Perkins XGA 1600 Series Operation And Maintenance Manual page 52

52
Maintenance Section
Refill Capacities
Specification Requirements
The neat biodiesel must conform to "EN14214" or
"ASTM D6751" (in the USA) and can only be blended
in mixture of up to 20% by volume in acceptable
mineral diesel fuel meeting requirements that are
listed in table 7 or the latest edition of "EN590" and
"ASTM D 975" commercial standards. This blend is
commonly known as B20.
Biodiesel blends are denoted as "BXX" with "XX"
representing the content of neat biodiesel contained
in the blend with mineral diesel fuel (for example B5,
B10, B20).
In United States Biodiesel blends of B6 to B20 must
meet the requirements listed in the latest edition of
"ASTM D7467" (B6 to B20) and must be of an API
gravity of 30-45.
In North America biodiesel and biodiesel blends
must be purchased from the BQ-9000 accredited
producers and BQ-9000 certified distributors.
In other areas of the world, the use of biodiesel
that is BQ-9000 accredited and certified, or that is
accredited and certified by a comparable biodiesel
quality body to meet similar biodiesel quality
standards is required.
Engine Service Requirements with B20
Aggressive properties of biodiesel fuel may cause
debris in the fuel tank and fuel lines. The aggressive
properties of biodiesel will clean the fuel tank
and fuel lines. This cleaning of the fuel system
can prematurely block of the fuel filters. Perkins
recommends that after the initial usage of B20
biodiesel blended fuel the fuel filters must be replaced
at 50 hours.
Glycerides present in biodiesel fuel will also cause
fuel filters to become blocked more quickly. Therefore
the regular service interval should be reduced to 250
hours.
When biodiesel fuel is used, crank case oil and
aftertreatment systems may be influenced. This
influence is due to the chemical composition and
characteristics of biodiesel fuel, such as density and
volatility, and to chemical contaminants that can be
present in this fuel, such as alkali and alkaline metals
(sodium, potassium, calcium, and magnesium).
•
Crankcase oil fuel dilution can be higher when
biodiesel or biodiesel blends are used. This
increased level of fuel dilution when using biodiesel
or biodiesel blends is related to the typically
lower volatility of biodiesel. In-cylinder emissions
control strategies utilized in many of the industrial
latest engine designs may lead to a higher level
of biodiesel concentration in the engine oil pan.
The long-term effect of biodiesel concentration in
crankcase oil is currently unknown.
•
Perkins recommends the use of oil analysis in order
to check the quality of the engine oil if biodiesel
fuel is used. Ensure that the level of biodiesel in
the fuel is noted when the oil sample is taken.
Performance Related Issues with B20
Due to the lower energy content than the standard
distillate fuel B20 will cause a power loss in order
of 2 to 4 percent. In addition, over time the power
may deteriorate further due to deposits in the fuel
injectors.
Biodiesel and biodiesel blends are known to cause
an increase in fuel system deposits, most significant
of which are deposits within the fuel injector. These
deposits can cause a loss in power due to restricted
or modified fuel injection or cause other functional
issues associated with these deposits.
Note: Perkins T400012 Fuel Cleaner is most
effective in cleaning and preventing the formation
of deposits. Perkins Diesel Fuel Conditioner helps
to limit deposit issues by improving the stability of
biodiesel and biodiesel blends. Refer to "Perkins
Diesel Fuel System Cleaner" for more information.
General Requirements
Biodiesel has poor oxidation stability, which can result
in long-term problems in the storage of biodiesel.
Biodiesel fuel should be used within 6 months of
manufacture. Equipment should not be stored with
the B20 biodiesel blends in the fuel system for longer
than 3 months.
Due to poor oxidation stability and other potential
issues, it is strongly recommended that engines with
limited operational time either not use B20 biodiesel
blends or, while accepting some risk, limit biodiesel
blend to a maximum of B5. Examples of applications
that should limit the use of biodiesel are the following:
Standby generator sets and certain emergency
vehicles.
SEBU8455