Table of Contents
Advertisement
Before starting to build, use the Kit Contents list to take an inventory of your kit to make sure it is complete, and inspect
the parts to make sure they are of acceptable quality. If any parts are missing or are not of acceptable quality, or if you
need assistance with assembly, contact Great Planes Product Support. When reporting defective or missing parts, use
the part names exactly as they are written in the Kit Contents list on this page.
1
8
9
15
5
1/8" x 7/8" x 6" Ply strip (wheel pant mounts)
(4) 1/2" x 1/2" x 5/8" Maple blocks (cowl mnts)
1/4" x 3/4" x 5" Balsa stick (fuel tank support)
3" Spinner
(2) 2" x 3/16" Bolt-on axles
(4) 3/16" Wheel collars
(4) 6-32 Set screws for wheel collars
(2) 5/16" -24 Lock nuts (for axles)
(2) 1/4-20 x 2" Nylon wing bolts
(4) Large control horns
(6) 6-32 Blind nuts (preinstalled)
(2) 1/4-20 Blind nuts (preinstalled)
Inch Scale
0"
1"
0
10
20
30
Metric Scale
KIT CONTENTS
Great Planes Product Support:
Phone: (217) 398-8970
Fax: (217) 398-7721
E-mail: airsupport@greatplanes.com
2
11
14
13
12
16
18
Kit Contents (Not Photographed)
(8) 8-32 x 1" SHCS (socket-head cap screws)
(4-engine mnt to firewall, 4-engine to mnt)
(4) Faslinks
(5) Nylon clevis
(1) 2" x 9" CA hinge strip
(4) 8-32 Blind nuts (engine mount)
(6) 6-32 x 3/4" Screws (landing gear)
(4) 2-56 x 5/8" Screws (elev, rudd control horns)
(4) #2 x 1/2" Screws (aileron control horns)
(4) #2 x 3/8" Screws (wheel pants)
(5) Silicone retainers (clevises)
(4) #8 Flat washers (engine mount)
To convert inches to millimeters, multiply inches by 25.4
2"
3"
40
50
60
70
3
4
6
7
1
10
17
4"
80
90
100 110 120 130 140 150 160 170 180
5
Kit Contents
(Photographed)
1 Wing with Ailerons
2 Fuselage
3 Stab with Elevators
4 Fin with Rudder
5 Painted Cowl
6 Painted Canopy
7 Cockpit
8 Painted Wheel Pants (2)
9 Painted Aluminum Landing
Gear (2)
10 1/4" x 1-1/8" x 10-3/4"
Wing Joiner
11 Fuel Tank with Hardware
12 Tail Gear with Wheel
13 Plywood Servo Tray
14 Engine Mount
15 3" Wheel (2)
16 1/8" Plywood Wing Bolt Plate
17 .074" x 36" Elevator and
Rudder Pushrods
18 Wing Dowels
(1) 3/32" Wheel collar (tail wheel)
(1) 4-40 Set screw (tail wheel)
(1) Brass body screw-lock conn. (throttle servo)
(1) Nylon retainer (screw-lock connector)
(1) 4-40 x 1/4" SHCS (screw-lock connector)
(2) .074" x 6" Pushrod (ailerons)
(1) 3/16" x 12" Guide tube (throttle)
(1) .074" x 18" Pushrod (throttle)
(8) #8 Lock washers (engine, engine mount)
(1) Elevator joiner wire
(4) #4 x 3/8" Screws (cowl)
(4) #4 Washers (cowl)
5"
6"
7"
Advertisement
Table of Contents
