Table of Contents
Advertisement
Quick Links
X940-04-05
MODEL VIST35 AND VIST25 SERIES
PAN-AND-TILT DRIVES
Copyright © 2002 Vicon Industries Inc. All rights reserved.
Product specifications subject to change without notice.
Vicon and its logo are registered trademarks of Vicon Industries Inc.
VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788
TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266)
UK: 44/(0) 1489-566300 WEB: www.vicon-cctv.com
Vicon part number 8006-8940-04-05
Rev 1202 Section 2
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Vicon ViStar VIST35 Series
Summary of Contents for Vicon ViStar VIST35 Series
- Page 1 Copyright © 2002 Vicon Industries Inc. All rights reserved. Product specifications subject to change without notice. Vicon and its logo are registered trademarks of Vicon Industries Inc. VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788 TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116 24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: 44/(0) 1489-566300 WEB: www.vicon-cctv.com...
-
Page 5: Table Of Contents
Contents Introduction ............................1 Installation............................3 Unpacking and Inspection ........................3 Inspection For Visible Damage......................3 Inspection For Concealed Damage ....................... 3 Mounting the Unit ..........................3 Inverted Mounting..........................5 Mounting the Camera .......................... 5 Connector Assembly..........................6 Housing Output Connector Assembly....................10 Adjusting the Limit Stops........................ - Page 7 Use only with a mounting accessory recommended by Vicon, or sold with the video product. Any mounting of the video product should follow Vicon’s instructions, and a mounting accessory recommended by Vicon should be used.
- Page 8 16. Overloading - Do not overload wall outlets and required, be sure the service technician has used extension cords as this can result in a risk of fire or replacement parts specified by Vicon or that have the electric shock. same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other 17.
-
Page 9: Introduction
Introduction The information in this manual covers the installation, operation, and maintenance of the ViStar Series of Pan- and-Tilt Drives. This unit should only be installed by a qualified technician using approved materials in accordance with national, state and local wiring codes. Read this manual through completely before attempting installation. - Page 10 Table 2 Maximum Operating Distances Pan-and-Tilt Control Wire Size Maximum (AWG) Distance Annealed ft (m) Copper 360 (110)* VIST35 560 (170)* VIST35-P Any appropriate 900 (275)* VIST35-RP 24 VAC output 1420 (433)* VIST35-AP control or receiver 250 (76.2)** VIST25-VP V1305R-DC VIST25-VRP Distance from control to pan-and-tilt.
-
Page 11: Installation
Installation Unpacking and Inspection All Vicon equipment is tested and inspected before leaving the factory. It is the carrier’s responsibility to deliver the equipment in the same condition as it left the factory. Inspection For Visible Damage Immediately inspect the cartons upon delivery. Make a note of any visible damage on all copies of the carrier’s freight bill. - Page 12 The mounting base of the pan-and-tilt can accommodate many Vicon mounts and accessories. The base offers three mounting configurations, so that Vicon medium-duty, heavy -duty, and UK standard mounts can be accommodated. Choose the appropriate mount for the combined weight of the pan-and-tilt and camera/housing assembly.
-
Page 13: Inverted Mounting
There are three mounting slots on the camera mounting plate. To obtain optimum balance, the screw(s) used to mount the camera or camera/housing assembly can be placed in any of these slots. These slots follow Vicon’s standard housing mounting hole pattern to accommodate all Vicon light- and medium-duty housings, as well as UK standard housings and accessories. -
Page 14: Connector Assembly
Connector Assembly Assemble an interconnecting cable according to the procedures that follow. Refer to Figure 3 for connector locations. Refer to Figure 5 and accompanying tables for pin connections. The parts for the connector assembly are provided in the accessory kit. Caution: Do not apply 230 VAC through VIST35-RP and VIST25-VRP slip ring (continuous rotation) versions. - Page 15 Figure 4 Connector Assembly Caution: If the V1305R-DC receiver is used with a VIST25, a shielded cable must be used. The shield’s ends are required to be connected to the ground of both the VIST25 and V1305R-DC. Avoid bundling the video wire with the rest of the wires in this harness.
- Page 16 Input Connector Assembly Pin Connection Table - VIST35 Series Refer to Figure 5 Function VIST35 VIST35-P VIST35-RP VIST35-AP Pin No. Pin No. Pin No. Pin No. TILT COMMON TILT UP TILT DOWN PAN COMMON PAN RIGHT PAN LEFT GROUND AUTOPAN (see note below) NOT USED NOT USED NOT USED TILT PRESET FEEDBACK...
- Page 17 Pin Connection Table - VIST25 Series Refer to Figure 5 Function VIST25-VP VIST25-VRP Pin No. Pin No. NOT USED TILT UP TILT DOWN NOT USED PAN RIGHT PAN LEFT GROUNDww NOT USED TILT PRESET FEEDBACK P/T PRESET SUPPLY PAN PRESET FEEDBACK P/T PRESET GROUND 24 VAC+ NOT USED...
