Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Car Solutions QVI-AUD09-V6
Summary of Contents for Car Solutions QVI-AUD09-V6
-
Page 1: Installation Manual
Release date : 2011.07.19 Model : QVI-AUD09-V6 / Product code : AUD09-1107-001 Video Interface for AUDI 2009-2011~ model years With MMI 3G/3G+ head units With external touch screen panel support Installation Manual www.car-solutions.com support@carsolutions.com.ua... -
Page 2: Table Of Contents
Contents 1. Before installation 1.1 Main specifications 1.2 Features 1.3 System diagram 1.4 Components 1.5 Exterior 2. Setup 2.1 DIP switches 2.2 Remote controller 2.3 Original buttons in car 2.4 OSD buttons activation 2.5 OSD Menu (On Screen Display) 2.6 FACTORY mode 2.7 Rear view camera parking guideline 2.8 Touch screen panel calibration 2.9 Remote controller buttons... -
Page 3: Main Specifications
1.1 Main Specifications 1. Inputs (MULTI VIDEO INTERFACE) - 1 x Analog RGBCs (for navigation system) - 1 x REAR-C Input (for external rear camera source, supports NTSC & PAL auto detection) - 3 x A/V Input (for external video source - DVD, TV, DVB-T; supports NTSC &... -
Page 4: Features
1.2 Features DVD, DVB-T and Navigation unit control via external touch screen panel DVD, DVB-T, navigation control via OEM MMI 3G buttons Installation near MMI 3G unit Plug & Play installation (LVDS cable offered) Possibility to adjust position of AV1-3, RGB image ... -
Page 5: System Diagram
1.3 System Diagram MODE Remote Button Switches control MMI 3G UNIT DVD IR TOUCH DVB-T IR CONTROLLER NAVIGATION LVDS INPUT\OUTPUT BOARD RGB input for Navigation unit Video Interface A/V1 Input VIDEO A/V2 Input CIRCUIT External Touch Panel A/V3 Input REAR-C POWER VIDEO Headrest... -
Page 6: Components
1.4 Components OEM cable * 1pc. LVDS cable * 1pc. TOUCH OUT cable * 1pc. IR cable * 1pc. Cable with remote mode switch button * 1pc. RGB cable * 1pc. TOUCH IN cable * 1pc. Rear camera power cable * 1pc. Remote control * 1pc. -
Page 7: Exterior
1.5 Exterior SUB BOARD (47*38*22) ⑦ ⑥ ⑤ ⑪ ⑩ Dimension Horizontal length 146 mm ⑦ ⑥ ⑤ Vertical length 88 mm Height 25 mm ① LED ② POWER/CAN/RGB ③ REAR CAMERA POWER ④ AV (IN/OUT) ⑤ LVDS OUT ⑧ ⑨... -
Page 8: Dip Switches
2.1 DIP Switches Function DIP S/W selection DIP ※ ON : DOWN, OFF : UP DIP # ON : RGB Input is OFF RGB Input [AUDI 2009 LCD 6.5”] OFF : RGB Input is ON - Inputs to be used: A/V3(DVD), CS9100 navigation box (RGB) ON : A/V1 Input is OFF A/V1 Input... -
Page 9: Remote Controller
2.2 Remote Controller Buttons Function POWER & PIP NOT USED MENU OSD Menu Selection or Mode change Move UP Move DOWN Move LEFT (or press 2 sec. – Factory Mode) Move RIGHT (or press 2 sec. - Factory Reset) www.car-solutions.com... -
Page 10: Original Buttons In Car
2.3 Original Buttons on MMI Panel or On Wheel ③ ⑩ ① ⑨ ⑧ ⑤ ④ ② ⑦ ⑥ NAVIGATION control DVD, DVB-T control MODE CHANGE Temporarily NOT USED ① Move UP ⑤ Confirm If there is the MODE handle button on ②... -
Page 11: Osd Buttons Activation
OSD Buttons Activation OSD Buttons for DVD For DVD control via OSD menu installer shall connect DVD system to AV1 input and join “DVD IR” cable from video interface cables with DVD IR receiver DATA cable. First of all, if you touch the screen in mode ”AV1”, you can see the menu as shown left. -
Page 12: Osd Menu (On Screen Display)
2.5 OSD Menu (On Screen Display) OSD menu: Press ”MENU” button on the remote controller Analog RGB mode Analog RGB mode Analog RGB mode Video AV1-3 mode Video AV1-3 mode Video AV1-3 mode IMAGE UTIL - BRIGHTNESS - LANGUAGE : To change DVD, CMMB OSD - FACTORY RESET: To restore - CONTRAST menu language (select 1 among English or... -
Page 13: Factory Mode
2.6 Factory Mode Factory mode: press ◀ button for 2 sec. IMAGE - H-POSITION: horizontal movement of screen (image alignment) - V-POSITION : vertical movement of the screen (image alignment) - NAVI MODEL (RGB input resolution) : DEFAULT – 480x234(400x234), KD900(WVGA) 800x480, MD7000(WVGA) 800x480, MYVI(WVGA) 800x480, PAPAGO(WVGA) 800x480 - CAR MODEL : DEFAULT, 2011 A7,8-NEW... -
