Basic Operating Procedure For Zone 2 - JVC RX-DP15BC Instructions Manual

Basic Operating Procedure for Zone 2

The sources and functions available for the Zone 2
operations are limited.
For more details on the Zone 2 operations, see "Zone 2 (Sub-
room) Operations" on pages 29 to 32.
On the unit:
1. Press (STANDBY/ON).
The STANDBY lamp goes off, and the ZONE 1 ON/OFF lamp
lights up.
The front door moves down so that the source selecting buttons
appear, and the buttons and controls on the unit work for the
Zone 1 operations.
• For more details, see "Turning the Power On and Off (Standby)
and Selecting the Zone 2 Operations" on page 29.
STANDBY
STANDBY/ ON
2. Press ZONE 2 ON/OFF so that the
ZONE 2 ON/OFF lamp lights up.
3. Press DOOR DOWN so that you can use the
other buttons inside the front door.
DOOR
DOWN
To close the front door, press
DOOR UP once or twice.
The front door moves up in two steps.
4. Press ZONE 2 CONTROL so that
"ZONE 2" and the previously
selected Zone 2 source name
appear on the display.
Now the buttons and controls on the unit work for the Zone 2
operations.
The last Zone 2 source appears.
5. Select and play a source.
The sound comes out of the Zone 2 front speakers.
• If no sound comes out of the Zone 2 front speakers, see
page 32.
DVD DVD MULTI VCR 1 VCR 2 TV/DBS VIDEO
Notes:
• You cannot select "DVD MULTI" and "EXT 7.1CH" for Zone 2.
• When "TV" has been assigned as the source to the TV/DBS
button, it does not work. To change the source name, see
"Changing the Source Name" on page 27.
21
ZONE 1
ON/OFF
ZONE 2
ON/OFF
ZONE 2
CONTROL
SPEAKERS 1 ZONE 2
VOLUME
The Zone 2 volume
level appears.
CD PHONO TAPE/MD CDR FM/AM
6. Turn MASTER VOLUME to
adjust the volume level of the
sound through the Zone 2 front
speakers.
Note:
When "ZONE2PREOUT" is set to "FIX" on the ZONE 2/
SPEAKERS 2 submenu (see page 43), the MASTER VOLUME
control will not work for adjusting the volume level of the sound
through the ZONE2 PREOUT jacks.
From the remote control:
When operating the receiver using the remote control, the
display on the unit always shows the Zone 1 source information
though you are operating it for the Zone 2 source.
1. Set ZONE 1/ZONE 2 (LEARN/
TRANSMIT) selector to "ZONE 2."
Now the buttons and controls on the remote
control work for the Zone 2 operations.
2. Press AUDIO (ON).
The STANDBY lamp on the unit goes off, and the ZONE 2 ON/
OFF lamp on the unit lights up.
STANDBY
ON
3. Select and play a source.
DVD
VCR 1
TV/DBS
The sound comes out of the Zone 2 front speakers.
• If no sound comes out of the Zone 2 front speakers, see
page 32.
Notes:
• You cannot select "DVD MULTI" and "EXT 7.1CH" for Zone 2.
• When "TV" has been assigned as the source to the TV/DBS
button, it does not work. To change the source name, see
"Changing the Source Name" on page 27.
dB dB
4. Press VOLUME +/– to adjust the
volume level of the sound through
the Zone 2 front speakers.
EXT 7.1CH
Note:
When "ZONE2PREOUT" is set to "FIX" on the ZONE 2/
SPEAKERS 2 submenu (see page 43), the VOLUME +/– control
will not work for adjusting the volume level of the sound through
the ZONE2 PREOUT jacks.
MASTER VOLUME
Down
LEARN
ZONE 1
ZONE 2
ON/OFF
DVD MULTI PHONO CD
CDR
VCR 2 TAPE/MD
VIDEO FM/AM EXT 7.1CH
VOLUME
Up
TRANSMIT
ZONE 2