IDEAL Evomax 30 Installation & Servicing Manual page 30

38 EVomAX uSER IntERfACE - bASIC oPERAtInG InStRuCtIonS
SEttInG fLoW tEmPERAtuRE
Press SELECT and a screen similar to the following will be displayed
The kW output number in the 1st line will vary depending the
maximum output of the boiler
Ideal Evomax 80kW
normal operation
Set Flow Temp'
Set DHW Temp'
Rotate the KNOB clockwise until a screen similar to the following
is displayed
Ideal Evomax 80kW
Normal Operation
Set flow temp'
Set DHW Temp'
Set Off/Sum/Win
Press SELECT and a screen similar to the following will be displayed
Set Flow Temp'
80°C
Press + and - to change to the required setting and then press
ENTER to store
Rotate the KNOB anti-clockwise until Normal Operation is
highlighted again and press SELECT to return to normal operation
SEttInG DomEStIC Hot WAtER tEmPERAtuRE
Note that DHW Temperature can only be set if a DHW Thermistor has
been connected to the boiler and the boiler configured for its use.
Press SELECT and a screen similar to the following will be displayed
The kW output number in the 1st line will vary depending the
maximum output of the boiler
Ideal Evomax 80kW
normal operation
Set Flow Temp'
Set DHW Temp'
Rotate the KNOB clockwise until a screen similar to the
following is displayed
Ideal Evomax 80kW
Set Flow Temp'
Set DHW temp'
Set Off/Sum/Win
Out' Sensor Slope
Press SELECT and a screen similar to the following will be displayed
Set DHW Temp'
65°C
Press + and - to change to the required setting and then press ENTER
to store
Rotate the KNOB anti-clockwise until Normal Operation is highlighted
again and press SELECT to return to normal operation
30
InStALLAtIon
SEttInG SummER, WIntER AnD StAnDby oPERAtIon
Note that Standby Mode will disable Domestic Hot Water and
Central Heating, Summer Mode will disable Central Heating
Press SELECT and a screen similar to the following will be displayed
The kW output number in the 1st line will vary depending the
maximum output of the boiler
Ideal Evomax 80kW
normal operation
Set Flow Temp'
Set DHW Temp'
Rotate KNOB clockwise until a screen similar to following is displayed
Ideal Evomax 80kW
Set DHW Temp'
Set Off/Sum/Win
Out' Sensor Slope
Normal Operation
Press SELECT and a screen similar to the following will be displayed
Set Off/Sum/Win
Standby
Summer
Winter
Press - for more
Press + and - to change to required setting, press ENTER to store
Rotate the KNOB anti-clockwise until Normal Operation is highlighted
again and press SELECT to return to normal operation
SEttInG tHE outSIDE SEnSoR SLoPE
Note that an Outside Sensor must be fitted to the boiler for this feature
to be active (this will be detected automatically)
Press SELECT and a screen similar to the following will be displayed
The kW output number in the 1st line will vary depending on the
maximum output of the boiler
Ideal Evomax 80kW
normal operation
Set Flow Temp'
Set DHW Temp'
Rotate KNOB clockwise until a screen similar to following is displayed
Ideal Evomax 80kW
Set Off/Sum/Win
out' Sensor Slope
State of Inputs
State of Outputs
Press SELECT and a screen similar to the following will be displayed
Out' Sensor Slope
Note that a higher number gives a higher room temperature and a
lower number gives a lower room temperature
Press + and - to change to required setting, press ENTER to store
Rotate the KNOB anti-clockwise until Normal Operation is
highlighted again and press SELECT to return to normal operation
1.5
EVOMAX -
Installation & Servicing
continued . . . . . . . .