Fujitsu ESPRIMO E Operating Manual
  1. Manuals
  2. Brands
  3. Fujitsu Manuals
  4. Desktop
  5. ESPRIMO E
  6. Operating manual

Fujitsu ESPRIMO E Operating Manual

Desktop pc
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ESPRIMO E
Operating Manual

Advertisement

Table of Contents
loading

Related Manuals for Fujitsu ESPRIMO E

Summary of Contents for Fujitsu ESPRIMO E

  • Page 1 ESPRIMO E Operating Manual...
  • Page 2 ... any technical problems or other questions which you would like to be clarified? Please contact: ● our Hotline/Help Desk (see the included Help Desk list or go to: http://ts.fujitsu.com/support/helpdesk.html) ● your sales partner ● your sales outlet Further information can be found in the "Safety", "Ergonomics" and "Warranty" manuals.
  • Page 4 Published by Fujitsu Technology Solutions GmbH A26361-K690-Z220-1-7619, Edition 1 2009/06 Produced by XEROX Global Services...

  • Page 5: Operating Manual

    Introduction Important notes Preparing for use ESPRIMO E Operation Troubleshooting and tips Operating Manual System expansions Technical data Index June 2009 edition...
  • Page 6 ESPRIMO is a registered trademark of Fujitsu Technology Solutions GmbH. Microsoft, MS, MS-DOS, Windows, Windows Vista and Windows NT are registered trademarks of the Microsoft Corporation. VESA and DPMS are trademarks of Video Electronics Standards Association. PS/2 is a registered trademark of International Business Machines, Inc.

  • Page 7: Table Of Contents

    Contents Your ESPRIMO E..........................1 Notational conventions ......................... 2 Important notes ..........................3 Safety notes............................3 Transporting the device ........................3 Cleaning the device ..........................3 Energy saving, disposal and recycling ....................4 CE marking............................4 FCC Class B Compliance Statement ....................5 Preparing for use..........................
  • Page 8 Contents Tips 33 System expansions...........................35 Information about boards ......................35 Opening the casing ..........................36 Closing the casing..........................37 Installing and removing the cross-piece....................38 Replacing rear panel ...........................39 Installing and removing a board ......................41 Installing board in low-profile slot....................41 Removing board from low-profile slot ..................42 Installing and removing board with bracket.................43 Low-Profile boards with adapter ....................48 Installing and removing optional ports ....................49...

  • Page 9: Your Esprimo E

    Your ESPRIMO E..is available with various configuration levels with different hardware and software. In addition, you can install accessible drives (e.g. DVD drive), hard disks and other boards. This manual tells you how to put your device into operation and how to operate it in daily use. This manual applies for all configuration levels.

  • Page 10: Notational Conventions

    Introduction Notational conventions The following symbols are used in this manual: indicates information which is important for your health or for preventing physical damage. indicates important information which is required to use the system properly. ► Text which follows this symbol describes activities that must be performed in the order shown.

  • Page 11: Important Notes

    Important notes In this chapter you will find information regarding safety which it is essential to take note of when working with your device. Safety notes Pay attention to the information provided in the "Safety" manual and in the following safety notes.

  • Page 12: Energy Saving, Disposal And Recycling

    Important notes Energy saving, disposal and recycling Information on these topics can be found on the "Drivers & Utilities" CD or on our website http://ts.fujitsu.com. CE marking CE marking for devices shipped without wireless component up to 15/01/2007 The shipped version of this device complies with the requirements of the EEC directives 89/336/EEC "Electromagnetic compatibility"...

  • Page 13: Fcc Class B Compliance Statement

    ● Consult the dealer or an experienced radio/TV technician for help. Fujitsu Technology Solutions GmbH is not responsible for any radio or television interference caused by unauthorised modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Fujitsu Technology Solutions GmbH. The correction of interferences caused by such unauthorised modification, substitution or attachment will be the responsibility of the user.
  • Page 14 Important notes A26361-K690-Z220-1-7619, edition 1...

  • Page 15: Preparing For Use

    Preparing for use Please take note of the safety information in the "Important notes" chapter. Unpacking and checking the delivery It is recommended not to throw away the original packaging material! It may be required for reshipment at some later date. ►...

