Data Field Programming; About Data Field Programming; Programming Data Fields; System Setup Fields - Honeywell Ademco Vista-48LA Installation And Setup Manual

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

About Data Field Programming

The following pages list this control's data fields in numerical order. Field numbers are listed in the
left column followed by a "Title and Data Entries" column, which lists the valid entries for each field.
Experienced installers can simply follow this column when programming the data fields. The
"Explanation" column provides explanatory information and special notes where applicable.

Programming Data Fields

Data field programming involves making the appropriate entries for each of the data fields.
Start Data Field programming by entering the installer code + 8 + 0 + 0.

System Setup Fields

FIELD TITLE and DATA ENTRIES
Installer Code
*20
Enter 4 digits, 0-9
Quick Arm Enable
*21
0 = do not allow quick arm
1 = allow quick arm
RF Options
*22
Entry 1 - Jam detection
0 = no RF Jam detection; 1 = detect RF Jam*
Entry 2 – supervision interval
0 = 12 hours; 1 = 2 hours; 2 = 20 minutes
when disarmed/ 2 hours when armed
3 = 12 hrs for burg zones/ 3 hrs for fire zones
Quick (Forced) Bypass
*23
0 = no quick bypass
1 = allow quick bypass (code + [6] + [#] )
RF House ID Code
*24
00 = disable all wireless keypad usage
01–31 = House ID for partition 1, 2, 3
Arming Prevention Override
*25
Entry 1: 0 = no arming prevention override
1 = allow arming with an RF trouble failure
2 = allow arming with an AC Mains Loss
4 = allow arming with a system low battery
Entry 2: 0 = no tamper override***
†
1 = allow arming with a tamper fault
†
2 = allow arming with a tamper fault once
Chime By Zone
*26
0 = no zone list (chimes on fault of any entry/
exit or perimeter zone when chime mode on)
1 = use zone list (chimes on fault of specific
zones in zone list 3 when Chime mode on)

Data Field Programming

EXPLANATION
The Installer Code is used to assign the 4-digit Master Security Code.
See "Master Code" in the System Operation section for procedure.
If enabled, a user code is not needed to arm the system. Instead,
users can press the [#] followed by an arming key to arm the system.
However, the user code is always needed to disarm the system.
If jam detection enabled, a report is sent if the system detects an RF
jamming signal. See field *178 for other jam/supervision options.
When using RF Receivers with 5800 series transmitters, entry 2
should be 0 or 3.
All zones bypassed by this function will be displayed after the bypass
is initiated.
The House ID identifies receivers and wireless keypads. If a 5827 or
5827BD wireless keypad or 5804BD/5804BDV transmitter is being
used, a House ID code must be entered, and the keypad must be set
to the same House ID. You can assign RF house ID for each partition.
Does not apply to 5839 or 5828/5828V.
If no override is selected, systems will not be able to be armed when
there is a supervision failure, system low battery, AC mains loss, or a
tamper condition.
If override is enabled, the user must enter the arming sequence twice
to arm the system; the first entry of user code + arm command will
not arm, but a second entry of user code +arm command will arm the
system.
E.g., To select arm with "supervision failure" and "low battery", enter
5 (1 + 4)
† NOTE: If tamper option 1 or 2 is selected, field *175 digit 2 must
be "0."
Chime by Zone
If enabled, you can define the specific zones intended to chime when
faulted while the system is in Chime mode. Use zone list 3 to assign
these zones (see ∗81 Zone List Programming section for details).
S E C T I O N
4-1
4