Table of Contents
Advertisement
Filename [M150SEK_05Name.fm]
M150SEK_00.book Page 16 Wednesday, June 15, 2005 4:04 PM
INSTALLING YOUR NEW UNIT
16
EN
Basic Connection
To [ANTENNA IN]
Back of unit
To [L-1 IN/OUT]
To
[ANTENNA
To
OUT]
[COMPONENT
VIDEO OUT
(Y/P
/P
)]
B
R
Component
video cable
(not supplied)
RF cable
(supplied)
To 75 ohm terminal
It's essential that your unit be properly connected.
ATTENTION:
●
Your TV must have a 21-pin AV input connector (SCART) for
the basic connection to the unit.
●
Connect the AC plug only after all connections to the TV has
been completed.
TV aerial cable
Mains outlet
Mains power cord
To [AUDIO
OUT]
21-pin SCART
Audio cable
Cable
(not supplied)
(supplied)
TV
Masterpage:Left0
THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO
OPERATION CAN BE PERFORMED.
1
Place the unit on a stable, horizontal surface.
2
Connect the unit to a TV depending on the TV and cables you
use.
8 Basic Connection
To connect to a TV with 21-pin SCART input connector ^
A Disconnect the TV aerial cable from the TV.
B Connect the TV aerial cable to the [ANTENNA IN] connector on
the rear panel of the unit.
C Connect the [ANTENNA OUT] connector on the rear panel of
the unit and the TV's aerial connector with the supplied RF
cable.
D Connect the [L-1 IN/OUT] connector on the rear panel of the
unit and the TV's 21-pin SCART connector with a supplied 21-
pin SCART cable.
●
The [L-1 IN/OUT] connector accepts and delivers either a
composite signal (regular video signal), Y/C signal or RGB
signal.
●
Set your TV to the VIDEO, Y/C, or RGB mode according to the
type of your TV's SCART connector.
8 Component Video Connection
To connect to TV's component video input connectors ^
A Perform steps A - C of ABasic ConnectionB.
B Connect the unit's [COMPONENT VIDEO OUT (Y/P
connectors to the TV's component video input connectors.
C Connect the unit's [AUDIO OUT] connectors to the TV's AUDIO
input connectors.
●
You can obtain high-quality component video pictures.
●
If your TV is not stereo-capable, use the unit's [AUDIO OUT]
connectors to connect to an audio amplifier for Hi-Fi stereo
sound reproduction.
●
By using the component video connection, you can view the
images in the progressive mode. For switching to the
progressive mode, refer to AScan Mode SetB (A pg. 63).
NOTE:
Select an appropriate option of AL-1 OUTPUTB as follows
(A pg. 57):
When your TV's SCART
connector accepts:
Composite signals
Y/C signal (separated
luminance (brightness) and
chrominance (colour) signals)
RGB signal
Component video signal
●
When the setting selected is not in accordance with the TV
connected and depending on the type of appliance connected
to the unit, the correct picture will not appear.
●
This unit only supports 625i/625p PAL signals. Other modes are
not receivable.
3
Plug the end of the mains power cord into a mains outlet.
●
APLEASEB and AWAITB blink alternately on the front display
panel when the AC plug of the mains power cord is connected
into a mains outlet. And it takes approximately 30 seconds for
the unit to be turned on. This is not a malfunction.
If you possess a satellite receiver, refer to AConnecting To A
Satellite ReceiverB as well. (A pg. 59)
/P
)]
B
R
Set AL-1 OUTPUTB to:
ASCART VIDEOB
ASCART S-VIDEOB
ASCART RGBB
ACOMPONENTB
Advertisement
Table of Contents