  • Page 16: Setting Up The Device

    Preparing for use Setting up the device When installing your device, give consideration to the safety notes in the "Safety" manual. Only install the device in the operating positions for which it is intended. We recommend that you place your device on a surface with good anti-slip qualities. In view of the multitude of different finishes and varnishes used on furniture, it is possible that the rubber / plastic feet will mark the surface they stand on.
  • Page 17 Preparing for use Vertical operating position Proceed as follows to operate the device in the vertical operating position: ► If necessary, disconnect the cables. ► Position the casing vertically so that the ON/OFF switch is located at the bottom. ► Pull off the foil from the rubber / plastic feet that you will find in the accessories package.

  • Page 18: Connect The Monitor, Mouse And Keyboard

    Preparing for use Connect the monitor, mouse and keyboard The ports for the monitor, mouse, and keyboard are on the front and rear of the device. Keyboard port / purple PS/2 mouse port / green USB port / black Monitor port / blue Connecting the monitor ►...

  • Page 19: Connecting The Mouse

    Preparing for use Connecting the mouse Depending on the equipment level selected, your device will be supplied with a PS/2 mouse or a USB mouse. Connecting a PS/2 mouse ► Connect the PS/2 mouse to the PS/2 mouse port of the device. Connecting USB mouse ►...

  • Page 20: Connecting The Device To The Mains Voltage

    Preparing for use Connecting the device to the mains voltage ► Connect the power cable to the device (1). ► Plug the power plug into a grounded mains outlet (2). A26361-K690-Z220-1-7619, edition 1...

  • Page 21: Indicators Provided By The Device

    Preparing for use Indicators provided by the device The indicators are on the front of the casing. Which indicators are available on your device depends on the configuration level you have selected. 1 = CD-ROM or DVD indicator 3 = Power-on indicator 2 = Floppy disk indicator/SmartCard reader 4 = Hard disk indicator indicator...
  • Page 22 Preparing for use 1 - CD-ROM or DVD indicator The indicator lights up when the CD-ROM or DVD drive is accessed. You may only remove the CD/DVD when the indicator is dark. 2 - Floppy disk indicator or SmartCard reader indicator Floppy disk indicator: The indicator lights up when the floppy disk drive of the device is accessed.

  • Page 23: Initial Switch-On: Software Will Be Installed

    Preparing for use Initial switch-on: Software will be installed If the device is integrated into a network, the user and server details as well as the network protocol are required during the software installation. Contact your network administrator if you have any questions about these settings.

  • Page 24: Switching On Monitor And Device

    Consult the operating system manual if there is anything unclear about the requested input data. Further information about the system, drivers, utilities and updates can be found on the "Drivers & Utilities" CD or on our website http://ts.fujitsu/support.com. A26361-K690-Z220-1-7619, edition 1...

  • Page 25: Connecting External Devices

    Preparing for use Connecting external devices Read the documentation on the external device before connecting it. With the exception of USB devices, always remove all power plugs before connecting external devices! Do not connect or disconnect cables during a thunderstorm. Always take hold of the actual plug.

  • Page 26: Ports Provided By The Device

    Preparing for use Ports provided by the device The connections are located on the front and back of the device. The ports available on your device depend on the configuration level you have selected. The standard ports are marked with the symbols shown below (or similar).

  • Page 27: Connecting External Devices To The Parallel Or Serial Port

    Preparing for use Connecting external devices to the parallel or serial port If your device has parallel and serial ports, you can connect external devices to these ports (such as a printer or modem). ► Connect the data cable to the external device. ►...
  • Page 28 Preparing for use A26361-K690-Z220-1-7619, edition 1...

  • Page 29: Operation

    Operation Switching the device on ► If necessary, switch the monitor on (see the operating manual for the monitor). ► Press the ON/OFF switch on the front of the device. The power-on indicator lights green and the device is started. Switching off the device ►...

