Page 2
This motorcycle is designed to carry the operator and one passenger. WARNING Attempting to change the pre-set maximum speed may cause danger and will void the Daelim warranty. ON-ROAD USE This motorcycle is designed to be used only on the road.
CONTENTS SPECIFICATION PROPER DRIVING METHODS OPERATION INSTRUCTION(SAFETY PRECAUTIONS) DRIVING IN A SLOPING ROAD SELF INSPECTIONS BEFORE OPERATION PRIOR TO STARTING VEHICLE / OPERATION INSPECTION OF SUSPICIOUS AREA OF THE VEHICLE WHEN DRIVING CORRECT ATTIRE IN THE PREVIOUS DAY CARGO/MODIFICATION/ATTACHMENT/MUFFLER BRAKE INSPECTION PARTS LOCATION TIRE INSPECTION METER READING AND USAGE...
Page 4
CABLE RUBBER PART TURNING METHOD SIDE STAND INSPECTION PRINCIPLE OF TURN CLEANING EFFECT OF SPEED INSPECTION SHEET 3 POSITIONS OF TURNING DAILY INSPECTION(BEFORE DRIVING) TURNING METHOD REGULAR INSPECTION BRAKING METHOD ABOUT REGULAR INSPECTION BASIC PRINCIPLE OF BRAKE(FRICTION FORCE) DAILY INSPECTION, REGULAR INSPECTION RESTRAINT OF BRAKING EFFECT (INERTIA) RECOMMENDED REPLACEMENT PARTS BRAKING METHOD...
OPERATION INSTRUCTION SAFETY PRECAUTIONS This manual describes matters pertaining to correct operation, ●Careful driving and the wearing of proper attire and safety safe operation and simple maintenance of the vehicle you equipment are the most important factors in the safe operation purchased.
PRIOR TO STARTING VEHICLE OPERATION ●Read user's manual carefully. ●Operators should naturally fix bodies to keep smooth driving. ●Conduct maintenance checks prior to operation. ●Please check whether or not you are unnaturally strained and ●Always maintain vehicle in clean status and carry out specified strung up.
CORRECT ATTIRE ●Always make sure to wear helmet for safety. Wear gloves and A helmet should always be worn and the helmet chin safety goggles. strap should be securely ●Do not wear uniforms which might hinder operation. It is fastened. dangerous if the uniform is caught by brake lever or by the Correct shirts or jackets with rotating part of drive chain.
Modifications are not covered by warranty. ATTACHMENT ●Except designated attachment by DAELIM MOTOR CO., LTD., don't attach any extra lighting device, because it may cause an early discharging of battery.
PARTS LOCATION REAR CARRIER BACK REST REAR BRAKE LEVER MAIN SWITCH FRONT BRAKE LEVER BATTERY SEAT FUSE OPEN SWITCH COOLING WATER RESERVE TANK MUFFLER ANTENNA TIRE OIL LEVEL GAUGE WATER PUMP BACK HOLD PILLION STEP...
Page 11
PARTS LOCATION REAR CARRIER BACK REST REAR BRAKE LEVER FRONT SEAT RECEIVER(SMART KEY) FUEL TANK LID TAIL LIGHT HEAD LIGHT FRONT FENDER FRONT CUSHION AIR CLEANER BRAKE DISK SIDE STAND BRAKE CALIPER MAIN STAND...
METER READING AND USAGE METER NOTE During riding, please drive the THERMOMETER TACHOMETER ● SPEEDOMETER scooter in order that the RPM of ENGINE CHECK LAMP engine shall NOT be positioned in the dangerous area(red area) of WINKER TRIP tachometer. INDICATOR ODO(METER) <Thermometer>...
METER READING AND USAGE SWITCH OPERATING OFF) ③ INDICATING LAMPS MAIN SWITCH The position of Engine stop. <Winker indicators / Emergency lamp> ● The lever of main switch shall be , lift up the STEERING LOCK) ④ emergency lamp switch, the emergency lamp lights. Push the lever, turn to the left, the steering will be locked(In order to release steering lock, push the <Engine Check lamp(indicates repair and...
SWITCH OPERATION START BUTTON WARNING CAUTION Be the main switch lever (ON), grip Do not use the engine stop switch The usage of upward light shall be only ● ● the brake and push the starter button, the except the emergency or stop. used on condition that it does not interrupt During riding, if operate the engine engine operates(the green lamp lights).
PASSING SWITCH WINKER SWITCH EMERGENCY SWITCH Emergency Switch If the main switch lever is (ON), push it 2 or 3 times. This switch is used when passing the other vehicle. Passing Switch Winker Switch Regardless of main lever switch position, the emergency switch can be operated.
