Page 2
Approved Copy TABLE OF CONTENTS INTRODUCTION SETTING UP YOUR STASIS™ FLEX START WITH STAND ALONE STASIS™ FLEX TO USE STASIS FLEX® WITH GOLD MOUNT ® TO MOUNT GOLD MOUNT ADAPTER PLATE TO STASIS™ FLEX ® TO USE STASIS™ FLEX WITH ELIPZ BATTERY SYSTEM ® TO BACK MOUNT ELIPZ ON STASIS™ FLEX ® 2-3 OPERATING STASIS™ FLEX PRECAUTIONS LIMITED WARRANTY...
Page 3
Approved Copy TO USE STASIS FLEX WITH INTRODUCTION GOLD MOUNT The Anton/Bauer Stasis Flex is a versatile handheld support assist device ™ that can be used alone or as a power support with Anton/Bauer Gold Mount or ElipZ batteries. The unique patent pending locking Flex arm ® ® Requires one of the adapter plates below (see catalog for information): allows a camera to be instantly adjusted to a variety of shooting positions and locked in place at the touch of a lever. FGM-S Gold Mount • ®...
Page 4
USING STASIS FLEX W/ ElipZ BATTERY SYSTEM Approved Copy REQUIRES: • ElipZ extension cable – Extends standard ElipZ camera cable for back mounting of ElipZ – powers camera and ElightZ with native 7.2V. ® ® ® • Connector support (included with extension cable) (Figure C) • Spare ElipZ mounting shoe (optional) ® TO BACK MOUNT ElipZ ON STASIS FLEX OPERATING STASIS FLEX 1. Attach ElipZ...
Page 5
OPERATING STASIS FLEX (CONTINUED) Approved Copy Adjusting the position of the camera: WHILE SUPPORTING positioning link (Figure 4) a few degrees from the “12 o’clock” position CAMERA, (As in picture on page 1) open locking lever (Figure 5). The or with two (2) marks in alignment. Simply open the locking lever flexible arm will release completely when latch is open. IT IS BEST...
Page 6
PRECAUTIONS Approved Copy READ AND FOLLOW ALL INSTRUCTIONS FOR THIS DEVICE AND ANY DEVICE WITH WHICH IT WILL BE USED. ALWAYS HOLD CAMERA SECURELY WHEN RELEASING OR LOCKING ARM LATCH. • • Be sure that the flex arm locking mechanism is securely latched. CAUTION: inadvertent operation of the latching mechanism of the Flex could result in the sudden release of support of the camera weight and this could result in the dropping of the camera.
1. MAIL WARRANTY REGISTRATION CARD or with any battery, charger or accessory not manufactured, produced or 2. REGISTER ON LINE AT www.antonbauer.com sold by Anton/Bauer. Anton/Bauer only authorizes the use of original Anton/Bauer products with this Product. Use only original Anton/Bauer The liability of Anton/Bauer hereunder is expressly limited to a claim for equipment with this Product. repair or replacement of the Product or as otherwise stated herein at Anton/Bauer’s sole discretion. Notice of any claim under this warranty shall be delivered to Anton/Bauer during the period of the warranty and the Product shall be returned with its packaging promptly, at your expense, to an Anton/Bauer Customer Support Center or to the address above. Upon receipt of the Product and a record of your compliance with the conditions of this warranty, Anton/Bauer will repair or replace the Product and return it to you, or issue a credit, as applicable. You are responsible for all shipping and handling charges to and from authorized facility. THIS WARRANTY DOES NOT APPLY TO AND IS VOID IN THE CASE OF...
Page 8
Approved Copy The following are trademarks of Anton/Bauer, Inc.: Anton/Bauer, Anton/Bauer logo and parallelogram design, Aspekt, Automatique, DataTap, DIONIC, Elipz, Egripz, Elightz, Essentialz, Gold Mount, HubZ, HyTRON, Impac, Interactive and design, LifeSaver, Logic Series, Logic Series Logo, Maxx man logo design, Nexus, PowerStrap, Proformer, Probe, ProPac, RealTime, Satellight, Snap-On, Stasis, Stasis Flex, Tandem, TrimPac, Ultrakit, Ultralight, “One World.
Need help?
Do you have a question about the STASIS FLEX and is the answer not in the manual?
Questions and answers