Installing The Rf Receiver; Installing A 5800Tm Module; Installing The Transmitters - Honeywell Ademco Vista-48LA Installation And Setup Manual

Installing the RF Receiver

Use one of the following receivers:
RF Receiver Number of Zones
5881ENL up to 8 (including keyfob buttons)
5881ENM up to 16 (including keyfob buttons)
5881ENH/5881EH up to 40 plus 16 keyfob buttons
5882EU/
5882EUH/5883
1. Set Device Address to "00" as described in its
instructions (set all switches to the right, "off" position).
2. Mount the receiver, noting that the RF receiver can
detect signals from transmitters within a nominal
range of 67m.
3. Connect the receiver's wire harness to the control's
keypad terminals. Plug the connector at the other end
of the harness into the receiver. Refer to the
installation instructions provided with the receiver
for further installation procedures regarding antenna
mounting, etc.
NOTE ANTENNAS
(INSERT IN
CIRCUIT BOARD IS MOUNTED IN
RIGHT-HAND
CONTROL'S CABINET. GROUNDING
TERMINALS)
LUGS (2) PROVIDED MUST BE INSERTED
IN LEFT-HAND TERMINALS OF ANTENNA
INSERT IN
BLOCKS AND SECURED TO CABINET. RIGHT- HAND
(SEE RECEIVER'S AND CONTROL'S TERMINALS
INSTRUCTIONS)
MODEL NO. IS INDICATED ON CIRCUIT BOARD
5882
LOCATION
MOUNTING
HOLES
INTERFERENCE
INDICATOR
LED
CIRCUIT BOARD
TO RELEASE CIRCUIT BOARD,
REMOVE SCREWS AND
BEND BACK TABS
Figure 9. 5881EN RF Receiver (cover removed)

Installing a 5800TM Module

1. Mount the 5800TM next to the RF receiver (between
one and two feet from the receiver's antennas) using
its accompanying mounting bracket. Do not install
within the control cabinet.
2. Connect the 5800TM to the control panel's keypad
connection terminals as shown on the Summary of
Connections diagram and set to address 28.

Installing the Transmitters

1. To be sure reception of the transmitter's signal at the
proposed mounting location is adequate, perform a
Go/No Go Test (see the Testing the System section).
2. Install transmitters in accordance with the
instructions provided with each.
3. Set 5827, 5827BD, 5804BD wireless keypads to the
programmed House ID (field *24), using its DIP
switches (5827) or follow the instructions provided
with the device.
YELLOW
TO CONTROL'S
RED
REMOTE KEYPAD
BLACK
CONNECTION
GREEN
POINTS.
DIP
SWITCH
WIRING OPENING
KNOCKOUT AREA
FOR SURFACE WIRING
SOCKET PLUG
5881-003-V0
Mounting and Wiring the Control
Notes
• The receiver is supervised and a trouble report is
sent ("CHECK 100" displayed) if communication
between the panel and receiver is interrupted, or
if no valid RF signals from at least one supervised
transmitter are received within 12 hours.
• Only one receiver can be installed in a system.
If the receiver is mounted remotely:
• Place the RF receiver in a high, centrally located
area for best reception.
• Do not locate the receiver or transmitters on or
near metal objects. This will decrease range
and/or block transmissions.
• Do not locate the RF receiver in an area of high
RF interference (indicated by frequent or
prolonged lighting of the LED in the receiver;
random flicker is OK).
• Do not locate RF receiver closer than 3m from
any keypads to avoid interference from the
microprocessors in those units.
WIRELESS ZONE NUMBERS
transmitter zones 9-48
button or transmitter zones 49-64
Notes
• Use this module only in 345Hz RF systems and if
you are using one or more wireless bi-directional
keypads or keyfob; 5800TM is not necessary if
using a Transceiver (e.g., 5883).
• The 5800TM must be set to address 28 (cut red-
W1 jumper).
• The 5800TM can be used in partition 1 only.
• For additional information regarding the
5800TM, refer to the 5800TM's instructions.
Notes
• Refer to the table of compatible devices at the
back of this manual.
• Supervised transmitters
the receiver at 70-90 minute intervals. If at least
one check-in message is not received from each
transmitter within a 12-hour period, the "missing"
transmitter number(s) and "CHECK" is displayed.
†
Hand-held transmitters (e.g., 5802, 5802CP, 5804,
5804BD, 5827, 5827BD) do not send check-in signals.
†
send check-in signals to
2-9