On-Disc Timer Programming - JVC DR-M150SEK Instructions Manual

Filename [M150SEK_07Timer Recording.fm]
M150SEK_00.book Page 39 Wednesday, June 15, 2005 4:04 PM

On-Disc Timer Programming

On-Disc Timer Programming is a function used with discs that are
especially intended for a specific programme. The disc is then
programmed for a programme you always watch every day or
every week. Since older programmes are automatically
overwritten, a single disc can be used without worrying about how
much recording capacity remains. You can programme each disc
to timer record as many as 8 programmes up to 30 days in
advance.
●
Make sure that the unit's built-in clock is set properly.
●
Turn on the TV and select an input mode such as EXT1.
●
Load a DVD-RAM or DVD-RW (VR mode) disc for
programming.
●
Slide the TV/DVD switch to DVD.
ATTENTION:
●
On-Disc Timer Programming is possible only with the disc for
On-Disc Timer Programming.
●
If data is recorded on a disc for On-Disc Timer Programming
using a unit from another manufacturer, On-Disc Timer
Programming may not function properly.
●
If timer programming cannot be set or cancelled, wait for about
40 seconds and then try again.
AUX
PROG
To Make The Disc For On-Disc Timer Programming
1
2
●
●
3
4
●
●
5
TV DVD
●
DVD A
●
6
7
●
Selection Keys
8
(FGDE)
ENTER
●
●
9
10
11
Satellite Receiver Users
To timer record a satellite broadcast using On-Disc Timer
Programming:
A Perform On-Disc Timer Programming.
B Set the satellite receiver to the appropriate channel for
Masterpage:Right+
Press PROG to access
the Programme Check PROGRAMME CHECK
screen.
DATE
++++++++++++++++++ NEW TIMER PROGRAMME ++++++++++++++++++
Press selection keys to
select ADISC TIMER
PRGMB, then press
ENTER.
When some
programmes are
EXIT
recorded on the disc, a
PROG
caution message
appears. You can either format the disc (A pg. 67) or insert a
new disc, then re-perform the procedure from step 1.
When On-Disc Timer Programming has already been made on
the disc, press selection keys to select ANEW TIMER
PROGRAMMEB, then press ENTER.
Press selection keys to
DISC TIMER PRGM
set the desired date
(ADATEB), then press E.
Press selection keys to
DATE
05/07 SAT
set the desired start time
(ASTARTB), then press E.
DAILY/WEEKLY
Each press of F G
WEEKLY
increases/decreases the
start time in 1 minute
EXIT
interval.
PROG
To increase/decrease the
start time in 30 minutes interval, press and hold F G.
Press selection keys to set the desired stop time (ASTOPB),
then press E.
Each press of F G increases/decreases the stop time in
1 minute interval.
To increase/decrease the stop time in 30 minutes interval, press
and hold F G.
Press selection keys to set the desired channel (ATV PROGB),
then press E.
Press selection keys to set ADAILY/WEEKLYB, then press E.
For details on ADAILY/WEEKLYB setting, refer to ADaily/Weekly
Recording FunctionB (A pg. 37).
Set the other recording
DISC TIMER PRGM
options as required.
ARecording ModeB
(A pg. 34)
DATE
AModify Title NameB
05/07 SAT
(A pg. 46)
DAILY/WEEKLY
Press ENTER to access
WEEKLY
the Programme
Confirmation screen.
EXIT
Press ENTER to PROG
complete ATo Make The Disc For On-Disc Timer
ProgrammingB.
●
To programme another timer using ATo Make The Disc For On-
Disc Timer ProgrammingB, repeat steps 1 - 10.
Press DVD A to turn off the power.
●
is displayed on the front display panel.
To disengage the timer mode, press DVD A again.
●
●
In step 6, press AUX to set ATV PROGB to ASATB. Then press
F G to enter the channel position for the satellite broadcast.
recording.
●
Leave the satellite receiver's power on.
TIMER RECORDING
39
EN
START STOP TV PROG DAILY/WEEKLY REC MODE
DISC TIMER PRGM
OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
START STOP TV PROG
REC MODE
NAME
LP
CONFIRM
SET TIMER PROGRAMMING WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
START STOP TV PROG
18:30 20:30 YORN 1
REC MODE
NAME
LP
CONFIRM
SET TIMER PROGRAMMING WITH [CURSORS]
THEN PRESS [ENTER]
SELECT