Page 1
ELECTRONIC CASH REGISTER ER-260 SERIES SERVICE Manual ELECTRONIC CASH REGISTER C O N T E N T S Precaution Statements Product Specifications Installation and Operation Disassembly and Assembly Troubleshooting Exploded Views and Parts List PCB Layout and Parts List Block diagram Wiring Diagram 10.
Page 2
About this Manual This service manual describes how to perform hardware service maintenance for the SAM4S ER-260 Series Electronic Cash Register. Notes Notes may appear anywhere in the manual. They describe additional information about the item. Precaution symbols . Indicates a Safety Precaution that applies to this part component.
Page 3
This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or machine readable from without prior written permission of Shin Heung Precision . SAM4S ER-260 SERIES Service Manual First edition. September 2006. V1.0 Printed in KOREA...
Page 4
Overview of this ECR This ECR is a microprocessor-based system, using a 8 bits microprocessor. This service manual provides the technical information for many individual component systems, circuits and gives an analysis of the operations performed by the circuits. If you need more technical information, please contact our service branch or R&D center.
Remplacer uniquement avec une batterie du même recommended by the manufacturer. type ou d’un type équivalent recommandé par le Dispose used batteries according to the constructeur. manufacturer’s instructions. Mettre au rebut les batteries usagées conformément aux instructions du fabricant. SAM4S ER-260 SERIES...
Page 7
4. Do not use freon-propelled chemicals. These can carpeted floor can generate enough static generate electrical charges that damage ESDs. electricity to damage an ESD. 5. Use only a grounded-tip soldering iron when soldering or unsoldering ESDs. SAM4S ER-260 SERIES...
: 0℃ ~ 45℃ Condition • humidity : 30% ~ 80% RH Dimensions(mm) With Small Drawer • 325(W) X 420(D) X 226(H) Weight • 7.4 Kg (Set Only), 8.6Kg (with Packing) With Small Drawer Table2-1 General Specifications SAM4S ER-260 SERIES...
Page 9
① Printer Cover ② Key Board (Raised or Flat type) ③ Drawer ④ Customer 10-Digits VFD Display ⑤ Operator Display (10-Digits VFD) or 16x2 line LCD ⑥ Mode Key ⑦ RS-232 Serial I/F Connector Figure2-2 Location Feature SAM4S ER-260 SERIES...
Page 10
Line Feed Motor • Thermistor Head Temperature Sensor • Reflecting Photo Sensor Paper-End Sensor • 50km / 5×10 pulse Reliability Life • 38.0 (W) ×72.0 (D) ×15.6 (H) Dimension (mm) • Approx. 50 g Weight Table2-2 Thermal Printer Specification SAM4S ER-260 SERIES...
Page 11
: AC 220V/240V, 50Hz (Min : 195.5V, Max : 264.5V) • Regularity Power Consumption : Approx. 20W • AC 19V 2.3A (Wire Color : Blue-Blue) Power Transformer Output Voltage Output • AC 24V 0.15A (Wire Color : Red-Red) Table2-5 Power Specification SAM4S ER-260 SERIES...
Page 12
• 8 Bit Data Word Length • None Parity • DB9P Female (I/F PBA Side) Connector For Bar Code Reader • VCC(+5V/150mA) is supplied at 9Pin of D-SUB Connector. Voltage Supply or other devices Table2-6 RS-232C Specification SAM4S ER-260 SERIES...
Page 14
When DTR/DSR flow control is select, before transmitting a data, the ECR checks whether the host is BUSY or not. If the host is BUSY, ECR does not transmit a data to the host. If the host is not BUSY, ECR transmits a data to the Host. The host is the same. SAM4S ER-260 SERIES...
3 Installation and Operation 3-1 System Configuration 3-1-1 Configuration Figure 3-1. System Configuration SAM4S ER-260 SERIES...
Page 17
3-2 (B)) 3. Insert the end of the paper into the paper slot.(Fig 3-2 (C)) 4. Close the paper lever. ( ER-260 Series is possible to feed automatically when you rock the paper levers insert paper.). (Fig 3-2 (D)) 5.