EQUIPMENT USAGE AT STARTING Smart key LED CAUTION The rider gets the Smart key and gets on the Surely check whether the engine stop switch Smart key ● is ON before starting or it has out of order. If vehicle(within 1 meter), turn the main switch the engine stop switch is OFF, starting the lever to the position (ON), push the button...
STEERING STEM LOCK REAR CUSHION CAUTION Move lightly the steering stem to the ● left and the right to check whether it is locked completely to the “ LOCK “ position. Park the vehicle at the safe place not to ●...
OPERATION SEAT LOCK TRUNK CAUTION <LOCK> TRUNK Push and close the seat, it automatically locked. ● Do not load the excessive cargo in ● Check the seat locked by lifting it slightly. the trunk. If the seat being locked by ●...
SEAT BACK REST INNER BOX LID CHARGE SOCKET Depending upon the rider’s convenience, you can When open or close the inner box lid, use the normal At starting the engine, open the inner box lid and put adjust the position of SEAT BACK REST. key.
CORRECT DRIVING OPERATION ENGINE STARTING <USING THE ELECTRIC START(CELL)> Lock the rear wheel Make sure to check the oil, gasoline, etc., before ● Press the start button without rotating the throttle grip. ● starting the engine. ※ At searching the Smart key, the time of certification Please ensure that the main stand and side stand are ●...
On condition that the engine is heated, only pressing ● WARNING CAUTION the starter button gets the vehicle started. When getting on and starting the At seriously cold season, the battery ● ● To prevent the battery discharge, do not rotate over vehicle, grip the brake lever and ●...
Page 22
Get on the vehicle. Start the engine(refer to the engine starting method). Release the squeezing tension on the rear brake lever and slowly begin to rotate the throttle grip to Mounting should be done from the left side, and ● allow for a slow and easy start.
Speed is controlled by the operation of the Work the front and rear brakes together. PROPER DRIVING METHODS throttle grip.. Allow the throttle grip to rotate back to its beginning ● If the throttle grip is rotated…. Before entering traffic, use the correct turn signal to position and then squeeze the brake levers.
Page 24
Special care in driving should be taken during STOPPING WARNING rainy weather. If using the only one brake, the vehicle ● When approaching the desired stopping area. More braking distance is needed when driving on ● may being slip aside that causes the death Activate the proper winker, and after checking for wet roads or in the rain.
Page 25
After the vehicle has come to a complete stop. Dismount on the left side and lower the main stand To prevent theft, be sure to lock the steering when Return the winker switch to the center position and on a flat surface. parking, and do not keep the Smart key in the ●...
DRIVING IN A SLOPING ROAD CAUTION If driving over the maximum sloping ● The driving in a sloping road needs the engine high ● road or loading heavy baggage, it may RPM, then on the steep place, frequent driving may cause the engine being early heated or cause the engine hard worked and early heated, then the rider to have difficulty to drive,...
SELF INSPECTIONS BEFORE OPERATION Inspect by yourself the vehicle and have regular INSPECTION OF SUSPICIOUS CAUTION maintenance inspections for increased safety and the AREA OF THE VEHICLE WHEN Specified brake lever free play must DRIVING IN THE PREVIOUS DAY ● prevention of accidents.
CRACK/DAMAGE TIRE INSPECTION CAUTION Check tire tread and side of crack and damage. If the brake fluid reduces prominently ● AIR PRESSURE CHECKING below the lower limit, the braking Check for an appropriate level of air pressure by power may get lower that this occurs accidents.
FOREIGN MATERIALS FUEL CHECK CAUTION Check tire tread and sides for nails, rocks, etc. That If air pressure is inadequate or if there ● CHECK might have become wedged in the tire. are cracks, damage or abnormal wear Check gasoline to see if there is a sufficient amount of on tires, it may cause trembling FOREIGN steering wheel and flat tire.
REFUELING ENGINE OIL LEVEL CHECK CAUTION Press the main switch lever and after certificating the ● Gasoline is extremely flammable and Stand the scooter by its main stand on level ground ● ● Smart key, turn the lever to the left, then the fuel tank is explosive under certain conditions.
operating sound of winker works or not REPLACEMENT OF HEAD LIGHT LIGHT / WINKER INSPECTION BULBS In addition, check whether lens are dirty or damaged HEADLIGHT, TAIL LIGHT Loosen 4 socket bolts and remove the windscreen. ① (cracked) or not. Start the engine and operate switches whether the lights Untie 7 tapping screws and remove the front cover.