  • Page 30: Keyboard

    Operation Keyboard 1 = Function keys 4 = Cursor keys 2 = Power button (optional) 5 = Numeric keypad (calculator keypad) 3 = Alphanumeric keypad The illustrated keyboard is an example and may differ from the model you use. Important keys and key combinations The description of the following keys and key combinations applies to Microsoft operating systems.
  • Page 31 Operation Start key calls up the Windows Start menu. (Windows XP) (Windows Vista) Menu key invokes the menu for the marked item (Windows). Shift key enables upper-case letters and the upper key symbols to be used. Alt Gr (e.g. German keyboard) Alt Gr produces a character shown on the right-hand side of a key (e.g.

  • Page 32: Working With Floppy Disks

    Operation Working with floppy disks Follow the instructions supplied by the vendor of the floppy disks. Do not clean the floppy disk drive with cleaning floppy disks. Any attempt would destroy the read/write head in the disk drive within 20 seconds. Insertion direction Label area Write protection tab for a 1.44 Mbyte floppy disk...

  • Page 33: Settings In Bios Setup

    Operation Settings in BIOS Setup In BIOS Setup you can set the system functions and the hardware configuration of the device. When the PC is delivered, the default entries are valid (see "BIOS Setup" manual and if necessary manual for the mainboard). You may customise these settings to your requirements in the BIOS Setup. Property and data protection Software functions and mechanical locking offer a broad range of functions for protecting your device and your personal data from unauthorised access.
  • Page 34 Operation Locking the casing Unlocking the casing ► Turn the key in the direction of the ► Turn the key in the direction of the arrow (1). arrow (2). A26361-K690-Z220-1-7619, edition 1...

  • Page 35: Anti-Theft Protection And Lead-Sealing

    Operation Anti-theft protection and lead-sealing Anti-theft protection You can protect your device from theft. ● with the Kensington Lock device (1) and with a Kensington MicroSaver. Consult the manual for your Kensington Lock. ● with the eye (2), a padlock and a chain, which you have connected to a fixed object beforehand.

  • Page 36: Access Authorisation Via Smartcard

    Operation Access authorisation via SmartCard In systems equipped with a SmartCard reader, access can be restricted to those users who have a corresponding SmartCard. Access protection with SystemLock With SystemLock you can protect your system from unauthorised booting. Then a system can only be booted when the user inserts a valid SmartCard in the SmartCard reader and enters his/her personal code number (PIN).

  • Page 37: Troubleshooting And Tips

    Troubleshooting and tips Take note of the safety notes in the "Safety" manual and in the "Preparing for use" chapter, when you connect or disconnect cables. If a fault occurs, try to correct it as described in the following places: ●...

  • Page 38: The Device Cannot Be Switched Off With The On/Off Switch

    Troubleshooting and tips The device cannot be switched off with the ON/OFF switch Cause: The device has not been switched on with the ON/OFF switch. ► Press the ON/OFF switch again. Cause: System crash ► Press the ON/OFF switch for at least 4 seconds, until the device switches off. The operating system is not shut-down properly in the process.
  • Page 39 Troubleshooting and tips Wrong monitor has been set under Windows 2000 ► Restart the device. ► If the message Starting Windows appears, press function key F8 The Windows 2000 Advanced Options Menu appears. ► Select Safe Mode or Safe Mode with Network. ►...

  • Page 40: No Mouse Pointer Displayed On The Screen

    Troubleshooting and tips No mouse pointer displayed on the screen ► Shut down the operating system properly. ► Switch off the device. ► Check that the mouse cable is properly connected to the system unit. If you use an adapter or extension lead with the mouse cable, check the connections. ►...

  • Page 41: The Floppy Disk Cannot Be Read Or Written

    Troubleshooting and tips The floppy disk cannot be read or written ► Check that the write protection of the floppy disk or the floppy disk drive is activated (refer to the "BIOS Setup" manual and if necessary to the manual for the mainboard). ►...
  • Page 42 Troubleshooting and tips A26361-K690-Z220-1-7619, edition 1...

  • Page 43: System Expansions

    System expansions As the device has to be shut down in order to install/deinstall system hardware components, it is a good idea to print out the relevant sections of this chapter. It may be necessary to update the BIOS when carrying out a system expansion or hardware upgrade.

  • Page 44: Opening The Casing

    System expansions Opening the casing ► Switch off the device. The device must not be in the energy-saving mode! Please take note of the safety information in the "Important notes" chapter. Pull the power plug out of the mains outlet! ►...

