Electrolux EDW 1001 Service Manual page 32

6.13 6XPPDU\ RI 6HUYLFH DQG &XVWRPHU 6XSSRUW )XQFWLRQV
S 1 S 4
L D1 L D4
S 2 S 5
L D2 L D5
S 3 S 6
L D3 L D1 2
Tastenanordnung senkrecht
XurÃphyyvtÆr…‰vprÃsˆp‡v‚†Ãtrr…hyy’Á‚Ã…v†vtÃ…‚t…h€Ã€h’ÃirÆryrp‡rqÄÃÃÃÃÃ6yyrÐrv‡r…rÃ9h‡rÃ†vqÃqr€Ã“ˆtru|…vtrÃ
hx‡ˆryyrÃQsyvpu‡rurs‡Ã“ˆÃr‡ru€rÃÄ
Function
S1 + S2
Water Hardness
then additionally
Setting
S0 (ON/OFF)
Switching Off the
S1 + S2
Rinsing Agent
then additionally
Display S0 (ON/OFF)
S1 + S3
Manufacture
then additionally
Test Program
S0 (ON/OFF)
S2 + S3
Individual Actuator
then additionally
Control
S0 (ON/OFF)
Output Customer
S2 + S3
Support Error
then additionally
S0 (ON/OFF)
Memory
Clearing the
S2 + S3
Customer Support
then additionally
Error Memory
S0 (ON/OFF)
LED Test
Exiting the
6yyÃÃTr…‰vprÃhqÃ8ˆ†‡‚€r…ÃTˆƒƒ‚…‡ÃAˆp‡v‚†ÃphÃ‚y’ÃirÃr‘v‡rqÃi’Ðh’ÂsÃxr’ÃTÃi’Ɛv‡puvtÃPAAÇurÀhpuvrÃÃ
Exception: Hardness Range Setting - You can leave this function also when after the last pushbutton operation on S1 60 seconds have passed.
functions
L D8 L D 9
L D7 L D1 0
L D6 L D1 1
L D1 3
L D1 4
LED Display
operation
Í
LD1 and LD2
Í
flashing
Í
LD1 and LD2
Í
flashing
Í
LD3
Í
after 3 sec.
flashing
Í
LD1 + LD2 + LD3
Í
flashing
Í
LD1 + LD2 + LD3
Í
flashing
Í
LD1 + LD2 + LD3
Í
flashing
L D1
L D0
S 1
S 0
Tastenanordnung waagrecht
Selection resp. Start of Function
by key
LED Display
LD1
Í
lights up for 5sec.
S1
Then display of new H value
by coded flashing
Rinsing agent active:
Í
LD2 and "END" flashing
S2
Rinsing agent OFF
LD2
flashing
Program
Í
start
LD3
flashing
auto-
matically
Í
LD2
S2
flashing
LD1
Í
flashing
S1
Error display coded via PAA
LED's.
3 times short lighting up of
Í
all existing LED's with an
S3
approx.bBreak of 2
sec.each time.
L D 2 L D3 L D4 L D 5
L D8 L D9
L D7 L D1 0
L D6 L D1 1
L D1 2
S 2 S 3 S 4 S 5 S 6
L D1 3
L D1 4
Short description/remarks
For detailed description see page B 7
Í
"Water hardness settings"
For detailed description see page B 8
Í
"Switching off the rinsing agent display"
Manufacture test program is carried out
automatically.
Í
For detailed description see pag B 9
"Calling the manufacture test program"
Order of activated actuators:
Valve > Dosing combination > Recycling pump > Heating
Í > Fan > Reg.dos > El.pump > all OFF
For detailed description see page B 10
"Individual actuator control"
For detailed description see pages
Í
"Output Customer Support Error Memory" /
"Overview Error Displays"
The activation of this function will clear the
Customer Support Error Memory
Í
For detailed description see page B 10
"Clearing the Customer Support Error
Memory and LED Test"
L D 0
S 0
B 10 / B
13