A. Copy Mode - Sharp AR-203E Service Manual

A. Copy mode

Program
Program name
number
1 AUTO CLEAR
2 PREHEAT MODE
3 AUTO SHUT-OFF
4 AUTO SHUT-OFF
TIME
7 LAYOUT IN 2IN1
8 OFFSET
FUNCTION
9 ROTATE ORIG.
IMAGE
(AR-208D only)
10 AE/TEXT
RESOLUTION
11 2-SIDED COPY
MODE
(AR-208D only)
12 MARGIN WIDTH
13 MEM. FOR
PRINTER
14 AUTO KEY REPEAT
15 KEY PRESS TIME
16 KEY TOUCH
SOUND
17 SOUND AT
DEFAULT
18 TONER SAVE
MODE
Setting codes
(factory default setting
appears in bold)
1: 10 SEC. • Auto clear time automatically returns the copy settings to the initial settings
2: 30 SEC.
3: 60 SEC.
4: 90 SEC. • This program is used to select the period of time. Auto clear time can also
5: 120 SEC.
6: OFF
1: 30 SEC. • This function automatically switches the machine to a low power
2: 1 MIN.
3: 5 MIN.
4: 30 MIN.
5: 60 MIN.
6: 120 MIN.
7: 240 MIN.
1: ON • Use this setting to enable or disable auto power shut-off mode.
2: OFF
1: 5 MIN. • This function automatically switches the machine to a state that consumes
2: 30 MIN.
3: 60 MIN.
4: 120 MIN.
5: 240 MIN.
1: PATTERN 1 • Use this setting to select the layout pattern when two original pages are
2: PATTERN 2
1: ON • When enabled, this function offsets the position of each set of copies in the
2: OFF
1: ON • When two-sided copying is performed, this function rotates the image on
2: OFF
1: 300dpi • This setting is used to change the copy resolution in AUTO and TEXT
2: 600dpi
1: HI-SPEED • If the memory fills up when two-sided copying is performed, "NORMAL"
2: NORMAL
1: 1/4" • Use this setting to set the margin width.
2: 1/2"
3: 3/4"
4: 1"
1: 30% • Use this to change the proportion of machine memory used for printer
2: 40%
3: 50%
4: 60%
5: 70%
1: ON • Use this setting to select whether or not holding down a key causes
2: OFF
1: NORMAL • Use this setting to select how long a key must be pressed for the input to be
2: 0.5 SEC.
3: 1.0 SEC.
4: 1.5 SEC.
5: 2.0 SEC.
1: LOW • This sets the volume of beep signals.
2: HIGH
3: OFF
1: ON • Use this to sound a beep when a base setting is selected.
2: OFF
1: ON • This mode reduces toner usage by about 10% when copying. Toner save
2: OFF
AR-203E/5420/M200/M201 USER PROGRAM 12 - 3
if no keys are pressed for a preset period of time following the end of a copy
job.
be disabled.
consumption state if the set duration of time elapses without the machine
being used when the power is on. The power save indicator lights up,
however, the keys on the operation panel can be used. Normal operation
automatically resumes when a key on the operation panel is pressed, an
original is placed, a print job is received.
even less power than preheat mode if the set duration of time elapses
without the machine being used when the power is on. All lights except the
power save indicator go off. To resume normal operation, press the
[START] key ( ). Normal operation also resumes automatically when a
print job is received or scanning is begun from a computer. While in auto
power shut-off mode, no keys (except the [START] key (
copied onto a single sheet of paper.
output tray in copy mode, and each print job in printer mode.
the back of the original. This is convenient when binding the copies at the
top (tablet binding).
mode from 600 x 300 dpi to 600 x 600 dpi (high-quality mode). Scanning is
slower when high-quality mode is used.
can be selected to make copying possible. However, "NORMAL" results in
a slower copying speed. Normally "HI-SPEED" is selected to enable fast
two-sided copying.
mode.
repeated input of the key. For keys that normally cause a set value to
decrease or increase when held down (for example, the [
[ ] key ( )), this program can be used to have the set value not
change when the key is held down.
accepted. By selecting a longer time, you can prevent settings from being
changed by the accidental pressing of a key.
mode is effective when the exposure mode is AUTO or TEXT.
Explanation
)) can be used.
] key ( ) or