Panasonic AJ-SDX900E Operating Instructions Manual page 40

CONTENTS
Chapter 4 Adjustments and settings for recording
Display item What is displayed
ABB ACTIVE
4 Camera warning
and message ABB OK
display area ABB BREAK
(Displays related to ABB NG
the AWB, ABB and W-SHD ACTIVE
switch operations) W-SHD OK
W-SHD BREAK
W-SHD NG
B-SHD READY
B-SHD ACTIVE
B-SHD OK
B-SHD BREAK
B-SHD NG
B-SHD LVL OVER
(Switch selection
WHITE: # ¢.¢K
displays)
AUTO KNEE: ON/OFF
GAIN: ¢¢dB
SS: 1/¢¢¢¢
SS: 1 1/¢¢¢¢
SS: SUPER V
CC: ¢¢¢¢ ¢¢K
ND: ¢
EXTENDER: ON/OFF
IRIS: ¢¢ F ¢ ¢
(LOW LIGHT LOW LIGHT
warning display)
(Y GET value)
¢¢¢.¢%
(CALL display) CALL
(MARKER display) MKR: A/B/OFF
INH
5 Information
allocated to USER S.GAIN ¢¢dB/OFF
buttons DS.GAIN ¢¢:/OFF
S.IRIS ON/OFF
UM: USER MAIN
I.OVR ON/OFF
U1: USER1 button
S.BLK –¢¢/OFF
U2: USER2 button
B.STR ON/OFF
AUDIO CH1
AUDIO CH2
40
This appears during an ABB operation.
This appears when the ABB operation has been completed satisfactorily.
This appears when the ABB operation has been forcibly terminated.
This appears when the ABB operation has not been completed satisfactorily.
This appears during a WHITE SHADING operation.
This appears when the WHITE SHADING operation has been
completed satisfactorily.
This appears when the WHITE SHADING operation has been forcibly
terminated.
This indicates that white shading has not been completed satisfactorily
LVL OVER as the brightness level was excessively high during the WHITE
SHADING operation.
This appears when the BLACK SHADING operation is ready to be
performed as a result of holding down the ABB switch for a length of
time during an ABB operation.
This appears during a BLACK SHADING operation.
This appears when the BLACK SHADING operation has been
completed satisfactorily.
This appears when the BLACK SHADING operation has been forcibly
terminated.
This appears when the BLACK SHADING operation has been not
completed satisfactorily.
This warns the user that the brightness is too high during the BLACK
SHADING operation.
This appears when the position of the WHITE BAL switch has been
changed. "A," "B" or "PRE" appears at #. VAR ¢.¢ K is displayed
when channel A, Y is set to VAR. ATW MODE is displayed when ATW
is assigned to channel B.
This appears when the AUTO KNEE switch has been set to ON or OFF.
This appears when the gain has been selected using the GAIN selector
switch or USER button.
This indicates the shutter speed value when the shutter speed has been
selected.
This appears when synchro scan has been selected as the shutter
speed.
This appears when SUPER V has been selected as the shutter speed.
This appears when the CC filter setting has been selected.
This appears when the ND filter setting has been selected.
This appears when the lens extender has been set to ON or OFF.
This appears when the iris overwrite correction value has been changed.
This appears when the brightness has dropped.
With the Y GET ON setting, the output brightness level near the centre
marker is displayed as "%."
This appears when the call command has been issued from the extender.
This indicates the type of marker presently being displayed.
"INH" is indicated when the operation of the USER button has been disabled.
This indicates the value selected for S.GAIN.
This indicates the value selected for DS.GAIN.
This indicates whether S.IRIS is set to ON or OFF.
This appears when the IRIS OVERRIDE setting is enabled (ON).
This indicates whether SUPER BLACK is set to ON or OFF and, if it is
set to ON, it also indicates its value.
This indicates whether BLACK STRETCH (black level gradation
compensation) is set to ON or OFF.
This appears when the input signal to recorded on audio channel 1 has
been switched.
This appears when the input signal to recorded on audio channel 2 has
been switched.
Status when display appears