Page 32
<THE ILLUMINATION ANGLE OF ④ Pull the headlight socket and remove it. HEAD LIGHT> ⑤ Remove the rear cover. By adjusting the adjuster bolt of headlight, adjust its ● ⑥ Untie steel wire and remove the head light. illumination angle. ⑦...
Page 33
[ REPLACEMENT OF WINKER BULB ] REAR WINKER BULB 12V 10W INSPECTION OF COOLING WATER FRONT WINKER BULB > WINKER LENS ① Stand the vehicle onto the flat ground by main Dip into a hand under the front cover. ① stand.
REPLENISHING FRONT, REAR SIMPLE MAINTENANCE BRAKE FLUID This section is an explanation of correct inspection PIECE Clean dust and other foreign materials around ① methods about the result of vehicle inspection, cleaning, reserve tank to prevent foreign materials from adjustment, replacement, etc. Please always refer to this falling inside tank.
FRONT BRAKE BRAKE HOSE, PIPE LEAKAGE, DAMAGE, ASSEMBLY STATE CAUTION CUT OUTS Visually check for fluid leakage or damage and, using When replenishing the brake fluid, be careful that ● dirt or water, etc attached to reserve tank is not a spanner, check joints and clamps for clearance.
CHANGING ENGINE OIL CAUTION When changing the engine oil immediately after SPECIFIED GENUINE OIL ● When the engine oil is contaminated, the life of engine stopping the engine, be careful not to be burnt the Don’t fill the low grade oil. Using it can cause damage will be remarkably shortened.
FRONT, REAR BRAKE PAD CAPACITY OF TRANSMISSION OIL OIL LEAK RECOMMENDED OIL Stand the main stand on a flat place, 2~3 minutes Check to see if transmission oil leaks out from ● RECOMMENDED OIL : SAE80W-90 later after stopping the engine, disassemble bolts, transmission case or check bolt.
SPARK PLUG COOLING WATER REPLACEMENT RESERVE If electrode is stained or its clearance is not right, Open the right side inner cover lid. ① TANK CAP satisfactory spark is not made. Clean and make ② Disassemble the Reserve Tank Cap. Untie the drain bolt of water pump and discharge INLET ③...
STANDARD PLUG : CR8EH-9 CLEANING TERMINALS OF BATTERY If new plug is installed, turn 3/4 and tighten it by using ● When removing the pillion seat and open the battery CAUTION a plug wrench ● If plug is reused, turn 1/8 and tighten it. cover, you can find the battery.
● so check or refilling of electrolyte will holder. Then, remove the disconnected not be required. If there is any abnormal, contact to Daelim service fuse, and insert the reserved fuse with center. same capacity. If you reform the battery for car, battery ●...
■ CUT AIR CLEANER ELEMENT INSPECTION ■ NORMAL CAUTION <REMOVAL> If the air cleaner element is Loosen the 6 screws assembling the air ① ● inadequately assembled, dust and cleaner case cover and remove the tube other waste materials can directly clip and air cleaner case cover.
CVT DUST COVER ELEMENT CABLE RUBBER PART INSPECTION LOCK NUT INSPECTION, CLEANING A rubber boots is assembled on the cable <DISASSEMBLY> to protect the inner cable. Untie 2 bolts in LH. Crank Case Cover ① Make sure that this part is placed firmly and disassemble CVT DUST COVER around the correct part of the cable.
SIDE STAND INSPECTION CLEANING Make sure to stop the engine prior to ● Erect main stand and place vehicle in At washing, be careful for water not to ● ● vehicle. upright position on level ground. flow into the trunk(luggage box). At Be careful not to allow water to enter ●...
INSPECTION SEET • In order for safe scooter driving, always maintain healthy condition of the vehicle. This inspection sheet includes how to check and maintain the vehicle, says about its heath care and maintenance. Be sure to read fully and keep in mind the inspection contents. Also, please care for the inspection result that shall be written.
DAILY INSPECTION(BEFORE DRIVING) CAUTION For safe and comfortable usage of the vehicle, the daily inspection In case that the vehicle is used at other conditions(for means that you, customer check and inspect your vehicle directly and ● instance, like seriously commercial used like for delivery, basically once daily.
② ● ABOUT THE REGULAR INSPECTION Principal oils ① Engine oil The regular inspection and maintenance Brake fluid ② are in charge of customer. Transmission oil ③ The regular inspection and maintenance is for the healthy care of the vehicle ! In order for safe driving, the daily and regular inspection and ①...
