 User’s Manual...
  • Page 198 When creating more nutrition data, enter a desired nutrition number using the numeric keys and press the [PLU] key on the key sheet. EXAMPLE Nutrition number “2”. The confirmation screen appears. Then, press the [ENTER] button. Repeat steps 4 through 9 for more registrations. 10-72 UNI-5 User’s Manual...

  • Page 199: Changing Existing Nutrition Data

    Press the "Nutrition (USA)” field on the Program Menu Select screen. The Nutrition List screen appears. Select a desired nutrition number. EXAMPLE Nutrition number “2”. or press the [PLU] key on the key sheet after a numeric entry. 10-73 UNI-5 User’s Manual...
  • Page 200 The Nutrition Data Programming screen for the selected nutrition number appears. When changing a text for “Serving Size”, press the [EDIT] button. The Nutrition Edit screen appears. Edit a text according to the procedures described in Appendix “Text Editing”. 10-74 UNI-5 User’s Manual...
  • Page 201 The edited text has been registered. When necessary, enter a nutrition data for each field using the numeric keys and press the corresponding field for registration. Press the Return button after making necessary changes. Repeat steps 3 through 10 for more registrations. 10-75 UNI-5 User’s Manual...
  • Page 202 Press the "Extra Message” field on the Program Menu Select screen. The Extra Message List screen appears. Then, press the [NEW] button. The confirmation screen appears. Then, press the [ENTER] button. The Extra Message Edit screen appears. 10-76 UNI-5 User’s Manual...
  • Page 203 The confirmation screen appears. Then, press the [SAVE] button. The edited text has been registered. When creating more messages, enter a desired message number using the numeric keys and press the [PLU] key on the key sheet. EXAMPLE Message number “2”. 10-77 UNI-5 User’s Manual...
  • Page 204 Chapter 10 PROGRAM MODE The confirmation screen appears. Then, press the [ENTER] button. Repeat steps 4 through 8 for more registrations. 10-78 UNI-5 User’s Manual...

