Operating Other Manufacturers' Equipment; Changing The Preset Signal Codes - JVC RX-DP15BC Instructions Manual

Operating Other Manufacturers' Equipment

You can use this remote control supplied for operating other manufacturers' components, either by changing the
preset signal codes or by using the learning function (see page 78).
IMPORTANT:
• To operate the other component(s) using the RF signals emitted
from this remote control, the IR signal transmitter and the RF rod
antenna must be connected to this receiver.
– Place the IR signal transmitter so that it is aimed at the remote
sensor(s) on the target component(s).
– The RF signal-reachable distance may differ depending on the
operating conditions and circumstances.
– The IR signal transmitter can send signals at a distance of 3 m.
When using the remote control:
– Set the ZONE 1/ZONE 2 (LEARN/TRANSMIT) selector to "ZONE 1" or
"ZONE 2" correctly.
LEARN TRANSMIT
ZONE 1 ZONE 2
– Set the TV operation mode selector to "TV" or
"CATV/DBS" correctly.
To operate TV, set it to "TV."
To operate the CATV converter or the DBS tuner, set
it to "CATV/DBS."
– Check the indication shown on the remote's display
when you press a button—this indicates the remote control
operation mode together with multi-room operation mode (either
ZONE 1 or ZONE 2) for a while.
LEARN TRANSMIT
STANDBY ON
ZONE 1 ZONE 2
ZONE 1 ZONE 2 TV/CATV/DBS VCR 1
ON/OFF ON/OFF
STANDBY/ON STANDBY/ON
ZONE 1
Ex. When you press VCR1
with ZONE 1/ZONE 2
(LEARN/TRANSMIT)
selector set to "ZONE 1."
CAUTION:
When replacing the batteries, finish changing them without delay;
otherwise, preset manufacturers' codes will be reset.
LEARN TRANSMIT
ZONE 1 ZONE 2
TV
CATV/
DBS
LEARN TRANSMIT
STANDBY
ON
ZONE 1 ZONE 2
ZONE 1 ZONE 2 TV/CATV/DBS
VCR 1
ON/OFF ON/OFF
STANDBY/ON STANDBY/ON
ZONE 2
Ex. When you press VCR1
with ZONE 1/ZONE 2
(LEARN/TRANSMIT)
selector set to "ZONE 2."

Changing the Preset Signal Codes

By changing the transmittable signals from preset ones to the other
manufacturers', you can operate the other manufacturer's
components using this remote control.
• When operating the other manufacturers' components, refer also
to the manuals supplied with them.
To change the transmittable signals for
operating another manufacturer's TV
1. Set the TV operation mode selector to
"TV."
2. Press and hold TV/CATV/DBS
(STANDBY/ON).
3. Press TV/DBS.
Remote's display
4. Enter a manufacturer's code
using buttons 1–9, and 0.
See page 76 to find the code.
5. Release TV/CATV/DBS
After setting the TV operation mode selector to "TV," you can
perform the following operations on the TV:
TV/CATV/DBS (STANDBY/ON)
: Turns on or off the TV.
TV VOL +/– : Adjusts the volume.
TV/VIDEO : Sets the input mode (either TV or VIDEO).
After pressing TV/DBS (with the TV operation mode selector
set to "TV"), you can perform the following operations on a TV:
CHANNEL +/– : Changes the channels.
1–10, 0, 100+ (+10) : Selects the channels.
Number button 10 will function as
the ENTER button if your TV
requires pressing ENTER after
selecting a channel number.
Notes:
• Refer to the manual supplied for your TV.
• All the buttons listed above may not be used for some TVs.
• If you cannot change the channels of some TVs by pressing
number buttons, press CHANNEL +/– .
6. Try to operate your TV by pressing
TV/CATV/DBS (STANDBY/ON).
When your TV turns on or off, you have entered
the correct code.
If more than one code is listed for your brand of TV, try each
one until the correct one is entered.
TV
CATV/
DBS
TV/CATV/DBS
STANDBY/ON
TV/DBS
EFFECT
1 2 3
LIVENESS
4 5 6
7 8 9
/P
10 0 10
+
100 +
RETURN FM MODE
(STANDBY/ON).
TV/CATV/DBS
STANDBY/ON
74