Call Acknowledge; Selcall Memories; Labelling Your Sellcall Idents - GME TX3345 Instruction Manual

if the call is not sent within 10 seconds of entering the
NOTE:
last ident digit the call function will time-out and the radio will
return to normal mode. to exit the mode without sending the
selcall briefly press the CAll button.

CAll ACKnowleDge

if your selcall transmission is successful, the radio you called
should respond with an 'acknowledge' signal – usually two
quick beeps. this will confirm to you that the radio you called
is now alerting its user to your signal.

selCAll MeMories

your radio is fitted with a 'call' memory, an 'id' memory and
10 user programmable storage memories as follows:
1. 'Call' memory – always holds your last-sent selcall ident
making it easy to resend it.
2. 'Id' memory – holds your radio's own selcall ident. you
should only select this memory location if you need to
change your radio's factory programmed selcall ident.
3. user programmable storage memories – can be used
to store and recall frequently called selcall idents. memories
are labelled 'c0' to 'c9'.
To store a Selcall Ident in memory
1. Briefly press the CAll button.
the last sent or received selcall ident.
2. Press the or
location 'c0' to 'c9' (to change your radio's own selcall
ident, select 'id'). if an AlPhA label is displayed you will
need to press then
MENU
F
LVL
3. Press and hold the
PRI
right-hand digit of the selcall ident will flash.
4. Press the or
in the flashing digit position.
5. Briefly press the
LVL
PRI
position.
t X 3 3 4 5
is displayed along with
keys to select the required memory
to switch to numeric mode.
SQL
ALPHA
key until the radio beeps. the
keys to select the required number
key again to select the next digit
6. repeat steps 4 and 5 to enter all 5 digits as required.
7. now press and hold the
flash for a few seconds then the radio will beep as the new
ident is stored.
Recalling Selcall Idents from memory
1. Briefly press the CAll button.
the last sent or received selcall ident.
2. Press the
memory in locations 'c0' to 'c9'.
3. Press and hold the CAll button to send the ident.
Changing your radio's own Selcall Ident
1. Ensure your radio is in numeric mode (press
as required until 'numEr' is displayed).
SQL
ALPHA
2. Briefly press the CAll button.
the last sent or received selcall ident.
3. Press the
radios own selcall ident.
4. Press and hold the
right-hand digit of the selcall ident will flash.
5. Press the
in the flashing digit position.
6. Briefly press the
position.
7. repeat steps 5 and 6 to enter all 5 digits as required.
8. now press and hold the
flash for a few seconds then the radio will beep as the new
ident is stored.
lAbelling your selCAll iDents
you can label each selcall ident using a 5 character name to
make it easier to identify callers. if an incoming selcall matches
one of those in your radio's memory, the label can be displayed
instead of the selcall ident.
i n s t r u c t i o n m A n u A l
LVL
key. the entire ident will
PRI
is displayed along with
or keys to select the required ident
is displayed along with
key. 'id' will be displayed along with your
LVL key until the radio beeps. the
PRI
or keys to select the required number
LVL
key again to select the next digit
PRI
LVL
key. the entire ident will
PRI
then
MENU
F
PA G E 1 5