  • Page 205: Changing Exisiting Messages

    Press the "Extra Message” field on the Program Menu Select screen. The Extra Message List screen appears. Select a desired message number. EXAMPLE Message number “2”. Press a desired field, or press the [PLU] key on the key sheet after a numeric entry. 10-79 UNI-5 User’s Manual...
  • Page 206 Edit a text according to the procedures described in Appendix “Text Editing”. Press the [ESC] key on the key sheet to escape from text editing mode. The confirmation screen appears. Then, press the [SAVE] button. Repeat steps 3 through 7 for more registrations. 10-80 UNI-5 User’s Manual...
  • Page 207 Press the "Coupon Message” field on the Program Menu Select screen. The Coupon Message List screen appears. Then, press the [NEW] button. The confirmation screen appears. Then, press the [ENTER] button. The Coupon Message Edit screen appears. 10-81 UNI-5 User’s Manual...
  • Page 208 The confirmation screen appears. Then, press the [SAVE] button. The edited text has been registered. When creating more messages, enter a desired message number using the numeric keys and press the [PLU] key on the key sheet. EXAMPLE Message number “2”. 10-82 UNI-5 User’s Manual...
  • Page 209 Chapter 10 PROGRAM MODE The confirmation screen appears. Then, press the [ENTER] button. Repeat steps 4 through 8 for more registrations. 10-83 UNI-5 User’s Manual...
  • Page 210 Press the "Extra Message” field on the Program Menu Select screen. The Coupon Message List screen appears. Select a desired message number. EXAMPLE Message number “2”. Press a desired field, or press the [PLU] key on the key sheet after a numeric entry. 10-84 UNI-5 User’s Manual...
  • Page 211 Edit a text according to the procedures described in Appendix “Text Editing”. Press the [ESC] key on the key sheet to escape from text editing mode. The confirmation screen appears. Then, press the [SAVE] button. Repeat steps 3 through 7 for more registrations. 10-85 UNI-5 User’s Manual...
  • Page 212 Press the "POP Message” field on the Program Menu Select screen. The message list screen appears. Enter a desired message number and press the [PLU] key on the key sheet. EXAMPLE Message number “7”. The confirmation screen appears. Then, press the [ENTER] button. 10-86 UNI-5 User’s Manual...
  • Page 213 P Press the [ESC] key on the key sheet to escape from text editing mode. The confirmation screen appears. Then, press the [SAVE] button. The edited text has been registered. Repeat steps 3 through 6 for more registrations. 10-87 UNI-5 User’s Manual...
  • Page 214 When changing a tax system, press to select a desired field. ITEM DESCRIPTION TAX TYPE Press to select one of tax types. Exclusive tax Inclusive tax Tax exemption TAX RATE Enter a numeric value and press this field. 10-88 UNI-5 User’s Manual...
  • Page 215 Press the "Scheme Table” field on the Program Menu Select screen. The Scheme Table screen appears. Then, press the [NEW] button. The confirmation screen appears. Then, press the [ENTER] button. The Scheme Table Detail (Basic) screen appears. Then, press the [EDIT] button. 10-89 UNI-5 User’s Manual...
  • Page 216 Edit a text according to the procedures described in Appendix “Text Editing”. Press the [ESC] key on the key sheet to escape from text editing mode. The confirmation screen appears. Then, press the [SAVE] button. The edited text has been registered. 10-90 UNI-5 User’s Manual...
  • Page 217 Enter a numeric value and press the corresponding field. WEIGHT Enter a numeric value and press the corresponding field. PASSPORT LOT START Enter a numeric value and press this field. PASSPORT GTIN START Enter a numeric value and press this field. 10-91 UNI-5 User’s Manual...
  • Page 218 When creating more tables, enter a desired table number using the numeric keys and press the [PLU] key on the key sheet. EXAMPLE Table number “2”. The confirmation screen appears. Then, press the [ENTER] button. Repeat steps 4 through 9 for more registrations. 10-92 UNI-5 User’s Manual...
  • Page 219 Press the "Scheme Table” field on the Program Menu Select screen. The Scheme Table screen appears. Select a desired table number by pressing the corresponding field. EXAMPLE Table number “2”. or press the [PLU] key on the key sheet after a numeric entry. 10-93 UNI-5 User’s Manual...
  • Page 220 Press to select whether or not to control the weight limit. 0: No 1: Yes DATE LIMIT CONTROL Press to select whether or not to control the date limit. 0: No 1: Yes LOSS % Enter a numeric value and press this field 10-94 UNI-5 User’s Manual...
  • Page 221 PASSPORT LOT START Enter a numeric value and press this field. PASSPORT GTIN START Enter a numeric value and press this field. When changing the table name, press the [EDIT] button. The Scheme Table Edit screen appears. 10-95 UNI-5 User’s Manual...
  • Page 222 Press the [ESC] key on the key sheet to escape from text editing mode. The confirmation screen appears. Then, press the [SAVE] button. The edited text has been registered. Then, press the Return button. The Scheme Table screen appears. Repeat steps 3 through 11 for more registrations. 10-96 UNI-5 User’s Manual...
  • Page 223 GEN TABLE REGISTRATION Press the "GEN Table” field on the Program Menu Select screen. The GEN Table screen appears. Select a desired GEN table by pressing the corresponding field. Enter a numeric value and press the corresponding field. 10-97 UNI-5 User’s Manual...
  • Page 224 The GEN Table Edit screen appears. Edit a text according to the procedures described in Appendix “Text Editing”. Press the [ESC] key on the key sheet to escape from text editing mode. The confirmation screen appears. Then, press the [SAVE] button. 10-98 UNI-5 User’s Manual...
  • Page 225 Chapter 10 PROGRAM MODE The edited text has been registered. Repeat steps 3 through 9 for more registrations. 10-99 UNI-5 User’s Manual...
  • Page 226 Press the "Lookup Table” field on the Program Menu Select screen. The Lookup Table screen appears. Then, press the [NEW] button. The confirmation screen appears. Then, press the [ENTER] button. The Lookup Table Data List screen appears. Then, press the [EDIT] button. 10-100 UNI-5 User’s Manual...
  • Page 227 Edit a text according to the procedures described in Appendix “Text Editing”. Press the [ESC] key on the key sheet to escape from text editing mode. The confirmation screen appears. Then, press the [SAVE] button. The edited text has been registered. Then, press the [NEW] button. 10-101 UNI-5 User’s Manual...
  • Page 228 The Lookup Data Table Edit screen appears. Edit a text according to the procedures described in Appendix “Text Editing”. Press the [ESC] key on the key sheet to escape from text editing mode. The confirmation screen appears. Then, press the [SAVE] button. 10-102 UNI-5 User’s Manual...
  • Page 229 When registering the next data text, enter the data number and press the [PLU] key on the key sheet. EXAMPLE Data number “2”. The confirmation screen appears. Then, press the [ENTER] button. The Lookup Data Table Edit screen appears. Edit a text according to the procedures described in Appendix “Text Editing”. 10-103 UNI-5 User’s Manual...
  • Page 230 The confirmation screen appears. Then, press the [SAVE] button. The edited text has been registered. Repeat steps 14 through 18 for more data registrations. Press the Return button to return to the Lookup Table screen. The Lookup Table screen appears. 10-104 UNI-5 User’s Manual...
  • Page 231 The confirmation screen appears. Then, press the [ENTER] button. The Lookup Table Data List screen appears. Then, press the [EDIT] button. The Lookup Header Table Edit screen appears. Edit a text according to the procedures described in Appendix “Text Editing”. 10-105 UNI-5 User’s Manual...
  • Page 232 Press the [ESC] key on the key sheet to escape from text editing mode. The confirmation screen appears. Then, press the [SAVE] button. The edited text has been registered. Then, press the Return button. The Lookup Table screen appears Repeat steps 22 through 28 for more header registrations. 10-106 UNI-5 User’s Manual...

