Sony SRW-5001 Operation Manual page 91

Automatic time data changes during IN/OUT
point data entry or modification
The table below shows the automatic changes that
occur in time data when either the IN point or OUT
point is changed.
When IN point data is entered or modified:
Status of input data
The time sequence of the IN/
OUT point data is correct.
The time sequence of the IN/
OUT point data is not correct.
The OUT point has not been
input.
When OUT point data is entered or modified:
Status of the input data
The time sequence of the IN/
OUT point data is correct.
The time sequence of the IN/
OUT point data is not correct.
The IN point has not been
input.
Changing Tk data
Use the cursor buttons to move the cursor to the take
data to be changed. Then use the numeric buttons to
change the value. Note that values from 0 to 255 can
be entered. Or, move the cursor to the take data, and
press the [F4] (CHANGE DATA) button or the +
button repeatedly to increase the value in increments
of 1. Press the – button repeatedly to decrease the
value in increments of 1. Note that the value cannot
go below 0.
Copying data
Use the cursor buttons to move the cursor to the
destination Mrk or Tk data, and press the RCL button.
The Tk data from the line above is copied to the
selected line.
IN point OUT point
The data is The data is
changed. unchanged.
The data is The data is
changed. deleted.
The data is The data is
changed. unchanged.
IN point OUT point
The data is The data is
unchanged. changed.
The data is The data is
unchanged. unchanged.
The data is The data is
unchanged. changed.
Changing Cut data
Use the cursor buttons to move the cursor to the cut
data to be changed, and then enter the new data using
the numeric buttons and +/– buttons. Pressing the –
button enters the tilde (~). Press the numeric buttons
while pressing down the SFT button to enter uppercase
letters (A to J). Note that a maximum of four
characters can be entered.
Or, do the procedure below to change the data.
2 4 6
1
Press the cursor buttons to move the cursor to the
cut data to be changed.
To move the cursor using the numeric buttons
Enter the line number using the numeric buttons.
Then press the [F9] (CUENUM POINT) button.
The cursor will move to the line specified by the
numeric buttons.
2
Press the [F4] (CHANGE DATA) button.
R E C D A T E [ 2 0 0 3 / 0 2 / 2 5 ]
C U T N o . E D I T
T I T L E [ i s p l a y S a m p l e
N o . T a p e F o r m a t D u r a t i o n
_
0 5 9 i 1 0 8 0 4 2 2 0 1 : 0 0 : 3 6 : 0 6
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
1 5 9 i 1 0 8 0 4 2 2
a b c d e f g h j i k l m n o p q r s t u v w x y z
0 1 2 3 4 5 6 7 8 9 [ ] ( ) < > @ + - * = ! ? : ;
$ # % & , . " \ ^ _ ' / ~ { }
S P A C E B A C K S E T
S P A C E L E T T E R
1,3
E O S [ 0 1 : 0 1 : 0 2 : 0 8 ]
] R e s t 1 0 0 %
- - -
0 1 : 0 0 : 3 6 : 0 6 - - -
' H D 1 D 2 C A M
C A N C E L S A V E /
E X I T
(Continued)
4-51
Chapter 4 Menu Settings