Honeywell Lynx Plus Programming Manual page 8

Data Field Display
72 72 72 72
BYPASS RES BYPASS BYPASS BYPASS RES RES RES REP REP REP REP
73 73 73 73
AC AC AC AC RESTORE RESTORE RESTORE REP RESTORE REP REP REP
74 74 74 74
LO LO LO LO BAT BAT RES BAT BAT RES REP RES RES REP REP REP
75 75 75 75
RF RF RF RF LOBAT LOBAT RES RES REP REP
LOBAT LOBAT RES RES REP REP
76 76 76 76
TEST TEST RES RES REPORT REPORT
TEST TEST RES RES REPORT REPORT
DYNAMIC SIGNALING FIELD (✻77)
77 77 77 77
DYNAMIC DYNAMIC SIG DYNAMIC DYNAMIC SIG OPTS SIG SIG OPTS OPTS OPTS
78 78 78 78
PROG TONE GEN TM PROG TONE GEN TM PROG TONE GEN TM PROG TONE GEN TM
OUTPUT AND SYSTEM SETUP (✻80, ✻81, ✻83–✻85) See Procedures later in this manual.
86 86 86 86
MULTI MULTI- - - - MODE MULTI MULTI MODE MODE MODE EMAIL EMAIL EMAIL EMAIL
87 87 87 87
AUX AUX AUX AUX FUNC FUNC 1BTN FUNC FUNC 1BTN PG PG PG PG 1BTN 1BTN
8 8 8 8 8 8 8 8
P P P P A A A A G G G G ER CHARACTERS ER CHARACTERS ER CHARACTERS ER CHARACTERS
Function& Programming Options [ ] = Programmed Table 1 Default Values
Bypass Restore Report Code
| [0,0]
AC Restore Report Code
| [0,0]
Low Bat Restore Report Code
| [1,0]
RF Transmitter Low Battery Restore Report Code
| [1,0]
Test Restore Report Code
| [0,0]
Dynamic Signaling Options
| [0, 0]
1st Entry (delay before switch CS reporting path)
0 = Redundant
reporting on dialer
and LRR/IP device
1 = 15 seconds
2 = 30 seconds
2nd Entry
0 = Primary Dialer
Preferred Channel
Programmable Tone Generation Time
| [0, 0]
00 = Disabled; 01-09 = 100-900 ms; 10-99 = 1.0 – 9.9 secs
Multi-Mode (E-Mail Notification)
[0]
0 = Disable multi-mode devices; 1 = Enable multi-mode device address #6 only;
2 = Enable multi-mode device address #7 only; 3 = Enable multi-mode addresses
Aux Function/ 1-Button Paging
[0]
0 = Aux key performs defined function (macro);
1 = Aux key sends message to pager or voice message to follow me system phone
number.
If 1, you must also select an option 6-9 in field ✻49 for the pager or 10-13 for the follow me
system announcement.
Pager Characters
Up to 16 digits can be entered that will appear in front of the 7-digit pager message sent by
the control. Refer to the Installation Instructions (fields ✻87, ✻88 and ✻49) for full
descriptions of the paging feature. You do not need to fill all 16 digits (press [✻] to
advance to next field).
To clear entries, enter ✻88✻. To enter "✻" = [#] + [11]; To enter "#" = [#] + 12]; To
enter 2-second pause = [#] + [13] (some pagers require an additional delay [pause] in
order to receive the entire message)
3 = 45 seconds 8 = 120 seconds
4 = 60 seconds 9 = 135 seconds #10
5 = 75 seconds = 150 seconds
6 = 90 seconds #11 = 165 seconds
7 = 105 seconds #12 = 180 seconds
1 = LRR/IP 2 = LRR/IP
Preferred Channel reporting only
- 8 -
#13 = 195 seconds
#14 = 210 seconds
#15 = 225 seconds