  • Page 233: Changing Exisiting Tables

    Press the "Lookup Table” field on the Program Menu Select screen. The Lookup Table screen appears. Select a desired header table by pressing the corresponding field. EXAMPLE Table number “2”. or press the [PLU] key on the key sheet after a numeric entry. 10-107 UNI-5 User’s Manual...
  • Page 234 Press the [DETAIL] button. The Lookup Table Data List screen appears. When changing the header name, press the [EDIT] button The Lookup Header Table Edit screen appears. Edit a text according to the procedures described in Appendix “Text Editing”. 10-108 UNI-5 User’s Manual...
  • Page 235 The confirmation screen appears. Then, press the [SAVE] button. The edited text has been registered. When changing the data text, select a desired data text by pressing the corresponding field. and press the [DETAIL] button. The Lookup Data Table Edit screen appears. 10-109 UNI-5 User’s Manual...
  • Page 236 The confirmation screen appears. Then, press the [SAVE] button. The edited text has been registered. Repeat steps 10 through 14 for more data text registrations. Repeat steps 3 through 15 for more header table text registrations. 10-110 UNI-5 User’s Manual...
  • Page 237 Press the "Mince Traceability” field on the Program Menu Select screen. The Mince Traceability screen appears. Enter a numeric value and press the corresponding field for registration. Then, press the Return button to finalize this procedure. 10-111 UNI-5 User’s Manual...
  • Page 238 The Fix Price Mark List screen appears. Enter a desired mark number using the numeric keys and press the [PLU] key on the key sheet. EXAMPLE Mark number “6”. The confirmation screen appears. Then, press the [ENTER] button. 10-112 UNI-5 User’s Manual...
  • Page 239 Press the [ESC] key on the key sheet to escape from text editing mode. The confirmation screen appears. Then, press the [SAVE] button. The edited text has been registered. To finalize this procedure, press the Return button. 10-113 UNI-5 User’s Manual...

