TANDBERG C20 Administrator's Manual page 35

Quick Set C20/C20plus
Contents Introduction
Contents Introduction
Example:
xConfiguration Video MainVideoSource: Camera
xConfiguration Video Monitors:
<Single/Dual>
The codec can be used with more than one monitor and this setting lets you set the codec's monitor layout
mode to Single or Dual.
Single: The same layout is shown on all monitors.
Dual: The layout is distributed on two monitors.
Example:
xConfiguration Video Monitors: Single
xConfiguration Video OSD Mode:
The Video OSD (On Screen Display) Mode lets you define whether or not graphical information and icons on
screen should be displayed.
On: Set to On to display the on screen menus, icons and indicators (microphone on/off, encryption on/off).
Off: Set to Off to hide the on screen menus, icons and indicators (microphone on/off, encryption on/off).
Example:
xConfiguration Video OSD Mode: On
xConfiguration Video OSD Output:
The Video OSD (On Screen Display) Output lets you define which monitor should display the on screen
menus, information and icons. By default the OSD output is displayed on the first monitor.
If you have a single monitor and you cannot see any OSD on the monitor: If the OSD output has been set to
the second monitor and the second monitor is not connected, then you cannot see any menus, information
or icons on the screen. To move the OSD output to the first monitor press the following shortcut sequence
on the remote control. Press the Disconnect key followed by: * # * # 0 x # (where x is output 1 or 2).
Example:
xConfiguration Video OSD Output: 1
xConfiguration Video Output HDMI [1..2] MonitorRole:
The monitor role describes what video stream will be shown on the monitor connected to the output
connector. Applicable only if the monitor configuration is set to dual.
First: Show main video stream.
Second: Show presentation video stream.
Example:
xConfiguration Video Output HDMI 1 MonitorRole: First
xConfiguration Video Output HDMI [1..2] Resolution:
24_768_60/1280_1024_60/1280_720_60/1920_1080_60/1280_768_60/1360_768_60/1366_768_
60/1600_1200_60/1920_1200_60>
Select the preferred resolution for the monitor connected to HDMI video output. This will force the selected
resolution on the monitor.
Auto: The system will automatically try to set the optimal resolution based on negotiation with the connected
monitor.
Range: 640x480@60p, 800x600@60p, 1024x768@60p, 1280x1024@60p, 1280x720@60p,
1920x1080@60p, 1280x768@60p, 1360x768@60p, 1366x768@60p, 1600x1200@60p, 1920x1200@60p
Example:
xConfiguration Video Output HDMI 1 Resolution: 1920_1080_60
D14489.01—JULY 2009
Getting started About the menus
Getting started About the menus
<On/Off>
<1..2>
<First/Second>
<Auto/640_480_60/800_600_60/10
Advanced settings Settings library
Advanced settings Settings Library Settings library
xConfiguration Video Output SecondMonitor PresentationOnly:
Determine if the system shall show presentation only on the second monitor in a dual-monitor setup.
On: Forces the second monitor to be used for presentation only in a dual-monitor setup.
Off: The system will automatically select what to show on the second monitor.
Example:
xConfiguration Video Output SecondMonitor PresentationOnly: Off
xConfiguration Video Selfview:
The Video Selfview setting determines whether or not the main video source (selfview) should be displayed
on screen.
On: Set to On when you want selfview to be displayed on screen.
Off: Set to Off when you do not want selfview to be displayed on screen.
Example:
xConfiguration Video Selfview: On
xConfiguration Video WallPaper:
The Video Wallpaper setting determines whether or not a background picture should be displayed on
screen when idle.
None: Set to None if you do not want a wallpaper to be displayed on screen.
Summersky, Growing: Select the wallpaper to be displayed on screen.
Custom: The custom wallpaper is uploaded from the web interface. Open a web browser and enter the IP
address of the codec. Select "Wallpaper" from the menu on top of the screen. Browse for the file and press
the "Upload" button. Toggle once between "None" and "Custom" wallpaper to make the change take effect.
See the Appendices section for further details about the web interface.
Example:
xConfiguration Video Wallpaper: Summersky
Administrator Guide
Cameras Appendices
Cameras Appendices
<On/Off>
<On/Off>
<None/Growing/Summersky/Custom>
Contact us
Contact us
35