Page 14: Rear View Camera Parking Guideline
2.7 Rear View Parking Guideline Factory mode: press ◀ button 2 sec. ① Set “ON” in “PARK ENABLE” line in the PARK section as shown left. (default – ON) . In case camera you want to connect already has parking lines, you should turn this function off in order to avoid parking lines and rear view camera image overlapping. -
Page 15: Touch Screen Panel Calibration
2.8 Touch calibration If you use external touch screen panel for connected DVD player, TV tuner, DVB-T receiver control by OSD buttons, which will emulate remote controller buttons of these devices, you should calibrate the connected touch screen panel. >>> ①... -
Page 16: Remote Controller Buttons
2.9.1 Remote Controller Button Programming OSD buttons value using remote controller supplied together with DVD,TV,DVB-T. If you want to control DVD and DMB models other than SANYO and NECVOX via touch screen (using OSD menu, you can program value of DVD and DMB’ s remote controller which you have. Then you can control DVD and DMB via touch screen. >>>... - Page 17 2.9.2 Remote Controller Button >>> ③ After programming select “INPUT” in OSD menu and Programming Instructions> continued… c. Programmed values will appear as green text in the press “OK”. Then you can see confirmation window as marked area on pressing the button. And the values will be shown above.
-
Page 18: Dvd, Dvb-T Model Selection
2.10 DVD, CMMB Model Selection Factory Default : DVD TYPE – NECVOX/SANYO CMMB TYPE – PIONEER/PANASONIC CMMB TYPE DVD TYPE UTIL – DVD/DMB TYPE If DVD/CMMB type that you want to use is not NECVOX or SANYO, you have to register values of the remote controller that you want to use in the “IR MEMORY”... -
Page 19: Installation Diagram
3.1 Installation Diagram Touch panel not included! NOT INCLUDED! 3G MMI UNIT DISPLAY CS9100 Touch Touch Navigation Screen cable cable Controller Offered LCD cable DIP S/W TOUCH OUT LVDS TO NAVI TO SYS MONITOR VIDEO INTERFACE SUB BOARD TO I/F TOUCH POWER/CAN/RGB R-CAM... -
Page 20: Cautions On Installation
3.2 Cautions on Installation Ignition key should be taken off before starting installation, interface power connection must be the last step in installation. Power cable should be disconnected during interface installation. There should be no electronic devices or magnetic pole around the installation place. ... -
Page 21: Installation
3.3 Installation Rear view of monitor Rear view of MMI 3G unit ① The pictures show rear view of the ② Disconnect original LCD cable from MMI 3G unit and connect it disassembled monitor and MMI 3G unit. to “TO MONITOR” socket of the sub-board. Then connect the LCD cable included in video interface package You can see that original monitor LCD to “TO SYS”... - Page 22 3.3 Installation Navigation unit ② Connect the TOUCH OUT cable enclosed package “TOUCH OUT TO NAVI” socket of the video interface. Then connect its opposite end to the navigation system touch cable or USB Touch ① Connect the TOUCH IN cable to external Screen Controller connected to touch screen flat cable.
-
Page 23: Using Original Navigation Button
3.4 Using Original Navigation Button If you want to use OEM NAVI button for changing modes, you need to connect to 16 pin connector wiring. - Case of A8 - Find cables bundle connected to OEM DVD device (in glove box or under OEM monitor) and connect orange wire from POWER cable with white wire of OEM DVD device. -
Page 24: Can Cable Connection
3.5 CAN Cable Connection If you connect the CAN cable in models with ”MODE” handle button, you can change modes via “MODE” button. Connection to CAN COMFORT bus shall be performed according to car schematics in each separate case to avoid car modular units damage. Above you can see example of connection to CAN COMFORT bus in Audi Q7 of 2010 model year. -
Page 25: Troubleshooting
4. Troubleshooting Q. I can not switch A/V sources. Check IR or Ground cable, and MODE button connection. Check LED lamps in the interface, if they are not on, check power cable. Q. All I got on the screen is black. A.