  • Page 240: Changing Exisiting Price Marks

    Press the "Fixed Mark” field on the Program Menu Select screen. Select a desired mark number by pressing the corresponding field. EXAMPLE Mark number “2”. or press the [PLU] key on the key sheet after a numeric entry. The Fix Price Mark Edit screen appears. 10-114 UNI-5 User’s Manual...
  • Page 241 Press the [ESC] key on the key sheet to escape from text editing mode. The confirmation screen appears. Then, press the [SAVE] button. The edited text has been registered. Repeat steps 2 through 6 for more registrations. 10-115 UNI-5 User’s Manual...
  • Page 242 Press the "Free” field on the Program Menu Select screen. The Free Message List screen appears. Then, press the [NEW] button. The confirmation screen appears. Then, press the [ENTER] button. The Free Message Edit screen appears. 10-116 UNI-5 User’s Manual...
  • Page 243 The confirmation screen appears. Then, press the [SAVE] button. The edited text has been registered. Enter a desired message number using the numeric keys and press the [PLU] key on the key sheet. EXAMPLE Message number “2”. 10-117 UNI-5 User’s Manual...
  • Page 244 Enter a desired message number using the numeric keys and press the [PLU] key on the key sheet. EXAMPLE Message number “2”. The confirmation screen appears. Then, press the [ENTER] button. Repeat steps 4 through 8 for more registrations. 10-118 UNI-5 User’s Manual...
  • Page 245 Press the "Fixed Mark” field on the Program Menu Select screen. The Free Message List screen appears. Select a desired message number by pressing the corresponding field. EXAMPLE Message number “2”. or press the [PLU] key on the key sheet after a numeric entry. 10-119 UNI-5 User’s Manual...
  • Page 246 Press the [ESC] key on the key sheet to escape from text editing mode. The confirmation screen appears. Then, press the [SAVE] button. The edited text has been registered. Repeat steps 3 through 7 for more registrations. 10-120 UNI-5 User’s Manual...
  • Page 247 CHECK LABEL REGISTRATION Press the "Check Label” field on the Program Menu Select screen. The Check Label screen appears. Enter Start Number and End Number using the numeric keys and press the corresponding fields for registration. 10-121 UNI-5 User’s Manual...
  • Page 248 Chapter 10 PROGRAM MODE Press the [STRAT] button to print the labels. 10-122 UNI-5 User’s Manual...

