Advertisement
MAINTENCE, CARE AND REPAIR
Switch off and unplug the machine before carrying out
any cleaning or maintenance work.
CLEANING
Wear personal protection equipment during cleaning
Do not use water or flammable liquids to clean the sander,
clean with a soft brush.
FAULTS
Switch OFF immediately at the mains plug and
remove the plug when:
•
The plug or cable is damaged.
•
The switch on the machine is defective.
•
You smell or see smoke caused by scorched insulation
in the machine.
Replacing the soles
When the Velcro has worn out replace the sander soles.
Spares are available from the Helpline number.
Remove the abrasive
•
Remove the sole and replace with a new one.
•
Reinstall on the machine.
Overheating
•
Put less pressure on the workpiece.
•
The dust is not removed.
•
Check holes in sander sole are clear and line up with
holes in the abrasive sheet.
•
Clean the dust extraction opening.
The machine does not start when switched on
•
Check the mains lead and the fuse/plug.
•
Take to your Ferm Dealer for repair
The motor is defective
Take to your Ferm Dealer
There are no user serviceable/repairable parts inside this
machine. Qualified service engineers must carry out repairs
and servicing.
Lubrication
The machine requires no user lubrication.
MAINTAIN TOOLS WITH CARE
Keep the tool clean for better and safer performance.
Follow instructions for changing accessories. Inspect tool
and extension cables periodically and if damaged, have them
repaired by a qualified person or authorised service body.
Check for damaged parts
Do not use a tool with damaged parts, before further use
a damaged tool must be carefully checked by a qualified
person to determine that it will operate properly. Check
for alignment of moving parts, binding or breakage of
parts, mounting and other conditions that may affect its
operation.
A damaged part or guard should be properly repaired by an
authorised service centre, unless indicated otherwise in the
instruction manual. Have defective switches replaced by an
authorised service centre. Do not use a tool if the switch
does not turn on and off.
6
Have your tool repaired by an expert
This appliance is manufactured in accordance with rele-
vant safety standards. Only experts must carry out repai-
ring of electrical appliances, otherwise considerable dan-
ger for the user may result.
Storing tools
When not in use tools should be stored in the dry, out of
reach of children.
ELECTRICAL INFORMATION
This product is double insulated in accordance with EN
50144 – no earth wire is required.
It is supplied with a pre-wired mains plug, if the plug needs
replacing follow these instructions.
Wire correctly
The wires in the mains lead are coloured in the following way:
BLUE
-Neutral
BROWN
-Live
Fuse
(5 Amp)
Blue
(Neutral)
Brown
(Live)
Securing wires
Secure wires carefully and firmly to the correct termi-
nals. Secure the mains cable in the plug cord grip firmly
Fit a 3-amp fuse. If a 13amp (BS1363) plug is used a (BS
1362) ASTA approved 3-amp fuse must be fitted.
Recycle/Dispose of old plug and cable
Prevent inadvertent connection to socket and risk of
electric shock
ENVIRONMENT
Recycle the packaging according to the identification
marks on it.
At the end of the product or its accessories life please
recycle where facilities exist - phone the Helpline for
current advice on recycling.
Helpline
For any questios relating to operational or safety
matters contact:
Ferm Customer Helpline on:
0115 966 1199
Monday-Friday
8am – 6pm
Saturday
9am – 1 pm
GUARANTEE
The guarantee conditions can be found on the separately
enclosed guarantee card.
ı
CE
DECLARATION OF CONFORMITY
We declare under our sole responsibility that this
product is in conformity with the following
standards or standardized documents
EN50144-1, EN50144-2-4,
EN55014-1, EN55014-2,
EN61000-3-2, EN61000-3-3
in accordance with the regulations.
98/37EEC
73/23EEC
89/336EEC
from 01-10-2000
GENEMUIDEN NL
W. Kamphof
Quality department
Ferm
Ferm
( UK )
7
Advertisement
