Sony BVP-900 Series Product Information Manual page 100

10
Location and Function of Parts and Controls
continuously changes while either button remains
pressed.
In Shutter mode (when the ECS button is not illuminated): The
denominator of the selected step shutter speed is
displayed in the window. Press to select the desired
shutter speed. The speed increases when the
button is pressed and decreases when the
button is pressed. It continuously changes while either
button remains pressed.
5) Filter control block
a
b
ND
(a) ND (ND filter select) display
Indicates the number corresponding to the selected the ND filter.
1: Clear
2: 1/4 ND
3: 1/8 ND
4: 1/16 ND
5: 1/64 ND
(b) ND (ND filter select) buttons
Once either button is pressed, both buttons illuminate. Each time
you press the buttons, the ND filter setting changes as follows:
: 1 2 3 4 5 1 ...
: 5 4 3 2 1 5 ...
The filter setting changes when either button remains pressed.
(c) CC (color temperature conversion filter select) display
Indicates the number corresponding to the selected CC filter.
A: Cross filter
B: 3200 K (clear)
C: 4300 K
D: 6300 K
E: 8000 K
(d) CC (color temperature conversion filter select) buttons
Once either button is pressed, both buttons illuminate. Each time
you press the buttons, the CC filter setting changes as follows.
: A B C D E A ...
: E D C B A E ...
The filter setting changes while either button remains pressed.
Note Once any of the (b) and (d) buttons has been pressed, all the four
buttons illuminate, enabling both the ND and CC filter selections.
6) MONITOR SELECT buttons
Press to select the output signal from the WF1 OUTPUT connector
of the CCU-700A/700AP. The signal corresponding to the illuminated
button is output.
SEQ: (sequential): When this button is pressed, you can monitor
the waveforms of the three R, G and B signals, in sequence,
on a monitor connected to the WF1 OUTPUT connector.
ENC (encode): When this button is pressed, the SEQ circuits for
the WF1 OUTPUT are turned off and the ENC
signal is output from the WF1 OUTPUT
connector.
99
(up)
(down)
c
d
CC
Note The output from the PIX1 OUTPUT connector is fixed to ENC.
7) Camera number/tally indication window
The number of the camera being controlled from this panel is
displayed in orange. When a red tally signal is sent to the camera,
the number is displayed in black and the background of the number
illuminates in red. When a green tally signal is sent to the camera,
the number is displayed in black and the background of the number
illuminates in green. When both the red and green tally signals are
sent simultaneously, the left half of the background illuminates in red
and the right half illuminates in green.
8) ALARM indicator
Illuminates when a problem occurs in the camera system and the
self-diagnostic function activates at the camera or the CCU-
700A/700AP.
9) CALL button
Press to send a call signal to the camera, on which the CALL button
is illuminated. The tally lamps on the camera and the red tally lamp
on the CCU-700A/700AP are illuminated if not already lit, or are
turned off if already illuminated. When the CALL button on the
camera is pressed, the call button on this panel illuminates and a
buzzer sounds.
10) PANEL ACTIVE button
Press and illuminate the button to permit this panel to control the
camera system (Panel active status). The IRIS/MB ACTIVE button
also illuminates.
11) Power and output signal select block
a
CAM PW TEST
(a) CAM PW (camera power) button
Press and illuminate this button to turn the power supply to the
camera ON.
Press and illuminate this button to turn the power supply to the
camera ON. (The button flashes until the camera is ready for
transmission.) When you press this button again, it starts flashing
and the power supply is turned off.
(b) Signal output select buttons
Press and illuminate one of these buttons to activate the test signal
generator of the camera and send the respective signals.
TEST: To send a sawtooth signal to test the video circuits.
BARS: To send a color bar signal.
Note The BARS button takes priority to the TEST button. If the BARS
button is illuminated, press the button to turn the illumination off before
pressing the TEST button.
12) AUTO SETUP block
a
b
AUTO SETUP
SKIN DTL LEVEL START/
AUTO HUE BREAK
(a) Auto adjustment item select buttons
Press and illuminate these buttons to select the items to be adjusted
b
BARS
c
d
WHITE BLACK