Page 18
Wind the paper two or three turns around the spool shaft and install the spool in the mount 1. If you use the ER-260 Series with 1-station, refer to below figure. (Fig 3-3 (F)) 2. If you use the ER-260 Series with 2-stations, refer to below figure. (Fig 3-3 (G)) Figure 3-3.
Page 19
3-2-5 Supplies Item Description Remark Paper Roll 1 EA VD, REG, X, Z, P, C : NON FISCAL Mode Key REG, X, Z, P, C : FISCAL User Manual 1 EA Spool 1 EA Table 3-2. Supplies SAM4S ER-260 SERIES...
Off, Register(REG), Manager(X), Clear Totals(Z) Void, Off, Register(REG), Manager(X), Clear Totals(Z), Program(P) Void, Off, Register(REG), Manager(X), Clear Totals(Z), Program(P), Service Mode(S) Table3-4 Key Function Note : The Key can be removed from the key lock in the OFF or REGISTER position. SAM4S ER-260 SERIES...
Page 21
3. Installation and Operation 3-3 Operation 3-3-2 Key Board Matrix 1) 1-station model Figure 3-6. 1-Station Model Key Board 2) 2-station model Figure 3-7. 2-Station Model Key Board SAM4S ER-260 SERIES...
4. While continuing to hold the “CASH” key, plug the register into a power source. 5. The message "****** INITIAL CLEAR ******” prints when the initial clear is complete. ****** INITIAL CLEAR ****** Figure3-8. Initial Clear Key & Print Sheet(ER-260) SAM4S ER-260 SERIES...
Page 23
************************************************** RAM ALL CLEAR OK ! ************************************************** ER-260 EPROM INFO. VERSION : STD CHECKSUM : d2e1 SRAM SIXE : 1MBits SEP 08 2006 17:55 01-09-2006 000001 Figure3-9. All Clear Key Sequence & Print Sheet SAM4S ER-260 SERIES...
2. Press Press ‘1’, ‘4’ and ‘SUB TOTAL’ key on key board. 3. If error occurs, the message (232 NOGOOD) is displayed on VFD and the Buzzer beep. Then Press “Clear” key. Note : When the ports is unconnected the cable , the Error occur. SAM4S ER-260 SERIES...
2. Separate the JOURNAL PRINTER(B5) & HARNESS GND(B38), REAR LEVER-LOCK(B4). (Page6-3) 3. Separate the harness(ⓓ) from the PBA-JOURNAL(B28). (Page6-3) 4. Remove the two screws(B29) and Separate the PBA-JOURNAL(B28) from the ASS’Y CASE UPPER (B). (Page6-3) 5. Separate the harness(ⓒ) from the PBA-JOURNAL(B28) . (Page6-3) SAM4S ER-260 SERIES...
Page 27
4-1-7 Ass’y Keyboard 1. Separate the three harnesses( , , ⓜ ⓝ ⓚ) from the SWITCH-ROTARY(B30) & PBA MAIN(E17)(Page6-3) 2. Remove the four screws(B37) and Separate the ASS’Y KEYBOARD(B35 or B36) from the ASS’Y CASE UPPER (B). (Page6-3) SAM4S ER-260 SERIES...
Page 28
3. Separate the harness (ⓙ) and Remove the screw(E12). (page6-8) 4. Lift up the I/F PBA(E13).(page6-8) 4-2-2 Ass’y Trans Power 1. Separate the harnesses( , ⓟ ⓠ) and Remove the two screws(E14). (page6-8) 2. Lift up the TRANS-POWER (E15) from the CASE LOWER(E24).(page6-8) SAM4S ER-260 SERIES...
Page 29
4-3-2 Disassembly of the Window Rear Be sure to separate the ASS’Y CASE UPPER from the ASS’Y CASE LOWER. ① ② Pull the WINDOW REAR out as the Fig-2 carefully not to break the four ribs. Fig-2 SAM4S ER-260 SERIES...
Page 30
4-3-3 Disassembly of the Rear VFD PCB Be sure to separate the ASS’Y CASE UPPER from the ASS’Y CASE LOWER. ① pull out in the direction of the Fig-3 to separate the REAR VFD PCB from the ASS’Y CASE UPPER. ② Fig-3 SAM4S ER-260 SERIES...
