Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Instruction Manual
e_ka250.book Page 1 Tuesday, September 5, 2006 11:13 AM
© 2006 Victor Company of Japan, Limited
STUDIO ADAPTER
KA-HD250
For Customer Use:
Enter below the Serial No. which is located on the body.
Retain this information for future reference.
Model No.
KA-HD250
Serial No.
LST0445-001A
INSTRUCTIONS
LST0445-001A
Advertisement
Table of Contents
Related Manuals for JVC GY KA-HD250
Summary of Contents for JVC GY KA-HD250
- Page 1 e_ka250.book Page 1 Tuesday, September 5, 2006 11:13 AM © 2006 Victor Company of Japan, Limited STUDIO ADAPTER KA-HD250 For Customer Use: Enter below the Serial No. which is located on the body. Retain this information for future reference. Model No. KA-HD250 Serial No.
-
Page 2: Important Safeguards
e_ka250.book Page 2 Tuesday, September 5, 2006 4:10 PM INTRODUCTION These are general important Safeguards and certain items may not apply to all appliances. Important Safeguards Read all of these instructions. Save these instructions for later use. All warnings on the product and in the operating instructions should be adhered to. -
Page 3: Safety Precautions
Consult the dealer or an experienced radio/TV technician for help. CAUTION: CHANGES OR MODIFICATIONS NOT APPROVED BY JVC COULD VOID USER’S AUTHORITY TO OPERATE THE EQUIPMENT. NOTE: The rating plate (serial number plate) is on this unit. -
Page 4: Safety Precautions
e_ka250.book Page 4 Tuesday, September 5, 2006 4:10 PM INTRODUCTION Safety Precautions (For Europe) WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. This unit should be used with 12 V DC only. CAUTION: To prevent electric shocks and fire hazards, do NOT use any other power source. -
Page 5: Table Of Contents
e_ka250.book Page 5 Tuesday, September 5, 2006 4:10 PM Thank you for purchasing this product. (These instructions are for: KA-HD250U.) Before operating this unit, read the instruction manual care- fully in order to make sure that the best possible perfor- mance is obtained. -
Page 6: Operating Precautions
: Pages or items to refer to. Notation used in this manual • The copyright for this manual is property of JVC. Unau- thorized reproduction or publication of this manual in part or in whole is strictly forbidden. -
Page 7: Controls, Indicators And Connectors
If no abnormalities are detected, press the breaker switch before turning the power on again to put this unit in the operating status. If this unit still does not function properly, consult your JVC-authorized dealer. 7[VF OUTPUT] (Y/P /RGB) BNC×3 Component output terminal for viewfinder.Use when con-... -
Page 8: Rear Section
e_ka250.book Page 8 Tuesday, September 5, 2006 4:10 PM INTRODUCTION Controls, Indicators and Connec- tors (Cont’d) Rear Section INTERCOM PUSH INTERCOM MIC INTERCOM LEVEL CALL g[TALLY] TALLY Lamp Lights up red when GY-HD250 is in RECORDING mode. Blinks red when preparing RECORDING mode and lights up green when in stand-by. -
Page 9: Preparations
e_ka250.book Page 9 Tuesday, September 5, 2006 4:10 PM PREPARATIONS Basic System DM-3106 (Astrodesign) V-R70P-HAD (Marshall Electronics) VF BRIGHT USER 1 USER 2 USER 3 ND FILTER MENU STATUS WHT.BAL AUTO AUTO AUDIO LEVEL CH-1 CH-2 POWER HD CAMERA RECORDER GY-HD250/GY-HD251 PROMPTER OUTPUT terminal... -
Page 10: Installation
e_ka250.book Page 10 Tuesday, September 5, 2006 4:10 PM PREPARATIONS Installation Mounting on a Tripod Use the screw holes on the bottom to mount on a tripod. There are multiple screw holes. Use well-balanced holes to mount to a tripod. Mounting the Camera Prepare the camera as follows before mounting. -
Page 11: Connecting Cables
e_ka250.book Page 11 Tuesday, September 5, 2006 4:10 PM Connecting Cables Connect the cables for this device to the camera. GENLOCK/AUX IN HD/SD TC IN TC OUT REMOTE DC INPUT STUDIO Connect the cable for this device to the camera terminal. Cable (type) Camera terminal... -
Page 12: Connecting To Remote Control Unit Rm-P210
e_ka250.book Page 12 Tuesday, September 5, 2006 4:10 PM PREPARATIONS Connecting to Remote Control Unit RM-P210 Connection Switch off RM-P210 power supply before attempting the con- nection. Connecting the RM-G210 Connect this unit’s RM multi-pin connector and RM-P210 using the 26 pin camera cable. Length of the camera cable should not be longer than 100 m. -
Page 13: Operation
e_ka250.book Page 13 Tuesday, September 5, 2006 4:10 PM Operation Turn the RM-P210 on. Turn the [POWER] switch of the camera remote control unit to [ON]. CALL button lights up green when the power is turned on. After the [POWER] switch is turned on, cam- era remote control unit can be operated after about 30 seconds. -
Page 14: Notes On Operating Rm-P210
e_ka250.book Page 14 Tuesday, September 5, 2006 4:10 PM PREPARATIONS Notes on Operating RM- P210 Some actions are not compatible when setting the GY- HD250 with RM-P210 menu operations. (G: Action available ×: No action) Function DETAIL (CONTOUR) IRIS MANU AUTO WHITE BAL MANU... -
Page 15: Others
e_ka250.book Page 15 Tuesday, September 5, 2006 4:10 PM OTHERS Specifications RM Multi-pin connector: Composite video signal output (Either Y/P , RGB or YC separate output signal can be selected) PROMPTER output: PROMPTER video signal output (composite signal) Operating temperature range: •...