DAELIM B-Bone Service Manual page 129

LH.CRANK CASE COVER/CONTINUOUSLY VARIABLE TRANSMISSION
DRIVEN PULLEY DRIVEN PULLEY DRIVEN PULLEY
DRIVEN PULLEY DRIVEN PULLEY DRIVEN PULLEY DRIVEN PULLEY
DRIVEN PULLEY DRIVEN PULLEY DRIVEN PULLEY DRIVEN PULLEY DRIVEN PULLEY DRIVEN PULLEY
DRIVEN PULLEY DRIVEN PULLEY DRIVEN PULLEY DRIVEN PULLEY DRIVEN PULLEY DRIVEN PULLEY ‚ fi " ‚ fi " ‚ fi " ‚ fi " ‚ fi " ‚ fi " ‚ fi " ˙ fi ‚ fi ˙ fi ‚ fi ˙ fi ‚ fi ˙ fi ‚ fi ˙ fi ‚ fi ˙ fi ‚ fi ˙ fi ‚ fi
DRIVEN PULLEY DRIVEN PULLEY DRIVEN PULLEY ‚ fi " ‚ fi " ‚ fi " ‚ fi " ‚ fi " ‚ fi " ‚ fi " ‚ fi " ˙ fi ‚ fi ˙ fi ‚ fi ˙ fi ‚ fi ˙ fi ‚ fi ˙ fi ‚ fi ˙ fi ‚ fi ˙ fi ‚ fi ˙ fi ‚ fi
‚ fi " ‚ fi " ‚ fi " ‚ fi " ‚ fi " ‚ fi " ‚ fi " ˙ fi ‚ fi ˙ fi ‚ fi ˙ fi ‚ fi ˙ fi ‚ fi ˙ fi ‚ fi ˙ fi ‚ fi ˙ fi ‚ fi
‚ fi " ‚ fi " ‚ fi " ‚ fi " ‚ fi " ‚ fi " ‚ fi " ‚ fi " ˙ fi ‚ fi ˙ fi ‚ fi ˙ fi ‚ fi ˙ fi ‚ fi ˙ fi ‚ fi ˙ fi ‚ fi ˙ fi ‚ fi ˙ fi ‚ fi
‚ fi " ‚ fi " ‚ fi " ˙ fi ‚ fi ˙ fi ‚ fi ˙ fi ‚ fi
DRIVE BELT
DRIVE BELT DRIVE BELT DRIVE BELT DRIVE BELT DRIVE BELT DRIVE BELT
DRIVE BELT DRIVE BELT DRIVE BELT DRIVE BELT DRIVE BELT DRIVE BELT
DRIVE BELT DRIVE BELT DRIVE BELT DRIVE BELT
DRIVE BELT DRIVE BELT DRIVE BELT DRIVE BELT DRIVE BELT
DRIVE FACE DRIVE FACE DRIVE FACE DRIVE FACE DRIVE FACE
DRIVE FACE DRIVE FACE DRIVE FACE DRIVE FACE
DRIVE FACE DRIVE FACE DRIVE FACE DRIVE FACE DRIVE FACE DRIVE FACE
DRIVE FACE DRIVE FACE DRIVE FACE DRIVE FACE
DRIVE FACE DRIVE FACE DRIVE FACE
DRIVEN PULLEY DRIVEN PULLEY DRIVEN PULLEY DRIVEN PULLEY DRIVEN PULLEY
DRIVEN PULLEY DRIVEN PULLEY DRIVEN PULLEY DRIVEN PULLEY
DRIVEN PULLEY DRIVEN PULLEY DRIVEN PULLEY DRIVEN PULLEY DRIVEN PULLEY DRIVEN PULLEY
DRIVEN PULLEY DRIVEN PULLEY DRIVEN PULLEY DRIVEN PULLEY DRIVEN PULLEY DRIVEN PULLEY
DRIVEN PULLEY
CLUTCH/DRIVEN PULLEY INSTALLATION
● Turning the driven pulley ass'y rightside, extend the
belt assemble groove maximum.
● Install the drive belt into driven pulley sub ass'y, install
the drive shaft.
● Install the drive belt into movable drive face..
● Install the drive face, rear axcel collar drive pulley nut.
● Tighten to the specified torque using drive face holder.
TORQUE VALVE : 7.0~8.0kgf m
TOOL : DRIVE FACE HOLDER
● Install the clutch onter into driven pulley sub ass'y and
flange nut.
● Hold the clutch outer using drive universal holder,
install the flange nut to the specified torque.
TORQUE VALVE : 5.5kgf m
TOOL : UNIVERSAL HOLDER
● Install the LH. crank case cover, and tighten the flange
bolt.
8-13