Table of Contents
Advertisement
To add lights or devices to program memory:
1. Press
. The display shows
7
2. Enter
and the display shows
3
3. Press
to add a light. The panel displays
1
#.
NUMBER THEN PRESS
Press
to add a device. The panel displays
4
DEVICE NUMBER THEN PRESS
4. Enter the desired light or device number (1–40) and
press
. The display shows
#
5. To add another light or device, enter the desired light or
device number and press
6. To exit press
+
.
*
*
To delete lights or devices from program memory:
1. Press
. The display shows
7
2. Enter
and the display shows
3
3. Press
to delete a light. The panel displays
2
LIGHT NUMBER THEN PRESS
Press
to delete a device. The panel displays
5
DEVICE NUMBER THEN PRESS
4. Enter the desired light or device number (1–40) and
press
. The display shows
#
5. To delete another light or device enter the desired light
or device number and press
6. To exit press
+
.
*
*
Testing the System
Note
Before testing, it is recommended that you have covers
on all modules (mounted outside the cabinet) and the
panel cabinet door closed. The testing environment
should match the system working environment.
This section describes how to perform the following test
procedures:
q Basic System Commands.
q Testing Panel Backup Battery(s).
q Testing Hardwired Zone Inputs.
q Testing Wireless Sensors.
q Testing Outputs.
q Testing Optional Lights and Devices (X-10 Modules).
q Testing Phone Communication.
q Testing Central Station Communication.
q Adjusting Touchpad Contrast.
You should test the system after installing, servicing, and
adding or removing devices from the system.
Refer "Troubleshooting" on page 50 if correct test results
are not achieved.
Commercial Burglary and Home Navigator System
.
FEATURES MENU
LEARN LIGHTS AND DEVICES
ENTER A LIGHT
ENTER A
#.
/
nn
.
LIGHT
DEVICE
ADDED
.
#
.
FEATURES MENU
LEARN LIGHTS AND DEVICES
ENTER A
#.
ENTER A
#.
/
nn
.
LIGHT
DEVICE
DELETED
.
#
Basic System Commands
Table 12 describes basic touchpad operating commands.
For complete details on system operation, including user
.
programming, refer to the system User Guide.
Note
Refer to Table A12 on page 71 for default access codes.
Table 12: Basic System Operating Commands
Command
1 + 9
1 + 1 + CODE
1 + 2 + CODE
1 + 3 + CODE
8 + 9 + CODE
1 + 0
7 + 5
.
7 + 7 + CODE + Area Area jump
8 + 8
8 + 1 + CODE
0 + 1 + CODE
8 + 7 + CODE
Testing Panel Backup Battery(s)
The panel can both automatically and manually place a test
load on the panel backup battery(s) and measure the voltage
output.
Note
A newly installed battery may require up to eight hours
under panel power before an accurate charge indication.
To manually test the panel backup battery(s):
1. Press
. The display shows
8
2. Press
again to test the battery(s) and display the result.
8
The display will show the battery voltage as
:
(or similar)
13.8
TEST
V
3. Press
to end the battery test immediately. The system
*
will automatically ends the battery test after 15 minutes.
Testing Hardwire and Wireless Zones/
Sensors
It is recommended that you test all hardwired zones and
sensors after all programming is completed and whenever a
zone/sensor-related problem occurs.
Note
While the zone test is a valuable installation and service
tool, it only tests zone operation for the current condi-
tions. You should perform a zone test after any change in
environment, equipment, or programming.
1. Close and secure the panel door.
2. Make sure all zones and sensors are in their secured
(non-alarm) state.
3. Press
. The display shows
8
4. Enter
+ installer code to initiate the zone test.
1
Testing the System
System Response
Indicates current system status
Disarms system to OFF
Arms system to PERIMETER/HOME
Arms system to FULL/AWAY
Manually reset smoke sensors
Check alarm history
Check event history buffer
Initiates a battery test
Initiates a zone test
Initiates a phone test
Initiates a fire test
.
SYSTEM MENU
BATTERY
*.
TO QUIT PRESS
.
SYSTEM MENU
45
Advertisement
Table of Contents
