Electrolux EDW 1001 Service Manual page 29

6.10 6HUYLFH )XQFWLRQ  6ZLWFKLQJ RII WKH ULQVLQJ DJHQW GLVSOD\
ÃÃÃXurÃphyyvtÆr…‰vprÃsˆp‡v‚†Ãtrr…hyy’Á‚Ã…v†vtÃ…‚t…h€Ã€h’ÃirÆryrp‡rqÄÃÃ
General Information
Function is not generelly available.
This function must be programmed in the software model.
w
For deactivating or activating the rinsing agent dosage,
you will need the keys S0, S1 and S2, independently of
their model-related program assignment.
w
If rinsing agent dosage is activated, this will be displayed by
the LED's LD2 and (position-independently) LED "END".
L D 1 S 1
Tastenanordnung
L D 2 S 2
senkrecht
L D 1L D 2
Tastenanordnung
waagrecht
S 1 S 2
I
1RWH
This function is used to switch off the rinsing agent
display ONLY. It is generally not possible to switch off the
rinsing agent dosage.
If a certain model is not provided with rinsing agent LED,
this function cannot be displayed!
Brr…hyy’Ãhƒƒyvphiyr)
w
Key S2 is ALWAYS the "rinsng agent key"
w
In the works, rinsing agent display has been activated.
Brr…hyÃr‘ƒyvph‡v‚†Ã‡‚Ãxr’ÃG@9ÃU
w
This key LED only lights up or flashes, if
the function has been programmed on this machine model.
If the backlit function is not available on a certain
model, the respective LED is switched off in the mode Service Functions.
Aufrufen / Ändern / Speichern der Klarspüleranzeige
L D 0
S 0
K lar s püler anz eige
ak tivier t
L D 0
S 0
K lar s püler anz eige
aus
... AU S nach 6 0s ek . automatis ch
Ã)
1.
S 1
S 2
blink en
2.
S 1
L D0
L D1
L D2
S 2
S 0
3.
L D0
L D1
L D2
S 2
blink en
4.
L D0
L D2 S 2
L E D
" E NDE "
blink t!
bl ink en
5.
L D0
L D2
S 2
bl ink en
6.
L D0
L D 2 S 2
L E D
" E NDE "
aus !
L D0
... AU S dur ch manuel le B etäti gung über E in/Aus
8hyyvtÃhqÃpuhtvtÇurÃ…v†vtÃhtr‡Ãqv†ƒyh’Ãsˆp‡v‚)Ã
Press keys S1 and S2 simultaneously and ...

... Keep them pressed until the machine is switched on
!
with the ON/OFF key S0. For acquittal, the respective key LED's
LD1 and LD2 are flashing.
Press the key S1 in order to call the "rinsing agent display" function.
"
The key LED LD2 is flashing.
#
When the rinsing agent display is activated, the END LED will
also be flashing.
The "END" LED position can vary depending upon the
model programming.
(see description page B 6 / item "Program flow display")
By pressing key S2, you can now activate or
$ÃÃ%
deactivate the rinsing agent display.
Rinsing agent display active:
Key LED's LD2 and "END" LED are both flashing.
Rinsing agent display inactive:
KeyLED LD2 is flashing.
T‡‚…vtÇurƇh‡ˆ†Ã†r‡‡vt)
The setting is stored immediately upon each single input.
@‘v‡vtÇurÃsˆp‡v‚
L D0
After 60 seconds after the last pushbutton operation on key
key S2 or by switching the machine off by use of the ON/OFF key
S 0
S0, you automatically leave the special program.