IDEAL Evomax 30 Installation & Servicing Manual page 29

37 bASIC ContRoLS DISPLAy ContInuED......
Central Heating mode
If there is an ongoing Central Heating Demand screens similar to
the following will be displayed
Line 2 indicates whether Switched Live or OpenTherm is controlling
the boiler
Line 3 indicates the current operating State (Pre-Purge or Ignition or
Burner On or Pump Overrun)
Outside temperature will only be shown if an outside sensor is
connected to the boiler
Burner Power and Flow Temp will vary as the boiler operates
See Frame 42 for adjusting Flow Setpoint
boiler frost Protection mode
If the boiler flow temperature drops below 5°C screens similar to
the following will be displayed
Line 3 indicates the current operating State (Pre-Purge or
Ignition or Burner On or Pump Overrun)
Outside temperature will only be shown if an outside sensor is
connected to the boiler
Burner Power and Flow Temp will vary as the boiler operates
System frost Protection mode
If an Outside Sensor is fitted and the Outside Temperature drops below the system frost protection
temperture setpoint a screen similar to the following will be displayed
Line 3 indicates the current operating State (Pre-Purge or Ignition or Burner On or Pump Overrun)
Flow Temperature and Outside Temperature will vary as the boiler operates
See Frame 42 for adjusting the system frost protection temperature setpoint.
Cylinder frost Protection mode
If a Domestic Hot Water Thermistor is connected to the boiler and
the DHW temperature drops below 5C a screen similar to the
following will be displayed
Line 3 indicates the current operating State (Pre-Purge or Ignition
or Burner On or Pump Overrun)
Burner Power, Hot Water Temp' and Outside Temp' will vary as
the boiler operates
Outside temperature will only be shown if an outside sensor is
connected to the boiler
0-10V Capacity operating mode
If 0-10V Capacity operation is ongoing screens similar to the
following will be displayed
Line 3 indicates the current operating State (Pre-Purge or Ignition
or Burner On or Pump Overrun)
Flow Temp' and Burner Power will vary as the boiler operates
0-10V Input and Burner Setpoint Target will vary as the external
Building Management System controls them
See Frame 40 for configuring the boiler for 0-10V Capacity
Operation
0-10V temperature operating mode
If 0-10V Temperature operation is ongoing screens similar to the
following will be displayed
Line 3 indicates the current operating State (Pre-Purge or
Ignition or Burner On or Pump Overrun)
Flow Temp' and Burner Power will vary as the boiler operates
0-10V Input and Flow Setpoint will vary as the external Building
Management System controls them.
See Frame 40 for configuring the boiler for 0-10V Temperature
Operation.
EVOMAX -
Installation & Servicing
InStALLAtIon
Central Heating
CH Switched Live On
Burner On
Flow Setpoint
Flow Temp
Boiler Frost Protect
Burner Power
Burner On
Frost Setpoint
Flow Temp
Cylinder Frost Protect
Burner Power
Burner On
Frost Setpoint
Hot Water Temp'
0-10V Operation
0-10V Input =
Burner On
Burner Setpoint Target
Flow Temp
0-10V Operation
0-10V Input =
Burner On
Flow Setpoint
Flow Temp
Central Heating
Burner Power
Outside Temp'
80°C Flow Setpoint
80°C Flow Temp
Boiler Frost Protect
100% Burner Power
Outside Temp'
5°C Frost Setpoint
80°C Flow Temp
System Frost Protect
Flow Temp
Burner On
Frost Setpoint
Outside Temp'
Cylinder Frost Protect
100% Burner Power
Outside Temp'
5°C Frost Setpoint
4°C Hot Water Temp'
0-10V Operation
10.0V Burner Power
Burner On
100% Burner Setpoint Target
Flow Temp
80°C
0-10V Operation
10.0V Burner Power
Burner On
80°C Flow Setpoint
Flow Temp
80°C
continued . . . . . . . .
100%
10°C
80°C
80°C
100%
10°C
5°C
80°C
80°C
-10°C
10°C
100%
10°C
5°C
4°C
100%
100%
80°C
100%
80°C
80°C
29