Page 31
4. Disassembly and Assembly MEMO SAM4S ER-260 SERIES...
Page 32
3. Check the VPRT whether it is short or open. 4. Check the VPH whether it is short or open. 1. Check the KA34063(U30) Power VCC 2. Check the TR KSA1010(Q15) (+5V) Ok? 3. Check the VCC whether it is short or open. SAM4S ER-260 SERIES...
Page 33
3. Check the Decoder IC 74HC138 (U5). 4. Replace the SRAM. 1. Check the RTC_SCLK & SDA signal of RTC 2. Check the VBT(Battery Volt.). RTC Ok? 3. Check the RTC Clock 32.768KHz 4. Replace the RTC(PCF8563) SAM4S ER-260 SERIES...
Page 34
2. Check the regulator AME8807(U28) and related Circuit. 3. Check the LCD harness and soldering status. 1. Check the LCD EN, LCD RS Signal. LCD Diaplay 2. Check the buffer 74HCT574(U25) and related Circuit. 3. Check the LCD harness and soldering status. SAM4S ER-260 SERIES...
Page 35
(Clk / Data / Latch / Strobe#1/#2) 2. Check the VPH voltage. It is +6.0V 3. Check the VPH ON/OFF circuit and pattern. 4. Check the JOINT PCB and FFC harness. 5. Check and Replace the printer. SAM4S ER-260 SERIES...
Page 36
2. Check the Matrix Bus & Data Bus Failure? 3. Check the Diodes(BAT43WS *7EA) 4. Check the Key Board Assy 1. Check the Mode Key Assy Mode Key 2. Check the Diode (D11) 3. Check the 74HC138 & Data Bus SAM4S ER-260 SERIES...
Page 37
2. Check the Micro switch in the Drawer. Failure? Spool Motor Problem 1. Check the Spool Motor Signal CPU P1.3. Spool Motor 2. Check the VFD Display harness and Motor harness. 3. Check the related Circuit and pattern on Main B’D. SAM4S ER-260 SERIES...
Page 38
3. Check whether Signal is affected by the Cable Noise. 1. Check the connection of the H/W handshaking Line and Other side H/W Handshake 2. Check the I/F Cable whether it is open or short. 3. Confirm the H/W handshaking Protocol. SAM4S ER-260 SERIES...
5. Troubleshooting 5-7 Error Code Error Code Description Remark Input Error Printer Error (paper jam) Non Add # required Cash Declaration required Cash Drawer is open No Paper SAM4S ER-260 SERIES...
Page 40
6 Exploded Views and Parts List 6-1 Main Set [ Exploded View ] Figure6-1 Total Disassembly (ER-260) SAM4S ER-260 SERIES...
Page 41
6. Exploded Views and Parts List 6-1 Main Set A. ASS’Y COVER-PRINTER Figure 6-2. ASS’Y COVER-PRINTER 6.1. A. ASS’Y COVER-PRINTER Code No. Description/ Specification Q`ty Design-Location Serviceable Remark JK97-20056B MEA COVER-PRINTER:ER-260B JK72-20225B PMO-COVER PRINTER JK70-10320A IPR-CUTTER PAPER SAM4S ER-260 SERIES...
Page 42
6. Exploded Views and Parts List 6-1 Main Set B. ASS’Y CASE-UPPER Figure 6-3. ASS’Y CASE-UPPER SAM4S ER-260 SERIES...
ASS'Y HOUSING d. ASS'Y LOCK b. ASS'Y TRAY-TILL e. ASS'Y BOTTOM Figure 6-9. ASS’YDRAWER (5B/5C) a. ASS'Y BILL-COIN (7B8C) c. ASS'Y HOUSING d. ASS'Y LOCK b. ASS'Y TRAY-TILL e. ASS'Y BOTTOM Figure 6-10. ASS’YDRAWER (7B/8C) 6-12 SAM4S ER-260 SERIES...
Page 86
Use this page to record any special servicing information such as Service Bulletins or Supplements. When possible, record changes to Code numbers directly on the actual Parts List. Always record Service Bulletin numbers and Application Dates on this log to ensure that your data is always as current as possible. SAM4S ER-260 SERIES...
Page 87
Shin Heung Precision. September 2006 ⓒ Printed in KOREA V1.0 Code No. : JK68-70115A...