  • Page 45: Closing The Casing

    System expansions Closing the casing ► Place the top cover on the casing base (1) so that the distance (a) is approximately 2 cm. Ensure that the top cover of the casing engages in the guide rails in the lower part of the casing.

  • Page 46: Installing And Removing The Cross-Piece

    System expansions Installing and removing the cross-piece ► Open the casing (see "Opening the casing"). Removing the cross-piece ► Lift off the cross-piece upward at the marking (a) in the direction of the arrow. Installing the cross-piece ► Insert the cross-piece into its guide lugs (a) on the front of the casing at an angle from above.

  • Page 47: Replacing Rear Panel

    System expansions Replacing rear panel ► Open the casing (see "Opening the casing"). ► Remove the cross-piece (see "Removing the cross-piece"). ► If necessary, remove the board bracket (see "Removing board bracket"). ► Disconnect the power supply connector (1) from the mainboard and the drives. ►...
  • Page 48 System expansions A = Rear panel for low-profile boards B = Rear panel for long boards ► Place the new rear panel on the casing in the direction of the arrow (1). ► Fasten the new rear panel with the four screws (2). ►...

  • Page 49: Installing And Removing A Board

    System expansions Installing and removing a board Please take note of the section "Information about boards". There is a corresponding rear panel for both low-profile boards and long boards. The number, position and arrangement of the board slots on the mainboard can be found in the manual for the mainboard.

  • Page 50: Removing Board From Low-Profile Slot

    System expansions Removing board from low-profile slot ► Open the casing (see "Opening the casing"). ► Disconnect the cables connected to the board. ► Press on the locking lever in the direction of the arrow (1), unhook it and swing it up in the direction of the arrow (2).

  • Page 51: Installing And Removing Board With Bracket

    System expansions Installing and removing board with bracket You can install both low-profile boards and long boards in the board bracket. Removing board bracket ► Open the casing (see "Opening the casing"). ► Remove the cross-piece (see "Removing the cross-piece”). ►...
  • Page 52 System expansions Installing board in bracket ► Make the required settings for the board. Do not dispose of the slot cover. For cooling, protection against fire and in order to comply with EMC regulations, you must refit the slot cover if you remove the board. ►...
  • Page 53 System expansions ► Push the board up to its slot in the direction of the arrow as far as the stop. ► Press the board into the slot so that it engages. ► Fold up the retaining bracket so that it engages.
  • Page 54 System expansions Removing board from bracket ► Disconnect the cables connected to the board. ► Press on the retaining bracket in the direction of the arrow and fold it down. ► Pull the board out of the slot of the board bracket in the direction of the arrow.
  • Page 55 System expansions ► Push the slot cover into the slot in the direction of the arrow. Ensure that the point of the slot cover engages on the outside of the board bracket. ► Fold up the retaining bracket so that it engages.

  • Page 56: Low-Profile Boards With Adapter

    System expansions Low-Profile boards with adapter To also install low-profile boards in long board slots, you must mount a corresponding slot adapter beforehand The slot adapter is located on the slot cover of the upper slot. ► Unscrew the screw that connects the slot adapter to the slot cover. Mounting slot adapter ►...

  • Page 57: Installing And Removing Optional Ports

    System expansions Installing and removing optional ports An additional port (serial or parallel) can be installed in a rear slot cover plate like a board. For an exact description of how to connect external devices to ports, refer to the documentation for the external device.

  • Page 58: Removing An Optional Port

    System expansions Removing an optional port ► Open the casing (see "Opening the casing"). ► Disconnect the cable from the connector on the mainboard. ► Press on the locking lever in the direction of the arrow (1), unhook it and swing it up in the direction of the arrow (2).

  • Page 59: Installing And Removing The Graphics Card

    System expansions Installing and removing the graphics card The outermost slot in your device is specially designed for graphics cards (e.g. PCI Express Low Profile). Installing the graphics card ► Open the casing (see "Opening the casing"). For devices with low-profile slots ►...

  • Page 60: Removing The Graphics Card

    System expansions Removing the graphics card ► Open the casing (see "Opening the casing"). For devices with low-profile slots ► Open the locking lever (see "Installing board in low-profile slot"). ► Press against the ledge of the slot (2) to release the graphics card from the slot. ►...

