Anton/Bauer TITAN 70 Owner's Manual
Anton/bauer charger/power supply owner's manual
Hide thumbs
Also See for TITAN 70:
- Owner's manual (24 pages) ,
- User manual (24 pages) ,
- Operating instructions (3 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Anton/Bauer TITAN 70
Summary of Contents for Anton/Bauer TITAN 70
- Page 1 ® ™ TITAN Charger / Power Supply OWNER’S MANUAL...
-
Page 2: Table Of Contents
INTRODUCTION ... 1 FEATURES ... 1 SAFEGUARDS ... 2 GROUNDING/EARTHING Charging ... 3 Applications ... 3 Three Stage Charging Methodology ... 4 LED Indications... 5 OPERATION AS DC CAMERA SUPPLY FROM MAINS POWER LOSS ... 6 FCC NOTICE ... 7 SPECIFICATIONS ... -
Page 3: Introduction
- Lightweight (16 oz.) WARNING Titan 70 is a 70 watt power supply. Exceeding 70 watts may cause fuse to short leaving unit unable to function. Please check equipment to be powered to ensure under 70 watts of total draw. -
Page 4: Safeguards
Power Sources: Risk of Electrical Shock: Refer servicing to qualified service personnel. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. IMPORTANT WARNING: THIS APPARATUS MUST BE EARTHED. To ensure safe operation, the three pin plug supplied must be inserted only into a standard three-pin power point which is effectively grounded through the normal household wiring. -
Page 5: Charging
Charging As with all Anton/Bauer chargers, charging with TITAN 70 is fully automatic. Mount any Logic Series battery to the TITAN 70 and it will automatically determine and execute the appropriate charge routine. Applications The Titan 70 will charge any Anton/Bauer Logic Series Gold Mount ®... -
Page 6: Three Stage Charging Methodology
Three Stage Charging Methodology In general, the TITAN 70 will deliver a three stage charge routine to each battery. 1. Stage One will deliver a high rate charge matched to the capabilities of the battery (typically a one or two hour rate, depending on battery type). During this... -
Page 7: Led Indications
LED indicates three states; 1) solid green LED indicates Titan 70 is operating as a charger. 2) Flashing status green LED indicates Titan 70 is operating as a power supply. 3) No green LED indicates power has been removed from Titan 70. -
Page 8: Operation As Dc Camera Supply From Mains
TITAN 70 will again resume battery charging. If AC line voltage is removed from the TITAN 70, and a charged battery is mounted on the unit, power from the battery will be routed to the camera. When AC line voltage is restored, the battery will be re-evaluated for a proper charge routine. -
Page 9: Fcc Notice
Input Voltage Output Voltage Fuse Rating Maximum Power FUSE/TYPE REPLACEMENT The fuse of the TITAN 70 is a PCB mounted device which should only be replaced by a qualified service technician. FCC NOTICE SPECIFICATIONS 5.2” x 4.03” x 2.19” 16oz (1 lb.) 90-250VAC 50/60 Hz 16.4 VDC... -
Page 10: Warranty
LIMITED WARRANTY This one (1) year limited warranty for the product specified in this document is given by Anton/Bauer, Inc. (“Anton/Bauer”), 14 Progress Drive, Shelton, Connecticut 06484. If you have any questions regarding product applications, product specification, or to obtain warranty service on this or any Anton/Bauer product, contact the Anton/Bauer Customer Support Group or the company at the address above. - Page 11 The power behind the best cameras capturing the best images in the world. The following are trademarks of Anton/Bauer, Inc.: ACS, ADM, Anton/Bauer, Anton/Bauer logo and parallelogram design, Aspekt, Automatique, DataTap, Dionic, ElipZ, ElightZ, EgripZ, Gold Mount, HyTRON, Impac, InterActive and design, LifeSaver, Logic Series, Logic Series logo, Maxx man logo design, MicroCode, PowerStrap, Probe, Proformer, ProPac, RealTime, SSP, Satellight, Snap-On, Stasis, Tandem, TrimPac, Ultrakit, Ultralight, “The power behind the...
Need help?
Do you have a question about the TITAN 70 and is the answer not in the manual?
Questions and answers