Rear Section; Bottom Section; Preparations; Basic System - JVC KA-HD250 Instructions Manual

INTRODUCTION
Controls, Indicators and Connec-
tors (Cont'd)

Rear Section

g
INTERCOM DC INPUT
PUSH
INTERCOM MIC INTERCOM LEVEL CALL
ON
OFF
MIN MAX
h i j k l
g[TALLY] TALLY Lamp
Lights up green when in stand-by (preview). Lights up red
when the camera image is selected with the remote con-
troller.
h[INTERCOM] Intercom Input Terminal (XLR 5 Pin)
Input terminal for intercom headset. (Dynamic only)
Recommended headset: DT109 (Beyerdynamic)
Signal
1 5
1 MIC (H)
2 MIC (C)
2 4
3 EAR (C)
3 4 EAR (H) – LEFT
(Surface profile)
5 EAR (H) – RIGHT
i[INTERCOM MIC] Intercom Mic [ON/OFF] Switch
[ON/OFF] switch for intercom headset microphone. Set to
[ON] to use the headset microphone.
j[INTERCOM LEVEL] Intercom Receiver Volume
Use for adjusting the intercom headset receiver volume
level.
8
k[CALL] CALL button/Power indicator
Lights green when the studio adapter is turned on.
However, lights up amber when the camera is off.
Press to send call signal to the remote control unit opera-
tor if intercom headset is not in-use.
Button indicator changes from green to red when the but-
ton is pressed.
When this button is pressed and held down, call signal is
sent to the remote control unit and the [TALLY] indicator
blinks. Once the [CALL] button is released, call signal is
no longer sent and the [TALLY] indicator of the remote
control unit turns off.
l[DC INPUT] DC Power Input Terminal (XLR 4 Pin)
Connect DC power to this terminal if Remote Control Unit
RM-P210 is not connected. For DC power supply, use the
IDX IA-60a or VL-2PLUS.
CAUTION
When cable is connected to the DC INPUT terminal while
supplying power from the RM-P210, power will be inter-
rupted.
Turn off connected devices when connecting a cable to the
DC INPUT terminal.

Bottom Section

m
mScrew Holes for Mounting Tripod

PREPARATIONS

Basic System

View Finder
DM-3106 (Astrodesign)
V-R70P-HAD (Marshall Electronics)
VF BRIGHT
USER 1 USER 2 USER 3 VF OUTPUT
ND FILTER
2
1
MENU
STATUS
WHT.BAL
AUTO AUDIO AUTO
LEVEL
CH-1 CH-2
ON OFF
POWER REC
HD CAMERA RECORDER
GY-HD250/GY-HD251
STUDIO KIT
KA-HD250
PROMPTER OUTPUT
terminal
Monitor
Dolly
Power is supplied by the Remote Control Unit RM-P210 via the 26 pin camera cable when in-use. If the Remote Control Unit
RM-P210 is not in-use, use AC power adapter.
View Finder
VF-P400
Conversion plug
VF OUTPUT
terminal terminal
Headset
(BNC × 3) (Round 20-Pin)
DT109 (Beyerdynamic)
INTERCOM terminal
DC cable
AC Power Adapter
IA-60a, VL-2PLUS (IDX)
DC INPUT terminal
RM terminal REMOTE cable
Tripod
REMOTE CONTROL UNIT RM-P210
TALLY CALL FULL AUTO F1 F3 MENU/SHUTTER GAIN PAINT WHITE AUTO MASTER BLACK
SHUTTER STEP W.BAL
HIGH B
SHUTTER VARIABLE MID A
BARS F2 F4 MENU PUSH-ON PUSH-ON R B
LOW PRESET
GAIN
INTERCOM DOWN UP DOWN UP
LEVEL
Remote Control Unit
RM-P210
Headset
DT109 (Beyerdynamic)
IRIS POWER
I
AUTO
MANU
O
CLOSE OPEN
9