Page 2
This MotorGuide Electric Motor, assembled of U.S.A. and foreign components by MotorGuide, 835 W. 41st St., Tulsa, OK, USA, complies with requirements of Directives 89/392/EEC and 89/336/EEC, 92/31/EEC, and 93/68 EEC as amended. Dave Rowland MotorGuide Business Unit Manager MotorGuide 835 W.
For Repair Service ..........16 Raising and Lowering the Trolling Motor..7 Raising The Motor ........7 Replacement Parts & Ordering ......16 Lowering the Motor .........7 MotorGuide Accessories........16 Adjusting the Steering Tension (Hand Operated Models)........7 Warranty Information Adjusting the Motor Depth .........8 Trolling Motor Operation Two-Year Warranty ..........17...
MM5870. interference, cables should be routed separately from the trolling motor power cables. • Wire Size – For optimum performance, MotorGuide recommends the use of six (6) gauge (13 mm) wire if • IMPORTANT: Do not route the transducer cable...
12 Volt Battery Hook-up 36 Volt Battery Hook-up A) Battery A H) To foot pedal A) Black battery lead (-) D) Positive lead to main B) Battery B (DS models only) engine, bilge pumps, C) Battery C I) To optional sonar display B) Red battery lead (+) aerators, accessories D) Positive lead to main...
Quick Stow – Comes standard on some saltwater models only. A Quick Stow kit (MGA052B6) can be The trolling motor can now be placed in the mount. purchased from a MotorGuide Service Dealer. 90-MM6900...
Bow Mount Installation Rubber Isolator IF applicable, insert the rubber mounting isolators into 07 Standard bow mount the drilled holes. Position the wider side of the isolator toward the outside of the mount bracket. Tie Down Strap Heavy duty breakaway mount with springs Carefully select the area on the deck to install the mount.
BOW MOUNT OPERATION Raising the Motor Installing the Motor into the Mount Mount Rope Handle Bracket Door Knob Turn the bracket door knob to the left to loosen and Raise the motor out of the water by pulling on the mount open the bracket door.
Arrows trolling motor during rough water situations. The Tie-Down Strap is required to completely secure the motor. A Tie Down Strap can be ordered through a MotorGuide Service Dealer, part number # MGA029B6. CENTER REVERSE REVERSE...
Twist Tiller Speed Control Speed Control Five-Speed and Variable Speed Motors On /Off Toggle Switch & Decal ( Variable Speed Only) Variable Speed Twist Speed Control Knob Tiller Decal Foot operated motors are either five-speed or variable speed models. Control the speed of your motor by rolling the speed control knob with your hand or foot until you reach the desired speed.
DIGITAL STEERING TROLLING MOTORS Auto ON/OFF – Digital Steering units will turn ON when deployed to the run position and OFF when stowed. Press the Stow button to position the motor to land on the bracket channel. Pull the motor back into the boat and Features and Operation onto the bracket.
Steering the Motor Motor Set-Up Toe Down Heel Down Center Detent Stow Alignment Procedure Position Position Position Straight Ahead Right Turn Left Turn Rock the foot pedal heel down to steer left and toe down to steer right. The motor has a steering range of 400 Stow Button Stow Position Dial degrees to help you maneuver in tight spots.
To Activate a Single Momentary Button: Set the speed wheel at 0. Press and hold the Momentary button you want to activate. Press and release the Constant-On button three times. Release all buttons. To Activate Both Momentary Buttons: Press and hold both Momentary buttons. Press and release the Constant button three times.
Adjusting the Foot Pedal Resistance Foot Pedal Calibration The foot pedal was initially calibrated at the factory. Recalibrate your foot pedal if you: • Notice you are not getting a full 400-degree steering rotation. • Have installed a new pedal on your motor. •...
Check the tightness of the battery lead connections. Periodically inspect for loose or corroded wiring CAUTION connections. Thoroughly rinse your trolling motor with freshwater Make sure the motor is disconnected from the after each use in saltwater. battery before replacing the propeller.
TROUBLESHOOTING PROBLEM POSSIBLE CAUSES AND/OR SOLUTIONS Loss of power • The propeller may be fouled. Remove the propeller; clean or replace if necessary. • The battery connections may be corroded. • The battery may have low voltage. Recharge and test for a bad cell. •...
Singapore: 65-6546-6160 MOTORGUIDE ACCESSORIES Making It More Perfect. Who says you cannot make the best even better? MotorGuide® factory accessories let fishermen customize motors to their own unique needs. In addition, every one is a perfect fit. REPLACEMENT PROPS Prop...
MotorGuide, at its discretion, will repair or replace items covered required with the return of the product for warranty consideration.
Page 20
REGISTRATION IS INCLUDED IN THE BOX AND IS SEPARATE FROM THIS MANUAL. PLEASE FILL OUT AND MAIL IMMEDIATELY TO VALIDATE YOUR WARRANTY. Model Number Locations & Serial Number Locations Voltage Thank you for purchasing and registering this MotorGuide product. 90-MM6900...
MAINTENANCE LOG Use this log to record all maintenance performed on your trolling motor. Save all work orders and receipts. Date Maintenance Performed 90-MM6900...
Page 22
MotorGuide 835 W. 41 Street Tulsa, Oklahoma 74107 (920) 929-5040...
Need help?
Do you have a question about the Freshwater and is the answer not in the manual?
Questions and answers