Table of Contents
Advertisement
Filename [M150SEK_07Timer Recording.fm]
M150SEK_00.book Page 38 Wednesday, June 15, 2005 4:04 PM
TIMER RECORDING
38
EN
Manual Timer Programming
You can programme this unit to timer record as many as
8 programmes up to 30 days in advance. To perform normal timer
programming without using EPG, use the following procedure to
set your unit to timer record the programme.
ATTENTION:
If timer programming cannot be set or cancelled, wait for about
40 seconds and then try again.
●
Turn on the unit.
●
Turn on the TV and select an input mode such as EXT1.
●
Make sure that the unit's built-in clock is set properly.
●
Slide the TV/DVD switch to DVD.
AUX
1
Load a recordable disc.
●
For details, refer to APlacing A DiscB (A pg. 9).
2
Press PROG to display
PROGRAMME CHECK
the APROGRAMME
DATE
CHECKB screen.
05/07 SAT
●
When 8 timer
10/07 THU
11/07 FRI
programmes appear on
11/07 FRI
++++++++++++++++++ NEW TIMER PROGRAMME ++++++++++++++++++
the TV screen, you need
to cancel some of the
reserved programmes.
EXIT
PROG
3
Press selection keys
TIMER PROGRAMME
repeatedly to select
ANEW TIMER
PROGRAMMEB, then
press ENTER.
05/07 SAT
4
Press selection keys to
DAILY/WEEKLY
set the desired date
(ADATEB), then press E.
5
EXIT
Press selection keys to
set the desired start
PROG
time (ASTARTB), then press E.
●
Each press of F G increases/decreases the start time in
1 minute interval.
●
To increase/decrease the start time in 30 minutes interval,
press and hold F G.
TV
DVD
TIMER j
PROG
Selection Keys
(FGDE)
ENTER
START
STOP
TV PROG
DAILY/WEEKLY
REC MODE
19:00 - 20:00
BBCi 51
WEEKLY
SP
22:00 - 22:30
BBC 40
XP
CBBC 30
13:30 - 14:00
LP
BBC 1
16:00 - 17:00
LP
DISC TIMER PRGM
OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
DATE
START
STOP
TV PROG
20:00
20:30
VTM 10
REC MODE
NAME
LP
CONFIRM
SET TIMER PROGRAMMING WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
Masterpage:Left+
6
Press selection keys to set the desired stop time (ASTOPB),
then press E.
●
Each press of F G increases/decreases the stop time in
1 minute interval.
●
To increase/decrease the stop time in 30 minutes interval, press
and hold F G.
7
Press selection keys to set the desired channel (ATV PROGB),
then press E.
8
Set the other recording options as required.
9
Press ENTER to access the Programme Confirmation screen.
10
Press ENTER to complete the timer programming.
●
To programme another timer, repeat steps 2 - 10.
11
Press TIMERj to engage the unit's timer mode.
The unit turns off automatically and j appears on the front
●
display panel.
●
To disengage the timer mode, press TIMERj again.
NOTES:
●
When two successive programmes are recorded with the
AManual Timer ProgrammingB function, the ending of the first
programme or the beginning of the second programme may not
be recorded.
●
If the copy limited programme is received during timer recording,
the unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you
programmed.
Satellite Receiver Users
To record a satellite broadcast using Manual Timer
Programming:
A Perform Manual Timer Programming.
●
In step 7, press AUX to set ATV PROGB to ASATB. Then press
F G to enter the channel position for the satellite broadcast.
B Set the satellite receiver to the appropriate channel for
recording.
●
Leave the satellite receiver's power on.
Advertisement
Table of Contents