DAILY INSPECTION, REGULAR INSPECTION POINT 3 – Abrasive parts At using the vehicle, shall do obligatorily one day once inspection(before driving) and regular inspection for the purpose There are many abrasive parts in the of safe and comfortable driving. vehicle. WARNING There are parts doing their roles by being worn like the eraser.
Page 50
REMARKS In case of * points, please perform at proper ) ※ DAILY INSPECTION time(long driving, washing, fueling) by checking Inspected parts or Inspection details contents the vehicle driving distance, vehicle driving Do brake pedal and lever operate well, also •...
RECOMMENDED REPLACEMENT PARTS Depending upon the vehicle driving distance and time going by, The repair and maintenance of regularly replaced parts is done even though there is not outer shape disorder , there are a few by yourself and paid by yours. parts that are difficult to decide whether they can be used longer or not.
For the vehicle performance fully done, it is important to select Frequent driving on off-road. • the proper oil and be used. Please use the designated genuine oil Repeating of short distance driving • to DAELIM vehicles. Frequent usage at idling • Using at cold area • •...
INSPECTION AND MAINTENANCE INSPECTION AND MAINTENANCE WARNING If you do not observe the proper inspection and repair ● Be careful about enough safety at inspection method, this may occur accident like turn-over, even • Select the flat and durable ground at inspection, erect the main happen death or serious damage.
DAILY, INSPECTION CHECKLIST ③ The air pressure of tire ④ ① The free-play of brake lever ② The capacity of brake fluid ⑤ The capacity of engine oil Tire crack, unusual abrasion, metal fragment, and other alien material the depth of home. ⑥...
INSPECTION METHOD, TIPS DAILY INSPECTION METHOD There are little difference depending upon the vehicles. Erect the main stand at flat place, move the steering handle and position the As for the difference, please refer to each vehicle’s user’s manual. upper side of reserve tank cap If you think that your daily inspection has something wrong, horizontally.
Page 56
INSPECTION METHOD, TIPS INSPECTION METHOD, TIPS •Checking of crack or damage ENGINE •Inspection of engine oil capacity(※) Check whether there is prominent crack or damage around the tire. Crack Alien At flat ground, do idling the engine for a Also, check whether nail, stone or alien material few minutes, erect the vehicle and stop material stuck to the surface if tire.
INSPECTION METHOD, TIPS INSPECTION METHOD, TIPS CHECKING ABOUT LOW SPEED AND ACCELERATION(※ ※ ) Check whether the fuel gauge at engine FUEL CAPACITY start is within the “ E “ range(red) or whether the main switch is “ ON “. Check whether there is something wrong at low speed or accelerating.
CHECKING POINTS Checking Checking points Detail checking contents timing Checking Checking points Detail checking contents Engine timing (1) Check whether the engine operates 1. Engine starting, promptly and works well. abnormal noise (1) Separate the spark plug, check by Ignition system eye whether there is the 1.
Page 59
Checking Checking Checking points Detail checking contents Checking points Detail checking contents timing timing 5. The abrasion, damage of 3. The status of emission (1) On condition that the engine gets (1) Check whether the drive belt is 6 Mon. 6 Mon.
Page 60
Checking Checking points Checking Detail checking contents Checking points Detail checking contents timing timing Lubrication Equipment 2. Checking the quantity of 1. Engine oil / engine oil, transmission (1) Check by eye whether there is oil (1) On the condition that the main 6 Mon.
Page 61
Checking Checking Checking points Checking points Detail checking contents Detail checking contents timing timing FUEL SYSTEM Cooling system (FUEL LINE) 1. Checking the quantity of (1) Check whether the quantity of (1) Check by eye the connection points 6 Mon. 6 Mon.
Page 62
Checking Checking Checking points Checking points Detail checking contents Detail checking contents timing timing CVT DUST COVER EXHAUST PIPE and (1) Check by eye whether there is 6 Mon. ELEMENT MUFFLER contamination or clog, etc by (4,000km) 1. Contaminated, clogged 1.
Page 63
Checking Checking Checking points Checking points Detail checking contents Detail checking contents timing timing FRONT FORK BRAKE LEVER 1. Damage (1) Pull enough the brake lever by 1. Free play 6 Mon. (1) Check by eye whether there is 12Mon. hand and check whether the free (4,000km) damage in front fork.
Page 64
Checking Checking Checking points Checking points Detail checking contents Detail checking contents timing timing RESERVE TANK BRAKE HOSE and 1. The quantity of brake PIPE (1) Check by eye whether the fluid 6 Mon. fluid 1. Leakage, Damage, quantity of reserve tank is within (1) Operate the brake strongly, check (4,000km) 6 Mon.
