Table of Contents
Advertisement
Manual Timer Programming
You can programme this unit to timer record as many as
16 programmes.
If you do not know the PlusCode number for the programme you
wish to record, use the following procedure to set your unit to timer
record the programme.
●
Make sure that the unit's built-in clock is set properly.
●
Turn on the unit.
●
Turn on the TV and select the AV mode.
●
Slide the TV/CABLE/SAT/DVD switch to DVD.
AUX
ENTER
1
Load a recordable disc if recording to DVD.
2
Press PROGRAMME to access the programme top screen.
3
Press selection keys to select ACALENDAR PR.B, then press
ENTER.
●
When APROGRAMME FULL DELETE UNWANTED TIMER
PROGRAMMESB appears on the TV screen, you need to
cancel some of the reserved programmes. (A pg. 50)
4
Press selection keys to select the desired date, then press
ENTER.
5
Press selection keys
to select ARECORD
TOB, then press
ENTER. Press
selection keys to
select the desired
recording deck, then
press ENTER.
6
Press selection keys
to select ASTARTB,
then press ENTER.
Press selection keys to set the desired start time, then press
ENTER.
Each press of F G increases/decreases the start time in
●
1 minute interval.
●
To increase/decrease the start time in 30 minutes interval,
press and hold F G.
7
Press selection keys to select ASTOPB, then press ENTER.
Press selection keys to set the desired stop time, then press
ENTER.
●
Each press of F G increases/decreases the stop time in
1 minute interval.
●
To increase/decrease the stop time in 30 minutes interval,
press and hold F G.
CABLE/SAT
TV
DVD
PROGRAMME
Selection Keys
FGDE
2
PROGRAMME > CALENDAR PR. (2/3)
14/01/04 WED 22:30 - 23:00
SELECT WITH @
HDD
RECORD TO
THEN PRESS [ENTER]
22:30
START
23:00
PRESS [PROGRAMME]
STOP
TO EXIT
BBC1
TV PROG
[0]: SAT
PROGRAMME
ENTER
CONFIRM
EXIT
SELECT
8
Press selection keys to select ATV PROGB, then press
ENTER. Press selection keys to select the desired channel.
9
Press selection keys to select ACONFIRMB, then press
ENTER.
10
Set the other recording options as required.
●
Refer to step 8 in AVIDEO Plus+
(A pg. 47).
11
Press selection keys
to select AOKB, then
press ENTER to
access the
Programme
Confirmation screen.
12
Press selection keys
to select AEXITB, then
press ENTER to
complete timer
programming.
●
To programme another timer, press selection keys to select
ACONTINUEB, then press ENTER.
●
If APROGRAMME OVERLAPPEDB appears on the TV screen,
delete or modify the programmes.
NOTES:
●
When two successive programmes are recorded on a DVD-RW
disc with Manual Timer Programming function, the beginning of
the second one may be left off the recording.
●
If the copy limited programme is received during timer recording,
the unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you
programmed.
Satellite Receiver Users
To timer record a satellite broadcast using Manual Timer
Programming:
A Perform ASatellite Receiver Control SettingB (A pg. 24).
B Perform AManual Timer ProgrammingB (A pg. 49).
In step 8, press AUX to change ATV PROGB to ASATB. Then
press selection keys to enter the channel position for the
satellite broadcast.
C Leave the satellite receiver's power on.
Relief Recording
When a programme that is set for the DVD deck cannot be
recorded properly, the programme is recorded to the HDD deck
instead in XP mode.
●
If the remaining capacity of the hard disc is not sufficient, the
programme is recorded to the DVD deck until the remaining
BBC1
[MISC. ] XP
capacity of the DVD disc lasts.
●
If AJUSTB is selected for the recording mode, the current
recording mode for the DVD deck is applied.
TIMER RECORDING
®
Timer ProgrammingB
2
PROGRAMME > CALENDAR PR. (3/3)
14/01/04 WED 22:30 - 23:00
GARDENING
[EDUCATION] FR360
1:00
SELECT WITH @
INPUT TITLE
GARDENING
THEN PRESS [ENTER]
EDUCATION
CATEGORY
PRESS [PROGRAMME]
VPS/PDC
TO EXIT
WEEKLY/DAILY
MON-FRI (FOR A WEEK)
REC MODE
FR360
PROGRAMME
ENTER
OK
EXIT
SELECT
49
EN
BBC1
28:00
OFF
Advertisement
Table of Contents
