Specific Phone Number Settings - Interlogix Advent Installation Instructions Manual

Buddy Dial Attempts
Default = 5
Set the number of dialing attempts (to central station) before a
buddy transmission is generated.
Setting the Number of Buddy Dial Attempts:
Once the item number has been entered, enter the number of
buddy dial attempts (0-11)* and press #.
* 0 = immediate transmit request, 11 = no transmit request.
No Phone Line
Default = 0 (Off)
Turn this setting on if there is no phone line connected to the
panel. When on, the panel will not check for phone line failure.
Turning No Phone Line Setting On/Off:
Once the item number has been entered, enter 1 to turn this setting
on (no phone line) or 0 to turn it off (phone line). Press # to apply
the new setting.
System Account Number 1
System Account Number 2
Defaults = 00000000
Enter an 8-digit system account number which will identify the
panel to the central station when reporting system events. System
Account Number 1 is reported on reporting phone 1 and its
backup. System account number 2 is reported on reporting phone
2 and its backup.
Account Number Format:
o o
for 0 enter 00 for 6 enter 06
o o
for 1 enter 01 for 7 enter 07
o o
for 2 enter 02 for 8 enter 08
o o
for 3 enter 03 for 9 enter 09
o o
for 4 enter 04 for A enter 10
o o
for 5 enter 05 for B enter 11
To Enter a System Account Number
1. Once the desired item number has been entered the current
system account number will be displayed.
Note
If a Dealer Access Code has been programmed, you will
be prompted to enter it.
2. Enter the new system account number using the list above.
For example, if you wanted the system account number to be
"123456AB," at the keypad you would enter "01, 02, 03, 04,
05, 06, 10, 11."
3. Press # and the touchpad displays the new system account
number.
Note
System account numbers must equal 8 characters. If
you enter less than 8 characters the panel will automati-
cally replace the blank spaces with leading zeros (0).
Commercial Burglary and Home Navigator System
17101
17069
17102
17103
o
for C enter 12
o
for D enter 13
o
for E enter 14
o
for F enter 15
Pager ID
Default = 00000
The Pager ID identifies the panel to pager-holders. Select the ID
to be sent with pager reports.
Setting System Pager ID:
Once the item number has been entered, enter the 5-digit Pager ID
(00000–99999) to be sent with pager reports and press #.
Interval Between Automatic Phone Test17034
Default = 1 (Commercial), 7 (Home Navigator)
Select the number of days between automatic phone test reports
to all enabled central station phone numbers. Entering 0 will dis-
able automatic phone test.
To Set Automatic Phone Test Interval:
Once the item number has been entered (17-034), enter
(0-255). Press # to apply the new setting.
BER OF DAYS

Specific Phone Number Settings

Specific phone number settings allow you to program cen-
tral monitoring station, downloader, and pager phone num-
bers.
Note
If a Dealer Access Code has been programmed, you will
be prompted to enter it when setting/changing specific
phone settings.
q Phone numbers 19–22 are central monitoring station
reporting phone numbers and function as follows:
19 = phone 1
20 = phone 1 backup
21 = phone 2
22 = phone 2 backup
q Phone numbers 23–24 are downloader phone numbers
and function as follows:
23 = phone 3
24 = phone 3 backup
q Phone numbers 25–40 are reporting pager phone num-
bers 1 through 16.
Central Monitoring Station and Downloader Phone
Number Settings
Phone Number Enable
Default = 0 (Off)
Select whether or not to enable the phone number. If on, the panel
will use the number when reporting or downloading. If off, the
number will be skipped.
To Turn Reporting Phone Number On/Off:
Once the item number has been entered (19001–24001), enter 1
to turn this setting on (call), or 0 to turn it off (no call). Press # to
apply the new setting.
Programming the Panel
17058
-
THE NUM
yy001
25