Table of Contents
Advertisement
ENGLISH
Keep the supporting surfaces clean
– in particular, remove resin residue
with a suitable cleaning and mainte-
nance spray.
11. Available accessories
For special tasks the following accesso-
ries are available at your specialized
dealer – see back cover for illustrations:
A
Dust collection attachment
Protects your health and keeps the
shop clean.
B
Dust spout adaptor
To connect the dust collection
attachment to a dust collector.
C
Work clamp
Required for precision cuts and cut-
ting of non-ferrous metals.
D
Table extension, left
Required for cutting long stock;
extends to 3000 mm;
folds for space saving storage.
E
Table extension, right
Required for cutting long stock;
extends to 3000 mm;
folds for space saving storage.
F
Work stand
For a secure machine stand and
optimal working height;
folding, ideal for mobile use.
G
TCT saw blade 250 x 2.8 / 2.0 x 30
24 alternate bevel teeth
for wood and non-laminated parti-
cle board.
H
TCT saw blade 250 x 2.4 / 1.8 x 30
48 alternate bevel teeth
For wood and panels.
I
TCT saw blade 250 x 2.4 / 1.8 x 30
60 alternate bevel teeth
For wood, panels and thick-walled
plastic extrusions
15. Technical specifications
Voltage
Current draw
Fuse protection
Motor capacity* (power input P1, S6 20% - 5 min)
Protection class
Degree of protection
Saw blade speed
Cutting speed
Saw blade diameter (outer)
Arbor bore
Dimensions
Machine in packing
Length / width / height
Machine ready to work, rotating table in 90°position, c/w suction port
Length / width / height
26
J
TCT saw blade 250 x 2.8 / 2.0 x 30
80 trapezium-flat teeth
For wood, panels, ducting, NF
extrusion,
high-quality
sheets and laminates.
12. Repairs
A
Danger!
Repairs to electric tools must
be carried out by qualified electri-
cians only!
Electric tools in need of repair can be
sent to the service centre of your coun-
try. Refer to the spare parts list for the
address.
Please attach a description of the fault to
the electric tool.
13. Environmental Protection
The machine's packing can be 100%
recycled.
Worn out power tools and accessories
contain considerable amounts of valua-
ble raw and rubber materials, which can
be recycled.
These instructions are printed on paper
produced with elemental chlorine-free
bleaching process.
14. Trouble Shooting
In this section problems and faults are
described which you may remove your-
self. If the measures detailed here do not
solve the problem, see under "Repairs".
A
Danger!
Many accidents happen partic-
ularly in connection with problems
and faults. Therefore please note:
Always unplug before servicing.
Check that all safety devices are
operational again after each fault
service.
veneered
Motor does not run
No mains voltage
Check cables, plug, outlet and
mains fuse.
No crosscut function
Transport locking pin engaged:
Pull transport locking pin out.
Safety lock engaged:
Actuate the safety lock.
Only little sawing performance
Saw blade blunt (possibly tempering
marks on blade body):
Saw blade not suitable for material being
cut (see chapter "Technical specifica-
tions");
Saw blade warped:
Replace saw blade (see chapter
"Maintenance").
Saw vibrates heavily
Saw blade warped:
Replace saw blade (see chapter
"Maintenance").
Saw blade incorrectly mounted:
Mount saw blade correctly (see
chapter "Maintenance").
Saw squeals when starting
Drive belt tension too low:
Retension the drive belt (see chap-
ter "Maintenance - Drive belt ten-
sioning").
Stiffness of rotating table
Saw dust build-up under rotating table:
Remove saw dust.
V
230 (1 50 Hz)
A
8.4
A
10 (time-lag)
kW
1.8
IP
20
II
-1
min
5020
m/s
66
mm
250
mm
30
mm
800 / 600 / 450
mm
575 / 885 / 595
110 (1 50 Hz)
15.9
-
1.6
20
II
5020
66
250
30
800 / 600 / 450
575 / 885 / 595
Hide quick links:
Advertisement
Table of Contents
