User Programs (Ar-M200/M) - Sharp AR-203E Service Manual

Program
Mode
No.
25 Copy effective paper width
setting function (Bypass
tray)
26 Copy effective paper width
setting function (Tray)
28 Selection of copy start
state (Polygon rotation on/
off)
29 Fusing temperature
setting when the bypass
tray is used
∗ Factory default settings are indicated with an asterisk (*).
5) Press the start ( ) key. The right-hand number in the display
will be steadily lit and the entered value will be stored.
Note: To change the setting or to set another mode, press the
clear key. The unit will return to step 2).
6) Press the light ( ) key to return to the normal copy mode.
4. User programs (AR-M200/M201)
1) Press the [MENU] key and then press the [OK]/[ENTER] key.
In printer mode, the user programs are accessed by simply
pressing the [MENU] key.
MAIN MENU
1:USER PROGRAM
1 1 2
2 2
2 1 1
]
2) Press the [ ] key [
that you wish to configure in the USER PROGRAM items, and
then press the [OK]/[ENTER] key.
• See "1. User programs" for the program name and program
code.
• You can also select a program by directly entering the pro-
gram number with the numeric keys.
USER PROGRAM
2:PREHEAT MODE
1 1 2
2 2
2 1 1
Parameters
*1 → Large (A4 width/
LETTER), 2 → Small (B5R
width/INVOICE)
*1 → Large (A4 width/
LETTER), 2 → Small (B5R
width/INVOICE)
*1 → ON, 2 → OFF
1 → Low, *2 → High
MAIN MENU
1:USER PROGRAM
]
or [ ] key [ to select the item
USER PROGRAM
2:PREHEAT MODE
AR-203E/5420/M200/M201 USER PROGRAM 12 - 2
3) Press the [ ] key [ ] or [
ting of the selected item.
• See "1. User programs" for the program code.
PREHEAT MODE
1:1 MIN
1 1 2
2 2
2 1 1
NOTE:
• If you mistakenly select the wrong item, press the [Clear] key
( ) and repeat the procedure from step 2).
• To cancel a setting for a user program, press the [MENU] key.
4) Press the [OK]/[ENTER] key.
Your selection appears briefly and then the previous screen
appears.
NOTE:
When "AE LEVEL ADJUST" is selected in the user programs and
the [OK]/[ENTER] key is pressed, the automatic exposure
adjustment screen appears. Adjust the exposure and press the
[OK]/[ENTER] key.
Audible signals (key entry beep, invalid key beep, base
setting beep)
The machine sounds three different types of beep signals: a key
entry beep that sounds when a valid key is pressed, an invalid
key beep that sounds when an invalid key is pressed, and a base
setting beep that sounds when a setting is the same as the base
setting (base settings are explained below). The base setting
beep is initially disabled. If you wish to enable the base setting
beep, see "SOUND AT DEFAULT". If you wish to change the vol-
ume of the beep signals or disable them, see "KEY TOUCH
SOUND".
The beep patterns of each type of beep signal are as follows:
Key entry beep: One beep
Base setting beep: Three beeps
Base settings
The base settings are preset standard selections for each copy
setting. The base settings are as follows:
Copy ratio: 100%
Light and Dark level: Center
] key [ ] to change the set-
PREHEAT MODE
1:1 MIN
Invalid key beep: Two beeps
Paper feed location:
Tray 1 (Upper paper tray)
AUTO/TEXT/PHOTO: AUTO