  • Page 249: Setup Mode

    Press the [MODE] key on the key sheet. The Operation Mode screen appears. Then, press the [SETUP] button on the screen The Setup Menu Select screen appears. To change the pages, press the [ ] or [ ] button on the screen. UNI-5 User’s Manual 11-1...
  • Page 250 Chapter 11 SETUP MODE 11-2 UNI-5 User’s Manual...
  • Page 251 Press the “MACHINE No.” field on the Setup Menu Select screen. The Machine Number (Basis) screen appears. Enter a desired numeric value and press the “Dept No.” field. EXAMPLE Dept number “9” The confirmation screen appears. Then, press the [EXEC] button to continue. UNI-5 User’s Manual 11-3...
  • Page 252 Chapter 11 SETUP MODE 11.3 SALES MODE SETTING Press the “Sales Mode” field on the Setup Menu Select screen. The Sales Mode screen appears. Select a desired mode by pressing the correponding button. EXAMPLE “Self-service Mode” 11-4 UNI-5 User’s Manual...
  • Page 253 To change the pages, press the [ ] or [ ] button on the screen. Press the [TOTAL] tab to display the Password (Total) screen. To change the pages, press the [ ] or [ ] button on the screen. UNI-5 User’s Manual 11-5...
  • Page 254 Chapter 11 SETUP MODE Press the [PROGRAM] tab to display the Password (Program) screen. To change the pages, press the [ ] or [ ] button on the screen. 11-6 UNI-5 User’s Manual...
  • Page 255 Chapter 11 SETUP MODE UNI-5 User’s Manual 11-7...
  • Page 256 To change the pages, press the [ ] or [ ] button on the screen. Press the [ADJUST] tab to display the Password (Adjust) screen. Enter a 6-digit password using the numeric keys and press the [PASSWORD] display field on the screen. EXAMPLE Password “999999” 11-8 UNI-5 User’s Manual...
  • Page 257 Chapter 11 SETUP MODE Press desired buttons to set whether or not to use the password. EXAMPLE Set to apply the password to “Virtual Receipt” in Total Mode. UNI-5 User’s Manual 11-9...
  • Page 258 Press the “Key Lock” field on the Setup Menu Select screen. The Key Lock (Display Key) screen appears. Press the [FUNCTION KEY] tab to display the Key Lock (Function Key) screen. Press the [ ] or [ ] button to change the pages. 11-10 UNI-5 User’s Manual...
  • Page 259 Chapter 11 SETUP MODE UNI-5 User’s Manual 11-11...
  • Page 260 Chapter 11 SETUP MODE 11-12 UNI-5 User’s Manual...
  • Page 261 Press a desired mode by pressing the corresponding tab, and press to select desired buttons to set whether or not to use the password. EXAMPLE Set to apply the password to “Multi” in Function Key Mode. UNI-5 User’s Manual 11-13...
  • Page 262 The Data Staorage (Total Add) screen appears. Press the [ ] or [ ] button to change the pages. Press desired buttons to set whether or not to use the total addition. EXAMPLE Set to use the operator total addition. 11-14 UNI-5 User’s Manual...
  • Page 263 Chapter 11 SETUP MODE 11.7 PRESET REPORT SETTING Press the “Preset Report” field on the Setup Menu Select screen. The Preset Report (Daily) screen appears. Press the [ ] or [ ] button to change the pages. UNI-5 User’s Manual 11-15...
  • Page 264 Chapter 11 SETUP MODE Press the [WEEKLY] tab to display the Preset Report (Weekly) screen. 11-16 UNI-5 User’s Manual...
  • Page 265 Chapter 11 SETUP MODE Press the [CUMULATIVE] tab to display the Preset Report (Cumulative) screen.. Press the [ ] or [ ] button to change the pages. UNI-5 User’s Manual 11-17...
  • Page 266 Chapter 11 SETUP MODE Press a desired mode by pressing the corresponding tab, and press to select desired buttons to set whether or not to print the totals EXAMPLE Set to print the Production Daily Total (Total). 11-18 UNI-5 User’s Manual...
  • Page 267 Press the “Auto Program” field on the Setup Menu Select screen. The Item Auto Overwrite screen appears. Press the [ ] or [ ] button to change the pages. Note: Display items may vary depending on the country setting. UNI-5 User’s Manual 11-19...
  • Page 268 Chapter 11 SETUP MODE Press to select desired buttons to set whether or not to overwrite the items automatically. 11-20 UNI-5 User’s Manual...
  • Page 269 Press the [<] or [>] button to select a desired Markdown Mode. 1: Special price 2: Amount discount for total price MARKDOWN 3: Percent discount for total price MODE 4: Special unit price 5: Amount discount for unit price 6: Percent discount for unit price UNI-5 User’s Manual 11-21...
  • Page 270 Enter a fixed weight and press this field. TARE Enter a tare weight and press this field. UNDER WEIGHT Enter a lower weight limit and press this field. UPPER WEIGHT Enter an upper weight limit and press this field. 11-22 UNI-5 User’s Manual...
  • Page 271 1: Fixed weight POINTS Enter a point data and press this field. Press the “MESSAGE” tab to display the Item Initial Data (Message) screen. Press a desired field to display the corresponding list screen. EXAMPLE “Extra Message 1” UNI-5 User’s Manual 11-23...
  • Page 272 Chapter 11 SETUP MODE Select a desired message by pressing the corresponding field. The selected message has been registered. Press the “IMAGE” tab to display the Item Initial Data (Image) screen. Press to select a desired image field. 11-24 UNI-5 User’s Manual...
  • Page 273 The Image List screen appears. Then, select a desired image by pressing the corresponding field. The selected image has been registered. Press the Display Image field. The Display Image List screen appears. Then, select a desired image by pressing the corresponding field. UNI-5 User’s Manual 11-25...
  • Page 274 Press the [<] or [>] button to select whether or not to print first labels. FIRST LABEL 1: Yes PRINT 2: No Press the [<] or [>] button to select whether or not to print first labels. SECOND 1: Yes LABEL PRINT 2: No 11-26 UNI-5 User’s Manual...
  • Page 275 Enter a POS flag number and press this field. BARCODE Enter a barcode and press this field. Press the [<] or [>] button to select a desired reference method. 0: Refer POS REFERENCE 1: PLU file UNI-5 User’s Manual 11-27...
  • Page 276 Press to select a desired format. POS FORMAT TRACE ENABLE Press to select whether or not to enable traceability function. DEPARTMENT NO. Enter a department number and press this field. GROUP NO. Enter a group number and press this field. 11-28 UNI-5 User’s Manual...
  • Page 277 Press the “PLU Update” field on the Setup Menu Select screen. The PLU Update screen appears. Press the [ ] or [ ] button to change the pages. Note: Display items may vary depending on the country setting. UNI-5 User’s Manual 11-29...
  • Page 278 Chapter 11 SETUP MODE 11-30 UNI-5 User’s Manual...
  • Page 279 Chapter 11 SETUP MODE UNI-5 User’s Manual 11-31...
  • Page 280 Chapter 11 SETUP MODE Enter the start and end numbers and press these fileds to specify the target PLUs. Select desired items by pressing the corresponding fields. 11-32 UNI-5 User’s Manual...
  • Page 281 Chapter 11 SETUP MODE To release the selection, press the selected field again. To release all the selections, press the [BATCH DELETE] button. UNI-5 User’s Manual 11-33...
  • Page 282 Chapter 11 SETUP MODE Press the [EXECUTE] button to update the selected items. Press the [EXEC] button for execution. 11-34 UNI-5 User’s Manual...
  • Page 283 Press the “PLU Update” field on the Setup Menu Select screen. The Receipt Setting screen appears. To edit the header and footer titles, press the corresponding field. The Receipt Title Edit screen appears. Edit the text according to the procedure explained in Appendix “Text Editing”. UNI-5 User’s Manual 11-35...
  • Page 284 The edited text has been registered. To edit the header and footer logo images, press the corresponding field. The Image List screen appears. Select a desired image by pressing the corresponding filed, and press the [SET] button. 11-36 UNI-5 User’s Manual...
  • Page 285 Chapter 11 SETUP MODE The edited logo image has been registered. UNI-5 User’s Manual 11-37...

