Table of Contents
Advertisement
entis INFRA-RED REMOTE CONTROL with AUTO TIMER.
POWER ON/OFF:
be on, but it is likely that is not so. To turn on the remote control (it is protected with a "kiddy lock"),
press and hold the POWER button for about 2 seconds until "off" disappears from the screen, then
release to unlock the safety feature. One short press of the POWER button will turn on power to the
remote control, and also start the fire on the MANUAL - HIGH setting. Current mode / settings will be
displayed. The fire will always start in manual operating mode on a high setting. (Also refer to the next
page for further information). There is an audible beep when the fire receives a signal from the remote,
range is approximately 5 metres.
CLOCK SETTING:
WEEK to set the week day, press HOUR to set the hour, taking care to check if on a.m. or p.m. Press
MIN to set the minute (holding the button down will advance the minutes quicker). Press CLOCK to
save the setting.
MANUAL "FLAME" OPERATING MODE h
fixed to the setting and needs to be adjusted manually by pressing TEMP control " – " and " + " buttons.
"FUZZY LOGIC" OPERATING MODE r
levels". Press MODE to switch between Manual and Fuzzy Logic, and use the TEMP " – " and " + "
buttons. Choose the comfort level that best suits your needs. Every now and then the fire will give a
short boost of heat and then return to your chosen setting. This is the most economical way to operate
your Yunca Fuzzy Logic control fire.
HINT: The two speed fan is designed to quickly transfer heat around the room and ensures the most
economic gas use. The three-position switch (LOW/OFF/HIGH) is located on the fan box (ref page 3),
and is accessible from near the centre of the bottom air vent.
AUTO FUNCTION:
above), and ensure the CLOCK time and day are correctly set. PLEASE NOTE: If a key is not pressed
for 7 seconds, the programming will "time out" and you will need to re-start the process.
Set times to Start and/or Stop the fire with a choice of up to two daily programme settings (PROG1 and
PROG2). You can choose to use only PROG1 if only one setting is needed. Heat output on Auto is
initially run in manual control, and once the fire is operating you can then switch to the more economical
Fuzzy Logic.
EXAMPLE: Set PROG1 to start at 6:00 am, stop at 8.00am. Set PROG2 to start at 4.30pm, stop at
10.30pm Monday to Friday. Both PROG1 and PROG2 may have different settings programmed for the
weekend if required.
TO SET: Press PROG1 to set the "timer on" setting (Mon-Fri). Now choose the desired heat output
(High, Med or Low) Press HOUR button, making sure you have chosen the correct a.m. or p.m. time,
then press MIN button (increases in 10 minute steps) to set the start time. Press PROG1 again and use
the HOUR / MIN buttons to set the stop time. Press CANCEL at any time to clear the setting currently
on screen (i.e.either Start or Stop). If you are not setting weekend programming, just press PROG1 to
save your settings and exit the programming function.
If you wish PROG1 to operate on Saturday and Sunday, press WEEK button to set start time, using
HOUR and MIN buttons as described above. Then press PROG1 again to set the weekend stop time,
and press PROG1 once more to save your settings and exit the setting mode.
Continue as above using PROG2 if required. To check the programme settings press either Prog1 or
Prog2.
Revised 22-08-07
First check that the two AAA batteries are inserted. The remote may appear to
Press the CLOCK button once ("clock" in the display will start flashing). Press
To set this feature you will need to ensure the remote control is on (as advised
Yunca entis instal Aug07
as three settings: High, Medium, Low. Heat output is
eplaces the traditional thermostat operation with six "comfort
...Important Info
continued on following page
Page 13 of 23
Advertisement
Table of Contents