  • Page 61: Installing And Removing Drives

    System expansions Installing and removing drives In the standard model the device may be equipped with the following drives: ● one accessible 3 ½ inch drive (floppy drive) ● one non-accessible 3 1/2 inch drive (hard disk) ● one accessible 5 ¼ inch drive (e.g. DVD or CD ROM drive) ●...

  • Page 62: Installing And Removing Plastic Drive Covers

    System expansions Installing and removing plastic drive covers Removing plastic drive cover If you install an accessible drive in the 3 ½ inch installation bay and this bay was previously empty or contained the second hard disk, you must first remove the plastic drive cover. ►...
  • Page 63 System expansions ► Press the plastic drive cover from the inside into the front panel in the direction of the arrow until you feel it latch into place. ► Close the casing (see "Closing the casing"). A26361-K690-Z220-1-7619, edition 1...

  • Page 64: Replacing Drive In 5 ¼ Inch Bay

    System expansions Replacing drive in 5 ¼ inch bay ► Open the casing (see "Opening the casing"). Removing a drive ► Pull the data and the power supply connectors from the desired drive. ► Press the EasyChange rails (1) together and pull the drive out of the casing (2).
  • Page 65 System expansions Installing a drive ► Take the new drive out of its packaging. ► Adjust the required settings on the drive (if necessary, on already-installed drives as well). ► Press the EasyChange rails into the provided holes. ► Push the accessible drive into the casing until the EasyChange rails engage.

  • Page 66: Folding Up And Down The Drive Cage

    System expansions Folding up and down the drive cage ► Open the casing (see "Opening the casing"). ► Remove the cross-piece (see "Removing the cross-piece”). Also observe the sticker on the drive cage. Folding up the drive cage ► Open the lock of the drive cage by pressing the catch (a) lightly in the direction of the arrow (1).

  • Page 67: Replacing The Floppy Disk Drive

    System expansions Replacing the floppy disk drive ► Open the casing (see "Opening the casing"). ► Remove the cross-piece (see "Removing the cross-piece”). ► Fold up the drive cage (see "Folding up and down the drive cage"). Removing the floppy disk drive ►...
  • Page 68 System expansions Installing the floppy disk drive ► Push the drive into the casing in the direction of the arrow (1). ► Fold up the drive cage (see "Folding up the drive cage"). ► Fasten the floppy disk drive with the screws (2). ►...

  • Page 69: Replacing Hard Disk

    System expansions Replacing hard disk ► Open the casing (see "Opening the casing"). ► Remove the cross-piece (see "Removing the cross-piece”). ► Remove the data and the power supply connectors from the mainboard. ► Disconnect the power supply connector from the hard disk. ►...
  • Page 70 System expansions Removing the hard disk ► Remove all connected cables (1) from the hard disk. ► Press the lever of the hard disk carrier in direction of the arrow (2). ► Remove the hard disk with the bracket out of the device in the direction of the arrow (2).
  • Page 71 System expansions Installing the hard disk ► Remove the new hard disk from the package. ► Pull the support rail (1) of the bracket somewhat toward the outside. ► Place the hard disk into the hard disk carrier in the direction of the arrow (2). Make sure that the bracket pins engage in the holes of the hard disk.
  • Page 72 System expansions ► Fold down the power supply in the direction of the arrow (1) until the power supply engages. ► Press on the locking lug (2) of the drive cage and then fold the drive cage with light pressure in the direction of the arrow (3) until the lever engages.

  • Page 73: Replacing Second Hard Disk In 3 ½ Inch Drive Cage

    System expansions Replacing second hard disk in 3 ½ inch drive cage ► Open the casing (see "Opening the casing"). ► Remove the cross-piece (see "Removing the cross-piece”). ► Fold up the drive cage (see "Folding up the drive cage"). Removing second hard disk ►...

  • Page 74: Replacing Second Hard Disk In 5 ¼ Inch Drive Carrier

    System expansions Replacing second hard disk in 5 ¼ inch drive carrier ► Remove the drive carrier as described in "Replacing drive in 5 ¼ inch bay" chapter. Removing the hard disk ► Remove the screws (1). ► Pull the hard disk out of the drive carrier in the direction of the arrow (2). Installing the hard disk ►...

