Stop Button [5]; Fade/Wipe Effects; Picture Wipe Or Dissolve Selection - JVC GR-DV2000 Instructions Manual

32
RECORDING
EN

Fade/Wipe Effects

These effects let you make pro-style scene
transitions. Use them to spice up the transition
from one scene to the next. You can also vary
transitions from scene to scene.
IMPORTANT:
Some Fade/Wipe Effects cannot be used with
certain modes of Programme AE with special
effects ( pg. 34, 35). If an unusable Fade/
Wipe Effect is selected, its indicator blinks or
goes out.
Power Switch
Recording Start/
Stop Button
MENU Wheel
To Deactivate The Selected Effect . . .
.... press FADE/WIPE again in step 6 so that
the effect indicator disappears.
NOTES:
Once a Fade/Wipe Effect is executed, the effect is
deactivated and its indicator goes out. To use the
same effect again, press FADE/WIPE as required.
To use a different effect, start from step 4.
You can extend the length of a Fade or Wipe by
pressing and holding the Recording Start/Stop
Button.
If the power is turned off after a scene is finished
recording, the stored point is erased,
disabling the Picture Wipe/Dissolve combina-
tion. When this happens, the Picture Wipe/
Dissolve indicator blinks. Also note that power
shuts off automatically if 5 minutes elapse in the
Record-Standby mode.
Picture Wipe/Dissolve cannot be used when
"CAMERA MODE" is set to "PS-VIDEO".
All Fade/Wipe Effects cannot be used when
"CAMERA MODE" is set to "DUAL".
The sound at the end of the last recorded scene
is not stored.
Advanced Features For Video And D.S.C. (cont.)
Shooting Mode Switch
FADE/WIPE Button
FADE/WIPE SELECTION
( , , ,
Fade or Wipe works when video recording is started or
when you stop recording.
1
Set the Shooting Mode Switch to "VIDEO" and set the
Power Switch to "
Button located on the switch. Pull out the viewfinder
fully or open the LCD monitor fully.
2
Press the MENU wheel. The Menu Screen appears.
3
Set "CAMERA MODE" to "VIDEO" or "PS-VIDEO" in
the Menu Screen (
4
Rotate the MENU wheel to select "
then press it. Rotate the MENU wheel to select the
desired function, then press it. Selection is complete.
5
Press the MENU wheel again. The Menu Screen
closes.
6
To activate the Fade-in or Wipe-in . . .
.... Press FADE/WIPE during Record-Standby mode
so that the selected effect indicator appears.
To activate the Fade-out or Wipe-out . . .
.... Press FADE/WIPE during recording so that the
selected effect indicator appears.
7
Press the Recording Start/Stop Button to activate the
Fade-in/out or Wipe-in/out.

PICTURE WIPE OR DISSOLVE SELECTION

( , , ,
The Picture Wipe or Dissolve works when video recording
is started.
1
Follow steps 1 through 5 above.
2
Engage the Record-Standby mode.
If you press FADE/WIPE during recording . . .
.... press the Recording Start/Stop Button when one
scene is finished. The point at which the scene
ended is stored in memory.
If you press FADE/WIPE during Record-Standby
mode . . .
.... press the Recording Start/Stop Button to start
recording and press it again when one scene is
finished. The point at which the scene ended is
stored in memory.
3
If you start recording a new scene within 5 minutes of
the end of the previous recording (without having
turned the camcorder's power off), the previous scene
wipes out, revealing the new scene.
, , , ,
" while pressing down the Lock
pg. 26, 27).
FADER/WIPE",
, , and
and )
)