Table of Contents
Advertisement
8. Available accessories
For special tasks the following accesso-
ries are available at your specialized
dealer – see back cover for illustrations:
A
Saw blade SP 600 x 2.8 x 30 56
KV
Standard saw blade
B
Saw blade CV 600 x 2.8 x 30
56 WZ
CV steel, for hardwoods and soft
wood.
C
Saw blade HW 600 x 3.9/2.8 x 30
26 WZ
Tungsten carbide tipped, espe-
cially
for
hardwoods
extended edge life.
9. Repairs
A
Danger!
Repairs to electric tools must
be carried out by qualified electri-
cians only!
Electric tools in need of repair can be
sent to the service centre of your coun-
try. Refer to the spare parts list for the
address.
Please attach a description of the fault to
the electric tool.
12. Technical specifications
Electrical data
Voltage
Nominal current
Fuse protection min. (time-lag or K-type breaker)
Protection class
Motor:
Power input P1
Power output P2
Speed
Saw blade
Maximum diameter (outer)
Arbor bore diameter (inner)
Thickness
Maximum cutting speed
Maximum dimensions of logs to be cut
Maximum diameter (reversing cut)
Minimum diameter
Maximum length
Minimum length
Machine dimensions
Length
Width
Height
Machine weight
* The values stated here only indicate the loudness emitted by this machine. Whether the operator is required to wear hearing pro-
tection can not be determined here. This depends on how much noise reaches the ear of the operator. And this, among other
things, depends on the existing ambient conditions (such as other sources of noise near by). Even though it may not be explicitly
required, it is in your own interest to always wear hearing protection when operating this machine.
10. Environmetal protection
The machine's packing can be 100%
recycled.
Worn out electric tools and accessories
contain considerable amounts of valua-
ble raw and plastic materials, which can
be recycled.
These instructions are printed on chlo-
rine-free bleached paper.
11. Trouble shooting
A
Danger!
Before carrying out any fault
and
an
service or maintenance work, always:
switch machine OFF;
unplug power cable;
wait for saw blade to come to
standstill.
Check that all safety devices are
operational again after each fault
service.
Motor does not run
No mains voltage:
check cables, plug, outlet and mains
fuse.
Mains voltage too low:
Use power cable of sufficient lead
cross section (see "Technical speci-
fications").
No-voltage release solenoid tripped by
temporary power failure:
switch on again.
Overload protection tripped:
let motor cool down for approx. 10 min-
utes, then start motor again.
Motor lo cked, e.g. by a blocked saw
blade:
Remove cause for blocking, let
motor cool down if necessary, then
start motor again.
Incorrect rotational direction of saw
blade
Phase sequence changed at the phase
changer:
Change direction of rotation (see
"Mains connection").
Poor cutting performance
Saw blade blunt (possibly tempering
marks on blade body):
Have saw blade resharpened or
replace it (see "Maintenance").
Set of teeth insufficient:
Have teeth set properly or replace
saw blade (see "Maintenance").
Saw blade soiled by resin:
Clean saw blade (see "Mainte-
nance").
Wood is too wet:
Let wood try before cutting.
V
400 (3
A
A
kW
4.2 kW S6 40%
kW
2.7 kW S6 40%
-1
min
mm
mm
mm
m/s
mm
mm
mm
mm
mm
mm
mm
kg
ENGLISH
50 Hz)
6.5
10
IP 54
1250
600
30
2.8
39
210
25
1000
300
1225
795
1050
102
15
Advertisement
Table of Contents