Page 65
Checking Checking Checking points Checking points Detail checking contents Detail checking contents timing timing WHEEL (1) Check whether air pressure is BRAKE DISK and 6 Mon. within the designated limit by 1. Tire condition (4,000km) PADS using tire gauge. 1. Gap between disk and (1) Operate brake a few times and 12Mon.
Page 66
Checking Checking Checking points Checking points Detail checking contents Detail checking contents timing timing (1) Check whether assembly of nut (1) Check by hands whether the 2. Wheel bolt, nut 6 Mon. 12Mon. SWING ARM assembled between axle shaft and assembled points like swing arm, (4,000km) (8,000km)
Page 67
Checking Checking Checking points Checking points Detail checking contents Detail checking contents timing timing BATTERY SWITCHES 1. Connecting status of (1) Check by eye whether there is any 6 Mon. 1. Operating of lights, terminals (1) Check by eye whether there is signals 6 Mon.
Page 68
Checking Checking Checking points Checking points Detail checking contents Detail checking contents timing timing FRAME 3. Meter (1) Check whether the gauge of 1. Frame 12Mon. (1) Check whether the bolts, nuts of 12Mon. speedometer operates without (8,000km) frame are loose or not with the (8,000km) matter or not.
Page 69
Checking Checking points Detail checking contents timing 2. Rubber bush of cables (1) Check by eye whether the rubber 6 Mon. bushes are correctly assembled or (4,000km) not. MARK MARK...
SAFE DRIVING PREPARATION BEFORE DRIVING ● Performing daily inspection ● Putting on the protective gears (Helmet, glove, goggles, etc.) ● Bringing the driver's licence ● Determinating the path to the desired destination...
DRIVING POSITION The appropriate driving position is most important thing to driving safely. ① Eyes : Look at the front direction widely. ② Shoulders : Relieve the tension. ③ Arms : Relieve the tension and bend arms to inside and let ①...
TAKING POSE OF FELLOW PASSENGER ① Hands: Hold the rear grip. WARNING ② Feet and knees: Put the feet on pillion step, and adhere the the fellow passenger doesn’t hold the rear grip or put the ● knees closely to body. step on the pillion step, it may lead death or serious injury due to falling from the vehicle as sudden start, stop or turning.
PRECAUTION WHEN DRIVING ● Secure the safe distance. ● If any abnormality is found, stop driving and contact service ● Drive protectively. center to inspect the vehicle. ● Do not obstruct the traffic. ● Restart the vehicle after 2~3 min when it is turned over. ●...
STARTING Prior to starting always look around to avoid accident. ① Get on the vehicle after pulling back the stand. ② Start driving slowly after turning on the winker and releasing the brake while ensuring the safety around the vehicle. CAUTION Return the side stand to its original position.
TURNING METHOD PRINCIPLE OF TURN EFFECT OF SPEED CENTRIFUGAL FORCE GRAVITY The centrifugal force increases in inverse portion to the radius The basic principle of turn is balancing using the centrifugal of a curve and in portion to the square speed. Decelerate prior force which makes vehicle go outside and the gravity which to entering the curved way to reduce the centrifugal force.
3 POSITIONS OF TURNING The basic principle of turn is balancing using combined force of < LEAN-IN > the centrifugal force and the gravity. This is a turning position with driver leaned inside more than All 3 positions require straightening the head and keeping the motorcycle.
TURNING METHOD < LEAN-OUT > This is a turning position with motorcycle leaned inside more than driver, which is opposite to the lean-in position. With this position, quick turn is well performed and driver can obtain wide front visual field adequate to drive on the rained or slippy road because it has best road holding.
Page 82
PRECAUTION WHEN TURNING Do not drive inside of large truck's turn circle. < DEAD ANGLE ZONE > < DISTANCE BETWEEN THE FRONT AND REAR WHEEL TURN > Dead angle zone is the sight range which cannot be identified by It is distance between path of the front and rear wheel and driver and increases in proportion to the width of the vehicle.
BRAKING METHOD BASIC PRINCIPLE OF BRAKING (FRICTION FORCE) RESTRAINT OF BRAKE EFFECT (INERTIA) ● Vehicle is braked using friction between road surface and tires. ● Braking distance increases 1.5 times on wet road and 3 times on icy road because friction force of road surface is decreased.
BRAKING METHOD IMPACT AT COLLISION Learn the proper braking method to prevent accident. ● Turn the throttle grip to its original position and decelerate using the engine brake. ● Erect the vehicle straight. ● Brake using both front and rear brakes. COMPARISION OF BRAKING DISTANCE ·Vehicle speed : 50 km/h When using both front and...