-
Page 18: Housing Output Connector Assembly
Figure 6 Connecting the Ground/Shield Housing Output Connector Assembly The VIST35-RP and VIST25-VRP have a housing output connector (refer to Figure 3) that allows functions to be wired through the pan-and-tilt to a camera housing mounted on the pan-and-tilt. The mating connector for this connector is the same type as that used for the base, except that it is the male connector. -
Page 19: Adjusting The Limit Stops
Pin Connections for VIST35-RP and VIST25-VRP Housing Output Connector Function Function Function CAMERA POWER +, 2 A max. ZOOM PRESET FEEDBACK NOT USED CAMERA POWER -, 2 A max. LENS PRESET SUPPLY NOT USED GND/LENS PRESET GND NOT USED NOT USED SHIELD VIDEO SIGNAL NOT USED... - Page 20 Caution: Removing one or both movable pan limit stops voids the warranty and may result in damage to the unit. The VIST35-RP and VIST25-VRP have no pan stops. To adjust limit stops on all models proceed as follows. Refer to Figure 8. Figure 8 Pan-and-Tilt Limit Stop Adjustments To adjust pan limits:...
- Page 21 Autopan Adjustments To adjust the limits on the VIST35-AP: After the manual limit stops are set, proceed as follows to set the autopan limit stops. Refer to Figure 9. Caution: The pan-and-tilt will start to move suddenly. Be sure that the unit is secure before performing this procedure and keep hands away from moving parts.
-
Page 22: Preset Position Adjustments
Figure 9 VIST35-AP Adjustments Preset Position Adjustments The preset position versions of the ViStar pan-and-tilt must be used with one of the NOVA (VPS) system digital controls or the Vicoax V1902VCT digital control. To program presets, follow the instructions provided with the control unit. -
Page 23: Operation
Operation When the unit is wired to an appropriate control unit, movements along two axes, pan and tilt, are possible. Refer to the instruction manual for the particular control for detailed instructions. Note: Operating the VIST35-P, VIST35-AP, VIST25-VP, VIST35-RP and VIST25-VRP models with preset requires the use of a control with preset position capability. -
Page 24: Shipping Instructions
Shipping Instructions Use the following procedure when returning a unit to the factory: 1. Call or write Vicon for a Return Authorization (R.A.) at one of the locations listed below. Record the name of the Vicon employee who issued the R.A. -
Page 25: Reference
Caution: Careful selection of the proper cable is essential to obtain the best performance from this equipment. Vicon assumes no responsibility for poor performance when cables other than those recommended are installed. In all cases, coaxial cable impedance should be 75 ohms. -
Page 26: Technical Information
Technical Information ELECTRICAL Input Voltage: VIST35 series: 24 VAC. VIST25 series: 24 VDC. Power Consumption: VIST35: 14.4 W, pan; 14.9 W tilt. VIST25: 8.4 W, pan; 24.2 W, tilt. Maximum value at rated load. Heat Equivalent: VIST35: 1.7 btu/min (0.4 kg-cal/min). VIST25: 1.9 btu/min (0.5 kg-cal/min). - Page 27 OPERATIONAL Angular Travel: Pan: VIST35-V, 360° maximum; VIST35-P/VIST35-AP/VIST25-VP series, 320°; VIST35-RP/VIST25-VRP series, unlimited pan. Tilt: +26° to -85°. Stops: Externally adjustable. Speed: VIST35 series Pan: 6°/sec. Tilt: 3°/sec. VIST25 series Pan: 1-48°/sec. Tilt: 1-24°/sec. Load Rating: VIST35 series: 35 lb (16 kg). VIST25 series: 25 lb (11 kg).
- Page 28 Gears: Steel. Seals: O-ring and weatherproofing gaskets for all-weather environmental protection. Mounting: Pan-and-Tilt Base: three mounting hole patterns to accommodate a variety of mounting configurations, including standard UK configurations. Refer to Figure 1. Camera/Housing: three tray slots accommodate a variety of camera/housing mounting patterns, including standard UK housing configurations.
- Page 29 Notes Technical Information • • 21 X940-04-05 Rev 1202 ViStar...
- Page 30 Vicon Industries Inc. Corporate Headquarters 89 Arkay Drive Hauppauge, New York 11788 631-952-CCTV (2288) 800-645-9116 Fax: 631-951-CCTV (2288) Vicon Europe Headquarters Brunel Way Fareham, PO15 5TX United Kingdom +44 (0) 1489/566300 Fax: +44 (0) 1489/566322 Brussels Office Planet II - Unit E...
Need help?
Do you have a question about the ViStar VIST35 Series and is the answer not in the manual?
Questions and answers