DAELIM B-Bone Service Manual page 109

PILOT SCREW
PILOT SCREW PILOT SCREW PILOT SCREW PILOT SCREW PILOT SCREW PILOT SCREW
PILOT SCREW PILOT SCREW PILOT SCREW PILOT SCREW PILOT SCREW PILOT SCREW
PILOT SCREW PILOT SCREW PILOT SCREW PILOT SCREW
PILOT SCREW PILOT SCREW PILOT SCREW PILOT SCREW PILOT SCREW
MUFFLER MUFFLER MUFFLER MUFFLER MUFFLER MUFFLER MUFFLER
MUFFLER MUFFLER MUFFLER MUFFLER MUFFLER MUFFLER
MUFFLER MUFFLER MUFFLER MUFFLER
MUFFLER MUFFLER MUFFLER MUFFLER MUFFLER
THROTTLE STOP SCREW THROTTLE STOP SCREW THROTTLE STOP SCREW THROTTLE STOP SCREW THROTTLE STOP SCREW
THROTTLE STOP SCREW THROTTLE STOP SCREW THROTTLE STOP SCREW THROTTLE STOP SCREW
THROTTLE STOP SCREW THROTTLE STOP SCREW THROTTLE STOP SCREW THROTTLE STOP SCREW THROTTLE STOP SCREW THROTTLE STOP SCREW
THROTTLE STOP SCREW THROTTLE STOP SCREW THROTTLE STOP SCREW THROTTLE STOP SCREW THROTTLE STOP SCREW THROTTLE STOP SCREW THROTTLE STOP SCREW
O-RING O-RING O-RING O-RING O-RING
O-RING O-RING O-RING O-RING
O-RING O-RING O-RING O-RING O-RING O-RING
O-RING O-RING O-RING O-RING O-RING O-RING O-RING
THROTTLE STOP SCREW
THROTTLE STOP SCREW THROTTLE STOP SCREW THROTTLE STOP SCREW THROTTLE STOP SCREW THROTTLE STOP SCREW THROTTLE STOP SCREW
THROTTLE STOP SCREW THROTTLE STOP SCREW THROTTLE STOP SCREW THROTTLE STOP SCREW THROTTLE STOP SCREW THROTTLE STOP SCREW
THROTTLE STOP SCREW THROTTLE STOP SCREW THROTTLE STOP SCREW THROTTLE STOP SCREW
THROTTLE STOP SCREW THROTTLE STOP SCREW THROTTLE STOP SCREW THROTTLE STOP SCREW THROTTLE STOP SCREW
EMISSION ANALYZER EMISSION ANALYZER EMISSION ANALYZER EMISSION ANALYZER EMISSION ANALYZER EMISSION ANALYZER EMISSION ANALYZER
EMISSION ANALYZER EMISSION ANALYZER EMISSION ANALYZER EMISSION ANALYZER EMISSION ANALYZER EMISSION ANALYZER
EMISSION ANALYZER EMISSION ANALYZER EMISSION ANALYZER EMISSION ANALYZER
EMISSION ANALYZER EMISSION ANALYZER EMISSION ANALYZER EMISSION ANALYZER EMISSION ANALYZER
INSPECTION
● Check the carburetor insulator O-ring for wear or
damage.
● Install in the reverse order of removal.
PILOT SCREW ADJUSTMENT
USING THE EMISSION ANALYZER (CO,HC)
● Open the seat and remove the center cover.
Turn the pilot screw clockwise until it seats lightly,
then back it out to the specification given(1 ).
Warm up the engine to operating temperature (60 ).
Adjust the idle speed with the throttle stop screw.
IDLE SPEED : 1,700
NOTE
!
Before adjustment the pilot screw, check the
following items.
- Fuel system electrical system for troubling.
- Do not force the pilot screw against its seat ;
The seat will be damaged.
- Spark plug for cleaning and gap adjusting.
- Valve clearance for adjusting.
- Emission analyzer for correction.
Exhaust gas contains poisonous substance.
Do not adjusting for a long period of time in a
closed, or poorly ventilated area.
Extend the hose (60Cm) at the tail pipe, and insert the
probe of the emission analyzer to the tail pipe, and
adjust the pilot screw with a
3~4%.
Adjust by the throttle stop screw, repeat steps
until accord the idle rpm (1,800rpm) and the Co
(3~4%).
FUEL SYSTEM
100RPM
the Co to became
and
6-9