System Setting; System Mode; Option Mode - Panasonic AJ-SDX900E Operating Instructions Manual

CONTENTS
Chapter 7 Menu description tables
7-2

SYSTEM SETTING

7-2-1

SYSTEM MODE

Variable
Item
range
CAMERA MODE 50i For selecting the camera's operation mode.
25P 50i: The camera operates in the 50i mode.
25P: The camera operates in the 25P mode.
V.RES (25P) INTRLCE For selecting the vertical resolution when 25P
PROG. is selected.
INTRLCE: Line mixing is used to produce
PROG.:
<Note>
If PROG. is selected the images produced are
25P segment frame images, so true 25P
editing is possible. However, adding vertical
detail (V.DTL) will cause the images to appear
less natural. It is therefore recommended that
V.DTL be set to 0. (The images will retain
sufficient vertical response after 25P editing
even if V.DTL is set to 0.)
REC MODE 16:9/50M For selecting the mode in which to record the
4:3/50M signals on the VTR.
16:9/25M 16:9/50M: <16:9> signals are recorded at 50
4:3/25M
4:3/50M: <4:3> signals are recorded at 50
16:9/24M: <16:9> signals are recorded at 25
4:3/24M: <4:3> signals are recorded at 25
PB MODE MANUAL For selecting the playback mode.
AUTO MANUAL: The playback mode accords with the
AUTO: In this mode, the recording mode is
REC TALLY RED For selecting the method used to inform the
GREEN user that the unit is recording when a system
CHAR using an extender or other device is
configured and BOTH is selected as the 26-
PIN CONTROL menu item setting while the
system is used in the remote control mode.
RED:
GREEN: The green tally lamp lights.
CHAR:
The underlining in the variable range column indicates the setting in the preset mode. The underlining in the variable range column indicates the setting in the preset mode.
78
Remarks
more natural images.
No line mixing is used, allowing
true 25P images to be obtained
when editing following shooting.
Mbps.
Mbps.
Mbps.
Mbps.
25M or 50M setting of the REC
MODE item.
Operation proceeds with 16:9 or 4:3
read from the tape.
automatically detected and playback
is performed in the same mode.
The red tally lamp lights.
The letters "REC" appear on the
viewfinder.
7-2-2

OPTION MODE

Variable
Item
range
P.OFF GPS DATA HOLD For selecting whether or not to hold the UMID
CLEAR GPS position information while the power is
off and record the information as the data still
held as the previous value until another
measurement can be taken after the power is
next turned on.
HOLD: The data is held and recorded.
CLEAR: The data is cleared at the same time
COMPONENT OUT ON For selecting whether or not component
OFF output from pins 26 and 68 continue during
power save status.
ON: Output continues.
OFF: Output stops during power save. (Note
26PIN CONTROL OFF For setting the 26-pin control mode.
BOTH OFF:
BOTH: Control over both the unit and 26-pin
26PIN CTL NORMAL For selecting the portable to be used (for
DEFAULT SPECIAL switching the VTR/SS initial status).
NORMAL: Initially "L": AJ-D92
SPECIAL: Initially "H"
SDI EMBEDDED ON For setting whether or not to output the audio
AUDIO OFF signals to SDI.
SDI METADATA ON For setting whether or not to output the
OFF metadata to SDI.
SDI EDH ON For setting whether or not to add the error
OFF detection flags to the SDI output.
Remarks
as the power is turned off, and all
zeros (no information) are recorded
from the time the power is turned on
until the measurement is next taken.
that this setting is forced ON if a
camera adapter is connected and a
tally signal is detected from pin 26.
Otherwise it is OFF.)
Only the unit is controlled. (No 26-pin
control).
connector is exercised. The tally LED
indicates the status of the 26-pin tally
signal. (The unit's recording can be
set using the REC TALLY item on the
SYSTEM MODE menu.)