  • Page 75: Installing/Removing A Smartcard Reader And/Or Wlan Module (Optional)

    System expansions Installing/removing a SmartCard reader and/or WLAN module (optional) You can also install a SmartCard reader and/or a WLAN module for wireless LAN (Local Area Network) in place of the drive in the installation bay of the floppy disk drive. The SmartCard reader and WLAN module can be installed together in the carrier.
  • Page 76 System expansions Removing SmartCard reader from carrier ► Loosen the screws (1). ► Pull the SmartCard reader out of the carrier in the direction of the arrow (2). Removing WLAN module from carrier ► Loosen the screws (1). ► Pull the WLAN module out of the holder in the direction of the arrow.

  • Page 77: Installing Smartcard Reader And/Or Wlan Module

    System expansions Installing SmartCard reader and/or WLAN module ► Open the casing (see "Opening the casing"). ► Remove the cover from the upper casing top cover if necessary (see "Removing plastic drive cover"). ► Remove the cross-piece (see "Removing the cross-piece"). ►...

  • Page 78: Removing Smartcard Reader And/Or Wlan Module

    System expansions Removing SmartCard reader and/or WLAN module ► Open the casing (see "Opening the casing"). ► Remove the cross-piece (see "Removing the cross-piece”). ► Fold up the drive cage (see "Folding up the drive cage"). ► Remove the screws (1). ►...

  • Page 79: Extensions To The Mainboard

    System expansions Extensions to the mainboard The description of how to upgrade the main memory and/or processor is contained in the manual for the mainboard. ► Open the casing (see "Opening the casing"). ► Fold up the drive cage (see "Folding up the drive cage"). Upgrading main memory ►...

  • Page 80: Replacing Lithium Battery

    System expansions Replacing lithium battery In order to permanently save the system information, a lithium battery is installed to provide the CMOS-memory with a current. A corresponding error message notifies the user when the charge is too low or the battery is empty. The lithium battery must then be replaced. Incorrect replacement of the lithium battery may lead to a risk of explosion! The lithium battery may be replaced only with an identical battery or with a type recommended by the manufacturer.

  • Page 81: Technical Data

    200 mm Vertical operating position: ● front min. 200 mm ● rear min. 200 mm The data sheet of the device contains further technical data. You will find the data sheet on the internet at http://ts.fujitsu.com/ A26361-K690-Z220-1-7619, edition 1...
  • Page 82 Technical data A26361-K690-Z220-1-7619, edition 1...

  • Page 83: Index

    Index indicator 14 CE certificate 4 CE marking 4 3 1/2-inch drive 53 Chain 27 Class B Compliance Statement 5 Clearance 73 5 1/4-inch drive 53 Configuration, BIOS Setup 25 Connecting keyboard 11 Access permission, SmartCard 28 mouse 11 Additional serial port, installing 49, 50 PS/2 mouse 11 Anti-theft protection 27 standard keyboard 11...
  • Page 84 Index Drive 53 accessible 53 Hard disk changing 56 changing 61, 65 installing 53 installing 61, 63, 65, 66 non-accessible drive 53 removing 61, 62, 65, 66 removing 53 Hard disk contents, restoring 33 Drive cage 58 Hard disk indicator 14 fold down 58 Headphones 18 fold up 58...
  • Page 85 Index Line in 18 Operation 21 Line out 18 Other manuals 33 Lithium battery 71 replacing 72 Lock 25 Packing material 7 Low voltage directive 4 unpacking 7 Low-profile boards 48 Parallel port 18, 19 mounting slot adapter 48 connecting devices 19 removing slot adapter 48 settings 19 Plastic drive cover...
  • Page 86 Index indicator 14 installing 67, 69 USB 10 operating 28 Universal Serial Bus 18 removing 67, 70 USB devices Software connecting 19 installing 15, 16 software 19 new installation 29 USB port 11, 19 Standard keyboard, connecting 11 connecting devices 19 Summer time 33 connecting keyboard 11 Surface 73...

Table of Contents