Basic Recording For Digital Still Camera; (D.s.c.); Basic Shooting (Snapshot) - JVC GR-DV2000 Instructions Manual

RECORDING
Power Switch
SNAPSHOT
Button
Lock Button
Picture Size
Displays the file size of the stored image: UXGA, XGA
or VGA ( pg. 14).
Picture Quality
Displays the quality of the stored image: FINE or
STD (standard) (in order of quality) (
Number of shots taken
Displays the number of images
that have already been shot.
UXGA F I NE
10 / 24
Total number of shots
Displays the approximate total number of
shots that can be stored, including those
already taken. The number increases or
decreases depending on the shots stored,
the Picture mode, Shooting mode, etc.
Card icon
Appears during shooting and blinks when a
memory card is not loaded.
Shooting icon
Appears and blinks during shooting.
UXGA Mode icon
Displays the process utilized to create the UXGA size
image: (DOUBLE) or
There is the sound of a shutter closing.
Basic Recording For Digital Still Camera (D.S.C.)
Shooting
Mode Switch
pg. 14).
Display
(ENLARGE) ( pg. 14).
Snapshot mode
with no frame

Basic Shooting (Snapshot)

You can use your camcorder as a Digital Still Camera for
taking snapshots.
NOTE:
You should already have performed the procedures listed
below. If not, do so before continuing.
Power ( pg. 6)
Grip Adjustment ( pg. 8)
Viewfinder Adjustment (
Loading A Memory Card (
Picture Mode Setting (
1
Set the Shooting Mode Switch to "XGA/VGA" or "UXGA",
then set the Power Switch to "
down the Lock Button located on the switch. Open the
LCD monitor fully or pull out the viewfinder fully.
2
Press SNAPSHOT halfway. The screen becomes a still
image, which is captured into the camcorder's memory.
However, it is not recorded until SNAPSHOT is pressed
fully.
•At this moment, if you release SNAPSHOT, snapshot
recording will be cancelled.
3
Press SNAPSHOT fully.
The image is recorded in the memory card .
•Still images are recorded in the snapshot mode with no
frame.
To Delete Unwanted Still Images . . .
..... when unwanted still images are stored in the memory
card or its memory is full, refer to "Deleting Images"
( pg. 45) and delete unwanted still images.
To Remove The Shutter Sound . . .
..... when you do not want to hear the shutter sound, set
"BEEP" to "OFF" in the Menu Screen (
sound is no longer heard from the speaker.
NOTES:
Even if "DIS" is set to "ON" (
be disabled.
If Snapshot recording is not possible, "PHOTO" blinks when
SNAPSHOT is pressed.
If Programme AE with special effects (
certain modes of Programme AE with special effects are
disabled during Snapshot recording. In such a case, the icon
blinks.
If shooting is not performed for approx. 5 minutes when the
Power Switch is set to "
from the battery pack, the camcorder shuts off automatically
to save power. To perform shooting again, close the LCD
monitor and re-open it. When using the viewfinder, push
back it in and pull it out again.
The Motor Drive mode (
Shooting Mode Switch is set to "XGA/VGA" or "UXGA".
When a headphone set is connected to the PHONE
connector, the shutter sound is not heard from the speaker.
Still images taken are compliant to DCF (Design rules for
Camera File systems). They do not have any compatibility
with devices which are not compliant to DCF.
In the XGA mode, images shot using a 680,000-pixel
Progressive Scan CCD (effective area: 630,000 pixels, 962 x
654 pixels) are converted and stored in the XGA mode file
size (1024 x 768 pixels).
EN
pg. 8)
pg. 11)
pg. 14)
" or " " while pressing
pg. 26, 29). The
pg. 27), the Stabiliser will
pg. 34) is engaged,
" or " " and power is supplied
pg. 18) is disabled when the
19