Page 1
AIR CONDITIONER INSTALLATION AND USER MANUAL VERS. 001...
Page 2
Via E. Majorana , 49 48022 Lugo (RA) ITALY “CE” COMPLIANCE STATEMENT Under Machine Directive 89/392/EEC, attachment II A We hereby represent that the air conditioner, the data concerning which appear below, has been designed and built to correspond to the essential safety and health requirements laid down by the European Directive on Machine Safety.
CONTENTS 1 FOREWORD ........................pag. 4 Purpose and scope of this manual ................pag. 4 Symbols and Definitions .................... pag. 4 ................... General Information pag. 2 AIR CONDITIONER IDENTIFICATION DATA ..............pag. 5 Components ....................... pag. 5 Identification plate ......................pag. 5 Technical features .......................
1.3 General Information contents. The ICEBERG 3500 air conditioners have been The most important parts of the text are in bold designed for installation on the roofs of vehicles. letters and preceded by symbols described below.
2.2 Identification label Model AIR CONDITIONER IDENTIFICATION DATA Machine code Serial number Compressor and fans consumption 2.1 Components (fig. 1) Heater power Coolant gas type and quantity Ventilation grid Top hood Identification label Diffuser 3500R Adjustable air outlets ICEBERG Ambient air suction grid CODE : 00640 S.N.000303266 Fan speed selector switch...
3.2 Weight Installation must be performed Weight without packing. by qualified and properly trained personnel only. ICEBERG 3500 Kg 34 4.2 Installation 3.3 Handling Before starting to install, you The air conditioners, complete with their packag- must disconnect all the power supply of the...
In order to install the air conditioner, you must first Remove existing rooflight and sealants making sure make sure the roof of the vehicle is able to hold its roof surface is clean and even [Fig. 3 ref. 1] Seal weight.
4.2.3 Power supply cable To set up the power supply for the air conditioner, lay a three-pole (positive-neutral-earth), power sup- ply cable with a cross section of at least 2.5 mm This cable must be connected at one end to the differential cut-off switch previously placed inside the distribution board of the vehicle, while the other end must reach the opening on the roof.
4.3 Positioning the air conditioner Do not crush the foam sealing Before positioning the air conditioner on the roof of too much - it must be at least 10 mm thick the vehicle, spread a sufficient of quantity slow- [Fig. 9 ref. 3]. drying sealant around the edges of the opening.
4.4 Installing the diffuser After securing the air conditioner to the roof of the vehicle, connect the power supply cable to the con- nection terminal board [Fig. 10 ref. 3], located on the diffuser, complying with the positions shown on the adhesive label: blue wire: neutral brown wire: positive...
5.3 Air diffusion outlets USER INSTRUCTIONS The diffuser panel [Fig. 1 ref. 4] houses five cooled 5.1 Foreword or heated air diffusion outlets [Fig. 1 ref. 5]. Each outlet is provided with two mobile baffle plates which allow you to choke and direct the air jet [Fig. The Manufacturer shall not be 14].
First choose Maximum Cool and the second ven- tilation speed. When you have reached the temperature you want, choose the first ventilation speed, then turn the thermostat knob counter-clockwise until the compressor goes off (you can tell this has happened when the noise diminishes).
The walls of the vehicle are sufficiently insulated. 5.8 Turning off The doors are not opened too frequently. There are not too many people inside the vehicle. To turn the air conditioner off, position the switch The voltage is less than 230 V. [Fig.
MAINTENANCE DISPOSAL Accurate inside cleaning of the air conditioner is If you have to dispose of the air conditioner, refer important to keep it efficient. to a specialised workshop. Before accessing the air con- All the waste material must not ditioner, you must disconnect the 230V power be disposed of in the open, but in special con- supply and wait for all parts to cool off.
TROUBLESHOOTING (for technical staff only) Before performing the checks listed below, make sure that the ON/OFF switch is in the ON position [Fig. 15 ref. 4], the thermostat is in the all-cold position [Fig. 15 ref. 2], and the fan speed selector switch is in position 1 [Fig.
Page 16
2) PROBLEM The compressor does not work CHECK Make sure that there is 12 VDC between the black wire of the relay [Fig. 16 ref. 2] and the red wire of the fan speed selector [Fig. 16 ref. 8]. OPERATION Check the harness and the multi-wire connector [Fig. 16 ref. 7]. CHECK Make sure that there is 12 VDC on the fan speed selector [Fig.
Page 17
5) PROBLEM The fan of the evaporator does not work CHECK Make sure that there is 12 VDC between the green ventilation speed selector switch wire [Fig. 16 ref. 8] and the black relay selector wire [Fig. 16 ref. 2]. OPERATION Replace the fan speed selector switch.
The warranty shall be valid only if the customer is able to show a document evidencing the date of purchase (invoice or receipt). This document must be kept whole and must be submitted to the Telair after-sales centre when asking for operation under warranty.