  • Page 286: Text Editing

    Used to specify a normal left. Also used to select character style. characters for changing the style. Used to select either lower-case or upper-case Used to specify a bold character mode for a text to character style. be entered. UNI-5 User’s Manual...
  • Page 287 Used to specify a revered Used to begin a new character character. line. Used to select either a Used to enter a space at the lower-case or upper-case place where the cursor is mode for a character to be positioned. entered. UNI-5 User’s Manual...
  • Page 288 Select a desired character size by using the [Size] key on the key sheet. The selected size is displayed in the “FONT” display field. Press the [Lower Case] key on the key sheet to select whether to use upper-case characters or lower-case characters. UNI-5 User’s Manual...
  • Page 289 Appendix TEXT EDITING Enter desired characters using alpha-numeric keys on the key sheet or the screen. Upper-case characters Lower-case characters UNI-5 User’s Manual...
  • Page 290 To change to a new line, press the [New Line] key on the key sheet. Enter desired characters. To finalize the editing, press the [ESC] key on the key sheet. The confirmation screen appears. Then, press the [SAVE] button to save the data. UNI-5 User’s Manual...
  • Page 291 To select a desired character style using the following keys. The selected style is displayed in the “STYLE” display field. EXAMPLE Select reversed characters. Enter desired characters using alpha-numeric keys on the key sheet or the screen. UNI-5 User’s Manual...
  • Page 292 Appendix TEXT EDITING Press the [ESC] key on the key sheet. The confirmation screen appears. Then, press the [SAVE] button to save the data. UNI-5 User’s Manual...
  • Page 293 Confirm that the text edit screen for a desired PLU is displayed. To delete the character line, press the [Line Delete] key on the key sheet. Press the [ESC] key on the key sheet. The confirmation screen appears. Then, press the [SAVE] button to save the data. UNI-5 User’s Manual...
  • Page 294 To Make a correction for a misspelled word, move the cursor to a place where misspelling is made by using the [→] or [←] key. “GAUDA” → “GOUDA” EXAMPLE Press the [Character Delete] key on the key sheet to delete the misspelled character. UNI-5 User’s Manual...
  • Page 295 Appendix TEXT EDITING Enter the correct character using the alpha-numeric keys. Press the [ESC] key on the key sheet. The confirmation screen appears. Then, press the [SAVE] button to save the data. A-10 UNI-5 User’s Manual...
  • Page 296 CHARACTER BACKSPACING To delete a wrong character that was just entered, press the [Back Space] key on the key sheet to move the cursor back by one character. “E” → “A” EXAMPLE Enter a correct character. UNI-5 User’s Manual A-11...
  • Page 297 Appendix TEXT EDITING Complete the text. Press the [ESC] key on the key sheet. The confirmation screen appears. Then, press the [SAVE] button to save the data. A-12 UNI-5 User’s Manual...
  • Page 298 Design and specifications are subject to change without notice. 44 SANNO-CHO, SHOGOIN, SAKYO-KU KYOTO, 606-8392 JAPAN PHONE: 81-75-771-4141 FACSIMILE: 81-75-751-1634 URL: http://www.ishidajapan.com...

Table of Contents