Table of Contents
Advertisement
Quick Guide
XX214-20-03
Surveyor® HD Series Network
Camera Domes
Vicon Industries Inc.
Tel: 631-952-2288 Fax: 631-951-2288 Toll Free: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: 44/(0) 1489-566300
Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the
operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed
to be used in life-critical situations and must not be used for this purpose.
www.vicon-security.com
Document Number: 8009-8214-20-03
Issued: 1013
Product specifications subject to change without notice.
Copyright © 2013 Vicon Industries Inc. All rights reserved.
Advertisement
Table of Contents
Related Manuals for Vicon XX214-20-03
Summary of Contents for Vicon XX214-20-03
- Page 1 24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: 44/(0) 1489-566300 Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed to be used in life-critical situations and must not be used for this purpose.
- Page 2 The Surveyor HD supports high-profile H.264 or M-JPEG compression. The dome supports ONVIF open architecture connectivity to enable integration into third party software recording solutions, as well as Vicon’s ViconNet. The Surveyor HD is designed for easy installation and serviceability. The entire drive assembly simply snaps into the housing.
-
Page 3: Installation
Quick Operation Guide Installation In-Ceiling... - Page 4 Quick Operation Guide Pendant...
- Page 5 Quick Operation Guide Pressurized...
- Page 6 Quick Operation Guide Wiring and Setup CONNECTOR/PIN CONNECTOR TYPE CONNECTOR/PIN LABEL SIGNAL NAME NUMBER TERMINAL BLOCK POWER (TB2) TB2-1 TB2-2 Neutral TERMINAL BLOCK ALARM (TB1) TB1-1 ALARM 1 Alarm I/O 1 TB1-2 Ground TB1-3 ALARM 2 Alarm I/O 2 TB1-4 Ground TB1-5 ALARM 3...
-
Page 7: Setting The Dip Switches
Quick Operation Guide Setting the DIP Switches There are two DIP switches that must be set on the Surveyor HD. One is on the Communications Interface (CI) board and one on the Main board. SW1 4-position DIP switch is on the Communication Interface (CI) board. For SW1 all poles should be set to OFF (default). -
Page 8: Communication Ports
Quick Operation Guide Position 5 – Unused (set to OFF) Position 6 - Unused (set to OFF) Position 7 – Set password. OFF = Default Position. ON = Reset to default password (password); must be reset to OFF after reboot and before next power up. - Page 9 Quick Operation Guide Pressurized Cable Preparation Using the prefabricated cable Using a customer prepared cable...
-
Page 10: Using The Web Browser Interface
Quick Operation Guide Using the Web Browser Interface Web Browser Interface The Web Browser Interface provides a user friendly interface to configure and control various features and functions of the Surveyor™ HD camera dome. The interface allows the configuration of camera dome parameters, viewing live video, using PTZ, setting administrative controls and collecting camera dome reports and status information. - Page 11 Quick Operation Guide Login The initial screen prompts the user to login with a user name and password if at least one user account has been programmed in the camera dome. Upon first use, the default user name is admin and the password is password.
- Page 12 Quick Operation Guide A user name and password are required to log on to the camera dome. The Add/Edit screen allows user accounts to be setup. A maximum number of 10 users can be entered. The Settings area allows for configuration of a variety of controls, including Transmission, Image, Analytics (for future release), Date/Time, Network and Port, Alarms/Relay, Schedule, PTZ and SD Card.
- Page 13 Quick Operation Guide and Nucleus IP address. Diagnostic Features can be turned on or off. Manually reboot the camera by clicking the Restart Camera button; click Restore Defaults to return all Maintenance settings, except Network settings, to their default values •...
- Page 14 Vicon Industries Inc. For office locations, visit the website: www.vicon-security.com...
Need help?
Do you have a question about the XX214-20-03 and is the answer not in the manual?
Questions and answers